Filter Results By:

Products

Applications

Manufacturers

Showing recent results 4651 - 4665 of 4761 products found.

  • JTAG External Modules for Cluster Test

    JEMIO - StarTest

    The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.

  • Multi Protocol Boards

    Excalibur Systems, Inc.

    The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.

  • OBD ECU Simlator

    mOByDic1700 - Ozen Elektronik Inc.

    The J1939 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates a Truck ECU . Using 5 potensiometer , 5 live data can be changed and some fixed PNG values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. DM11 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 24 V power supply . More information you can get from the corresponding chipset datasheet.

  • Ohm-Stat Digital Display Megohmmeter

    Static Solutions Inc.

    Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester

  • On-Wafer Measurements

    Keysight Technologies

    Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.

  • Piezoelectric Testing

    Radiant Technologies, Inc.

    Radiant Technologies, Inc. specializes in the measurement of electrical and piezoelectric properties of non-linear materials.   The Piezoelectric Task captures a sample's displacement  as a function of voltage profile along with the sample's polarization response.  An external displacement measurement instrument must be attached to a Radiant Precision Test System to make this measurement.  All of the Radiant testers are equipped with a high-impedance voltage input to capture the output of a displacement sensor. Every Vision measurement task will collect data from that sensor input simultaneously with the measurement being executed. Radiant's test systems work easily with displacement sensors which include:

  • Relay Buddy

    190 - Electronic Specialties Inc.

    Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.

  • Super Megohm Meters

    SM7110 and SM7120 - HIOKI E.E. Corp

    Both products are designed for use in evaluating and testing the performance of electronic components used in products such as smartphones and hybrid vehicles. To accommodate vehicle components with increasingly high breakdown voltages, the SM7120 is the first insulation tester in the world to be able to output a measurement voltage of 2000 V (the SM7110 supports measurement voltage output of up to 1000 V). In addition, both products can complete testing twice as quickly as the previous Hioki model while offering dramatically improved measurement reproducibility and noise resistance. As a result, the new instruments promise to significantly improve evaluation and testing productivity.

  • Sweating Thermal Guarded Hotplate

    Sataton Instruments Technology CO., Ltd

    Sweating guarded hotplate is the textile testing instrument for measuring of thermal and water-vapour resistance properties under steady-state conditions. By testing the thermal resistance and water-vapour resistance of textile materials, the tester provides a direct data for characterizing the textiles’ physiological comfort which involve a complex combination of heat and mass transfer. The hotplate is intended to simulate the heat and mass transfer processes which occur next to human skin and measure the hence transport properties in a steady-state conditions involving combinations of temperature relative humidity, air speed, and in liquid or gaseous phase.

  • Terminal Power Meter

    TPM-50A - ShinewayTech

    ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm;(3) Modulation bandwidth: 5MHz;(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.

  • Test Analysis for Land Seismic Systems

    Testif-i Land - Verif-i Ltd

    Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.

  • Transformers Testing

    TTRT 03A S2 - Amperis sl

    The ATRT-03A is Amperis' second generation, microprocessor-based, automatic, three phase, transformer turns-ratio tester. This lightweight, portable, battery-powered unit is designed for testing transformers at utility power substations. The ATRT-03A determines the transformer turns-ratio using the IEEE C57.12.90 measurement method. The transformer turns-ratio (ranging from 0.8 to 15,000) is determined by precisely measuring the voltages across the unloaded transformer windings. To ensure accuracy, the ATRT-03A's measuring circuitry self-calibrates before each measurement. It requires neither adjustment nor temperature compensation. The ATRT-03A's turns-ratio measurement accuracy is 0.1% or better.

  • Wireless Test Solution

    Chroma ATE Inc.

    Adivic/Chroma Group has been in the development of RF & Wireless test solutions for more than a decade. Take RF Recorder as an example, it has been adapted by all major Japanese & Korean automotive brand names such as Mitsubishi, Honda, Hyundai,.. ,most of the global IC design houses with DTV chips, and also military entities in NATO. With the same customer-proved Software Defined Radio architecture, we have introduced Wi-Fi, Bluetooth tester since 2014. It will soon cover other current/future wireless standards such as 4G/LTE, 802.11ax, 802.11ah, etc.

  • Brake Testing Technology

    Maschinenbau Haldenwang GmbH & Co. KG.

    The brake test technology is mainly used to test the effectiveness of the braking system of motor vehicles. Depending on the application, roller brake testers or a deceleration measuring device are used. These are available in different versions depending on the type of vehicle and the structural situation.

  • Fiber optical OTDR

    ST3200 - Shandong Senter Electronic Co., Ltd

    ST3200 OTDR (Optical Time Domain Reflectometer) is an intelligent optical fiber communication tester. This tester is easy to use and portable, which has a 3.5-inch color LCD touching screen. It also possesses events intelligent analysis and more user—friendly operation. It is an ideal test instrument for the fiber testing and troubleshooting. It can test the length of optical fiber and optical fiber cable attenuation coefficient. It can exactly display the loss distribution curve of the optical fiber and cable as well as the loss between two points and the joint loss. It also can test the distance between two points and the position of joint, fault point as well as breaking point. With mature VFL (Vision Fault Locating) system, so it becomes convenient to test the fault location of jumper wire.Ⅱ. Main functions·Test the distance between two points and dynamically display the distance between two cursors·Test the loss between two points and the loss constant of the optical fiber and cable·Test the joint loss·Auto-optimization and quick response·Search for the event points automatically·The function of wave form storage: it can store the wave form data and test condition into the disk and the stored information also can display again.·Support the function of copy: it can copy the data file which is built in the internal disk into the U- disk directly.