Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 4576 - 4590 of 4623 products found.

  • Stimulus Induced Fault Testing

    SIFT - FA Instruments

    SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.

  • 100V MEGOHMMETER Surface Resistivity Meter

    B8562 - Botron Inc.

    Portable 100 volt LED megohm tester with two parellel probes and two banana jacks for optional 5lbs weights. a 10 light Surface Resistivity Meter that test at 100 volts. This portable test instrument provides both RTT (resistance top to top) and RTG (resistance top to ground) will measure a wide variety of static dissipative and conductive materials.

  • NETWORK ANALYZER

    Sparnex Instruments

    The network analysis capabilities make this tester the preferred tool of the equipment manufacturer and DSL development groups. They use the ICXACT to debug and improve the data throughput up to the limits imposed by the Physical Layer, while adhering to the recommendations as set by the national Spectrum Regulator and the international Telecommunication Bodies. Service Providers are using it to probe the quality of the service over the network.

  • Strength Meter

    NOVOTEST IPSM-U+T+D (Pulse Velocity Tester) - NovoTest

    The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete).  Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).

  • SPECTRUM ANALYZER

    xDSL - Sparnex Instruments

    The spectrum analysis capabilities make this tester the preferred tool of the equipment manufacturer and DSL development groups. They use the ICXACT to debug and improve the data throughput up to the limits imposed by the Physical Layer, while adhering to the recommendations as set by the national Spectrum Regulator and the international Telecommunication Bodies. Service Providers are using it to probe the quality of the service over the network.

  • Ultrasonic Testing (UT)

    SONOTEC Ultraschallsensorik Halle GmbH

    Applications of ultrasonic testing vary, ranging from weld inspection to wall thickness measurement and the detection of discontinuities such as invisible cracks, inclusions, voids and other discontinuities in metals, plastics, ceramics and composites. Experienced material testers have supervised the development of SONOTEC flaw detector and probes focusing on simple operation procedures and high sensitivity while simultaneously providing a robust design.

  • In-Circuit Test Fixtures

    Drop-In - Circuit Check, Inc.

    The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components.  The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.

  • Electrical Equipment ATS

    8900 - Chroma ATE Inc.

    8900 electrical equipment ATS can completion that amount measurement and test procedure in once automatically.This strong function not only can be report formatted simply, but reduce the careless mistake of the artificial writing and improper test. Chroma 8900 electrical equipment ATS is suitable for all electrical equipment test solution within Electrical Safety Test. Chroma 8900 electrical equipment ATS solve the Electrical Safety Test and special FUNCTION test solution. The system can combine different testers in the system accordding with different test request what your need. The software is all open architecture structure which can offer the corresponding program and the most flexible test item in accordance with special test procedure to the customer for special products. The all open architecture software of 8900 systems includes the strong report editor and generator, statistical analysis and functions of management. Management of various types of different test reports and operation that these functions make the system have the ability to control quality and reduce risk. These statistical analysis and report function are indispensable for quality control and product line testing in a modern electrical manufacturer.

  • Glove - Sleeve Testing Machines

    L,M,N Series - The Von Corp

    The L, M and N Series is The VON Corporation’s fully automated, microprocessor controlled glove and sleeve tester. Units allow testing of Gloves, Sleeves, or Line Jumpers. All standard rubber goods can be tested, even class IV. All machine adjustments are controlled via a menu operated microprocessor control system. With a single selection the test voltage, current limit, depth, water fill level, test time, blower speed and exhaust fan speed are set. The operator is required to merely load gloves in the special clothespins, lower the test electrode into the glove and press the start button. Automated water fillers will fill the glove in less than 30 seconds. Tests are timed and an audible alarm sounds failures or test complete, with bright flashing colored lights signaling which position failed, or test complete. The –W option allows use of the VON Hammock method on all positions. An extra wide and long tank allows testing of the sholder portion of sleeves and allows 11” spacing between sleeves.

  • Motor Test for Electric Scooters

    M.E.A. Testing Systems Ltd.

    *The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.

  • Drop Weight Impact Testing Machine

    DWTT Series - Jinan Testing Equipment IE Corporation

    DWTT Drop Weight Impact Testing System is suitable for drop weight tear test of various kinds of ferrite, especially for the test of DWTT for pipeline steel as ASTM-E 436, API-RP 5L3, ASTM-E 208 and DIN EN 10274. DWTT has integrated mechanical, electrical, and automatic control technology, and achieved full automation of feeding, hammer lifting impact, and fracture specimen collection. The load frame has a four-column design, features in stable supporting structure, rigid, dual sliding rails. The Drop Weight Drop Weight Tester is equipped with positioning mechanism, anti-dumping mechanism, safety mechanism, hydraulic buffer devices and security guard net. The impact energy is determined by the lifting height and configuration of different net weights. DWTT Drop Weight Impact Testing System is the essential quality control equipment for pipeline manufacturers, steel mills, iron and steel enterprises, and is also widely used for research institutes.1. Buffer device is equipped to avoid the second impact and absorb the residual energy after breaking the specimen so as to prevent the weigher and anvil from destroying. The installation of safety mechanism, buffer device, and security guard net will effectively secure the testing machine and its operation to extend its life.2. Configuration of the specimen-feeding system, anti-second impact device, and specimen centering mechanism will guarantee a quick, accurate and reliable test.

  • Fiber Optic Test Equipments

    Ingellen Technology Co.,Ltd

    Fiber Optic Test Equipments are tools used to test electronics and measure equipment to ensure proper function and efficiency. Test Equipment can be used on several types of instruments and tools. Ingellen designs and manufactures optical test equipment for use in the fiber optic datacomms and telecomms industry. We offer many kinds of fiber optic test equipments. The range of products from Ingellen is also extensively used in manufacturing and test environments. Ingellen fiber optic tester equipment offers practical specifications to help you test fiber systems and helps you get your job done efficiently.

  • Handheld Optical Power Meter

    HOPM-3216 - Hangzhou Huatai Optic Tech. Co., Ltd.

    HOPM-3216 Handheld Optical Power Meter is our newly designed fiber optic tester, it aims at fiber network installation, fiber network engineering acceptance and fiber network maintenance. Combined usage with HOMP3116 handheld optical light source, it offers a quick and accurate testing solution on both SM and MM fibers. Compared with usual power meters, the HOPM-3216 has more great functions/features of automatic wavelength identification and switching and intelligent backlight control. Also the HOPM-3216 features good appearance, good touch feeling and considerate humanity design.

  • Dual Space Electro-hydraulic Servo Universal Testing Machine

    WAW-E Series - Jinan Testing Equipment IE Corporation

    WAW-E series computer control servo-hydraulic testing machine is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, the servo-hydraulic tester of dual space is capable of controlling the test procedures by the predetermined programs. The computer control servo-hydraulic testing machine can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The servo-hydraulictesting machine is easy to operate and is versatile in the applications of metallurgy industries such as steel mills & alloy, reinforced bar, aircraft manufacturer, research institutes, laboratories, calibration institutes etc.

  • 7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit

    #8029 - Innovative Products of America

    Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner