Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing


Showing results 4321 - 4335 of 4563 products found.

  • CPCI BUS Interface Card

    Cpci301 MIL-STD-1553 - Andor Design Corp.

    MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.

  • Creep Testing Machines

    GNCJ Series - NCS Testing Technology Co., Ltd.

    This tester is used to measure stress-rupture properties of various metal and alloy materials under high temperature. Tests are conducted and data are provided according to GB/T2039-2012, HB 5150-1996, HB 5151-1996 and other relevant standards.It uses high-precision weights to provide constant test force, and PLC control system is provided for fully automatic operation.To make sure the long time tests, redundancy designs are considered in both hardware and software.

  • C-Mic Auto Test System

    BK9010B - BaKo Co., Ltd

    Based on the BK3010 C-Mic Tester, the BK9010B is our fastest C-mic test system. Fully automatic, with 4 or 8 couplers and test time of about half a second, you can test and sort 80 C-mics per minute 4800 per hour, or upwards of 3 million C-Mics per month (based on 6s total cycle time)! The robotic loader lines up the microphones and loads them onto the couplers for testing. Then it sorts passing microphones into 8 quality classes and failing microphones according to the reason they failed.

  • Common Bench-Top Automatic Test Set

    CBATS - CACI, INC.-FEDERAL

    The Versatile Testing Solution for Critical Avionics. CBATS Model 101 and 201 testers are capable of supporting diagnostic and acceptance test requirements for a wide assortment of avionics systems (instrumentation, flight computers, and other electronic assemblies) with application for both military and civilian land, sea, and air platforms. The tester's capabilities are completely automated and require little or no operator input.

  • CompactFlash™ Socket Saver and Extender Cards

    CF extend 162 - Sycard Technology

    In a high volume production environment a CF test 220 socket tester may see several thousand insertion/removal cycles a month. To prevent wear and tear on the CF test 220's 50-pin connector, Sycard supplies a low-cost socket saver, the CFextend 162. The CF extend 162 is inserted between the CompactFlash™ socket and the CF test 220 unit.

  • Circuit Breaker Timer Interface Unit

    CBTI-1201 - Vacuum Interrupters, Inc.

    We are pleased to introduce the CBTI-1201 circuit breaker timer interface unit, a multi-use tester designed to operate and interact with all types of circuit breakers. It is a light-weight, portable unit that incoporates a power supply for charging spring charged breakers while outside their cubicle, switching to trip and close the breaker, provisions to easily attach an external breaker timer, and has unique cable sets which speed and simplify connection to the breaker under test.

  • Circuit Indentifiers

    Extech Instruments Corporation

    Circuit Breaker Finder/Receptacle Tester that locates circuit breakers and tests receptacle wiring. Allows the user to quickly locate 110 Volt to 125-Volt AC circuit breakers and fuses with audible and visual circuit breaker indication. The product also features a variable sensitivity adjustment to pinpoint correct circuit breaker. This product is complete with a year warranty, the receiver and GFCI transmitter and a 9V battery for the receiver.

  • DUT Boards

    Robson Technologies, Inc.

    RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.

  • DUT Prototype Board

    DPB8800 - Applied Test Resources

    The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.

  • Electrical Fast Transient Generator

    EFT 500N5 - EM Test

    The EFT 500N5 is the state-of-the-art EFT / Burst tester with a built-in coupling/decoupling network for single phase or three-phase mains supply lines and a HV terminal to connect a capacitive coupling clamp. The spike frequency can be varied from as low as 100Hz up to 1,000kHz. The EFT 500N5 is capable to generate 10,000 spikes per second or up to 1,000 spikes per burst.

  • Electrical Fast Transient Generator

    EFT 500N8 - EM Test

    The EFT 500N8 is the state-of-the-art EFT / Burst tester with a built-in coupling/decoupling network for single phase or three-phase mains supply lines and a HV terminal to connect a capacitive coupling clamp. The spike frequency can be varied from as low as 100Hz to 1,000kHz. The EFT 500N8 is capable to generate 1,000 spikes per second or up to 150 spikes per burst.

  • Expert Digital Automotive Analyser

    DMM5 - Draper Tools Ltd

    Expert Quality, Ideal for automotive use. Display packed.Features include:24 position rotary function and range selector; Measures DC volts and DC amps; Measures resistance and dwell angle; Takes tachometer readings ; Diode test facility; Audible continuity tester; Impact resistant rubber case; Recessed input terminals; Low battery indicator; Test leads (probes and crocodile clips)

  • F-35 Armament Test Set

    MTS-235 - Marvin Test Solutions, Inc.

    The MTS-235 is a state-of-the-art portable test set for various armament systems used on the F-35 Joint Strike Fighter including launchers, pylons, and racks. It combines the test capabilities of an I-Level test set in a compact, rugged, flight-line qualified enclosure. The MTS-235 performs parametric functional tests on F-35 Alternate Mission Equipment (AME) components including Launchers (iARL and eARL), Pylons (Air-to-Ground and Air-to-Air) and associated subassemblies and adapters. The MTS-235 is a MIL-STD-1760 tester that supports testing of smart weapons systems.

  • Dimensional Calibration

    Alliance Calibration

    123 BLOCKS ANGLE BLOCKS BALL BAR BORE GAGE CALIPERS CHAMFER GAGES CMM'S COATING THICKNESS GAGES CYLINDER PLUGS DEPTH GAGES GAGE BLOCKS GO-NO-GO GAGES HARDNESS TESTERS HEIGHT GAGES INDICATORS LENGTH STANDARDS LEVELS MICROMETERS OPTICAL COMPARATORS PARALLELS PIN GAGES PROFILOMETERS RADIUS GAGES ROUGHNESS SPLINES THREAD RINGS THREAD PLUGS

  • Electrosurgery Analyzers

    Fluke Biomedical

    Electrosurgery Analyzer is the ESU tester you can depend on for complete preventive maintenance and electrosurgical device safety to completely test these critical functions:* Measures current, voltage and power output.* Tests RF leakage from output to ensure no hazardous currents are present.* Performs Return Electrode Monitoring (REM) tests.* Measures crest factor.* Performs automatic power distribution curve at a wide range of test loads.