Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 4186 - 4200 of 4519 products found.

  • DC Parametric Test System with Curve Trace

    DC3 - Hilevel Technology, Inc.

    The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.

  • Contact Resistance Measurement System

    CRMS - Ultra-Tech Enterprises, Inc.,

    The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers

  • High Voltage Switching System

    Vitrek Corporation

    The manual method is extremely problematic. Slow, error prone, labor intensive, operator hazardous – don’t even think about recording the test results. The 964i on the other hand, is purpose built to fully automate all of you HV switching needs. You chose the 964i, partnered it with a Vitrek 95X Series Industrial Strength Hipot Tester and QuickTest Pro test automation software. The company wins the Malcolm Baldridge National Quality Award, you get a promotion and that corner office you’ve always wanted. Choose carefully.

  • H/L Voltage Clamp Meters

    MEWOI Electronics Co.,ltd

    High Voltage Current Transformation Ratio Tester breaks traditional structure, specially designed for high and low voltage first and secondary loop current, variable ratio, and current leakage test; apply the latest CT technology and mask digital integration technology, composed of special high-voltage clamp, low voltage clamp, host, high voltage insulation rod and monitoring software, etc; its wireless transmission test data can penetrate multiple building obstacles with a straight-line distance of 30 meters.

  • Mass Interconnect Solutions

    ECT

    Mass interconnect systems act as the connector interface between test instruments (PXI, VXI, LXI, GPIB, SCXI & PCI) and devices / units under test (DUT / UUT) These are often used in Defense, Aerospace, Automotive, Manufacturing, and other applications. By mating a receiver on the tester side with an interchangeable test adapter (ITA) on the UUT, the mass interconnects enables the entire system to mate together at one time. Mass Interconnect Systems are available in multiple sizes and configuration to accommodate virtually any testing requirement.

  • MegaTester

    Megatester, Inc

    The Megatester End-Cap is what makes the Megatester work. Normal AA flashlight end-caps are simply there to hold the batteries in place and to complete the circuit. The Megatester End-Cap allows you to use your flashlight as a continuity tester. It safely diverts the 3 volts from the batteries to a test lead. When in its stowed position, clipped to the end-cap, the flashlight operates normally.

  • Memory Test Systems

    T5503HS - Advantest Corp.

    With today's mobile electronic devices and the servers that support them handling ever-increasing volumes of data, semiconductor memory manufacturers need a highly capable, cost-efficient means of testing their latest generations of high-speed, high-capacity memory ICs including emerging DDR4-SDRAM and LPDDR4-SDRAM chips. Advantest's T5503HS tester gives memory manufacturers that industry-leading performance and a low cost of test along with an upgradeable system design.

  • IP Performance Analyzers

    NuBAR-1000 - Omnicor

    NuBAR-1000 is an ideal Ethernet tester for testing and troubleshooting potential problems of data transmission and bandwidth in the field. NuBAR-1000 works by pair with roles of Lord and Servant. Without extra standby personnel at the other test site, two NuBAR-1000 negotiate with each other automatically, start bi-directional symmetric / asymmetric wirespeed transmission, synchronize the test result and store result at Lord NuBAR-1000.

  • JTAG External Modules for Cluster Test

    JEMIO - StarTest

    The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.

  • Keypad Test system

    Mistral - Engineering Solutions Inc. (ESi)

    The Mistral Keypad Test System has been designed to be the least expensive, easiest to use full featured tester for membrane switch assemblies. The idea is to combine a small, smart "pod" with a PC running software that makes full use of the Windows® graphical interface. Make it as easy to set up and use as possible yet include all the features you need.

  • Low Energy Plastic Impact

    IT 503 & IT 504 - Tinius Olsen

    The model IT 503 plastics impact tester, together with the model IT 504, continues to set the industry standard for versatility, ease of operation, and display of information with high resolution. The primary difference between the IT503 and the IT504 is that the model IT504 is supplied without the interlocking safety shielding. These machines are capable of determining the impact resistance using either a Charpy or Izod configuration, without changing the entire pendulum.

  • LTE Emulation for End-to-End QOS Validation

    IxLoad-Wireless XAir2 - Ixia

    Ixia’s XAir2 load module provides LTE user equipment (UE) emulation that enables a powerful IxLoad eNodeB Layer 1 to 7 test solution. With complex UE modeling, it offers realistic and easily-configured traffic models and call patterns. Using IxLoad’s real-world subscriber modeling, testers do not need to be protocol experts to develop test realism. From a single tool, users can perform capacity tests, detail a cell throughput, measure voice and video quality, model a wide variety of mobility scenarios.

  • LEON Desktop

    Konrad Technologies GmbH

    Based on standard PXI chassis and optionally equipped with the ABex technology, the LEON Desktop offers test engineers a flexible and cost effective test solution for desktop use or integration in customized test systems. It can easily be extended by functional test and boundary scan modules. As well as all testers of Leon Family the KT LEON Desktop is based on the multifunction card KT-PXI-501.Benefits Easy implementation Low cost Test in paralell Open Platform PXI Extrem modular

  • Lightweight Polyphase Test Set

    679 - Red Phase Instruments Australia Pty Ltd.

    For many field testing applications a small, light and moderately priced tester is more attractive to utilities than a larger traditional unit. To keep weight as low as possible the 469 only has 1A and 5A ranges for testing C.T. operated meters. However, it is still easy to test direct connected meters up to 100A with the optional precision clipon C.T.s.

  • LED Analyser

    Feasa - Intrinsic Quality,Inc

    Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order: