Showing results: 646 - 660 of 5276 items found.
-
EASYTEST -
HT Italia Srl
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
IQ2010 -
LitePoint Corporation
The LitePoint IQ2010™ is a comprehensive, one-box test solution for all your connectivity testing needs:WiFi, 802.11a/b/g/n and 802.11pBluetooth, Classic (1.x, 2.x, 3.0) and Low Energy (4.0)GPSFMMIMOWiMAXZigBee
-
Amoeba 4200 -
Aemulus Corporation Sdn. Bhd.
4200 is capable of running multiple test sites independently with a parallel efficiency of up to 85% for quad-site and octal-site testing.It comes with test development and production software suite, which makes the transition from test development and bench characterization to production seamlessly.
-
TriboLab CMP -
Bruker microCT
Leveraging over 20 years of CMP characterization expertise with its predecessor product (Bruker CP-4), TriboLab CMP brings a complete set of capabilities to the industry-leading TriboLab platform. The resulting accuracy and measurement repeatability enables the highly effective qualification, inspection, and ongoing functionality testing required throughout the CMP process.
-
G5.DT -
Regatron AG
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
S21 and S21R Series -
Ferrites India
Incoming material inspection can be very useful where strict quality standards are maintained. It saves a lot of processing cost since lossy material is inspected at the entry level before it goes to production level. Epstein Stack testing is one of the oldest and widely used methods for electrical sheet testing.
-
Focus-4000 -
Kyoritsu Testsystem Co., Ltd.
Programmable power supply(User can select big volume or high accuracy model)Fixed power supply (5V/12V/24V acceptable)High accuracy current measurement(MAX 2A) - FX710Voltage measurement MAX 16points(within +/-60V) - FX710Short relays 16pcs (MAX current 1A) - FX62024CH digital input output pins(8pcs per unit, IN/OUT setting) - FX700/FX71016 open corrector output for controlling external relays16 port (simultaneously 2 ports ) Oscilloscope channel for observing wave formCommunication function RS232C/GPIB(Standard)、CAN/LIN communication, Programmer(Options)Focus-2000Plus unique in-circuit Test(ICT)function
-
METRISO® 3000 -
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportA barcode scanner can be used in order to record measurement points before testing
-
Future-Tech Corp.
By adopting the Load-cell load system, multi-stage load switching is possible.
-
MT91 Series -
Newage Testing Instruments, Inc.
The Newage MT91 System is an automatic microhardness testing system that uses the Rockwell method for the hardness result. Hardness is measured based on the depth of penetration rather than using an optical system to determine hardness based on the impression diameter.
-
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a range of microhardness testing solutions including the cost-effective MT91 and MS-ZH microhardness testing system.
-
all-sun
s an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition, namely its capacity for accumulating charge and any possible flaws affecting the battery's performance and security.
-
all-sun
Test voltage can be changed by the rotary switchLED used as normally working indicator under high voltage conditionAudible continuity
-
all-sun
This hand-held digital logic probe provides convenient and precise use in the measurement of logic circuits. It displays logic levels (high or low), pulses and voltage transients down to 25 nanoseconds. High intensity LED readouts provide instant response to the logic state. Tests all logic families TTL/LSI, and CMOS/MOS digital circuits.
-
Benz Co., Inc.
Has automated the test process with microprocessor-controlled data acquisition. Designed to provide the expected internal bond strength for various types of paper, coated products and paperboard, this instrument measures the impact energy imparted to the specimen. The machine consists of a base, sample-preparation press, tape dispenser, dual-range pendulum (0 to 0.325 ft. lbs. and 0 to 0.650 ft. lbs.) and Digital Display. Internal Bond software is available.