Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 691 - 705 of 4490 products found.

  • In-Circuit Tester

    ZPC7000ST - OKA-NO (S) PTE LTD

    √ Compact design with free layout (can be operatedwith notebook PC).√ 40% increase in measurement speed.√ Easy-To-Use window-based software with networkcapability.√ Compatible test data with other Okano ZPCsystems.√ Operator standing and sitting type available.

  • In-Circuit Tester

    AT-01 - OKA-NO (S) PTE LTD

    The Okano AT-01 accurately detects shorts, open, wrong components, missing components and reverse mounted components for resistor, capacitor, diode, transistor, inductor, LED and FET. And AT-01 is especially designed to detect open pins of ICs.

  • Pack Tester

    MS-152 - Misum Systech Co., Ltd.

    This equipment is used for inspecting condition of cell or pack through charge/discharge operation, to make a precise measurement of performance characteristic, consumption current, ID/TH Resistor, initial resistance. Depends on the setting value, OK or NG will displayed.

  • Pack Tester

    MS-154 - Misum Systech Co., Ltd.

    This equipment is used for inspecting condition of cell or pack through charge/discharge operation, to make a precise measurement of performance characteristic, consumption current, ID/TH Resistor, initial resistance. Depends on the setting value, OK or NG will displayed

  • Earphone Tester

    MS-158 - Misum Systech Co., Ltd.

    This equipment is used for inspecting state of earphonethroughmeasurement of resistor, consumption current and sensivity. Depends on the setting value, OK or NG will displayed.

  • BMS Tester

    MS-159 - Misum Systech Co., Ltd.

    This equipment used for F/W writing, Calibration and function test. It inspect current, voltage protection mode, consumption current and cell balancing measurement to check the state of BMS and applied to the full inspection and mass production.

  • Transformer Testers

    101T/102T - AB Instruments, Inc

    Model AB-101T is designed to have all parameters of two winding of any transformer in a single go.This is particularly used to have full transformer data is available on PC.Micro –Controller based meter,that provides all parameters that are selected to be available on PC with two winding jig.It normally gives L,R & Q but other parameters can be selected.. With basic accuracy of 0.2 %.it offers various test frequencies . Four wire measurement minimizes error in reading. RS232 Communication & Binning facilty upto 8 bins possible. Loading of pre-setted parameters also possible to save time.

  • Fretting Tester

    FFT Series - Rtec Instruments

    Fretting wear is a test where surface damage occurs between two contacting surfaces experiencing oscillatory displacement of small amplitude. At the contact point, lubricant/coating is squeezed out or the low amplitude motion does not permit the contact area to be re lubricated/ debris dislodge resulting in serious local wear occurs. This type of wear causes two-body abrasion, adhesion and/or fretting fatigue wear.

  • Tribocorrosion Tester

    ASTM G119 - Rtec Instruments

    Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.

  • Safety Testers

    60204 - Whitelegg Machines Ltd

    Easy to read colour screeninnovative handy data entry via an illuminated rotary buttonstructured menu with practical functional buttonsmultilingual user softwarelarge storage capacity for subsequent data transferPE resistance test in four-wire-technologyinsulation resistance testhigh-voltage test incl. burning functionilluminated ring around the rotary button to shows the high-voltage levelresidual voltage testself-test via black box according to VDE regulationselectronic PE test current controlPE test with resistance or voltage drop displayelectronic high-voltage settinghigh-voltage with ramp up/down timethree HV modes: manual, automatic with time lapse and burningworldwide voltage supply 110V…250V / 47…63Hztest start upon touching the test object with the PE test probeacoustical and visual status messagespassword protectiondigital I/O interface and analog actual value outputs for connection to other devicesinterfaces for printer, remote control or result queryintegration into production lines with PLC / PC remote controltwo-circuit safety inputssafety circuits with restraint-guided safety relaysPrintCom-software to save and print test results on a PCdesigns options: tabletop unit, box unit, mobile caddy, 19”-installationcan be fully configured and optimised for specific OEM requirements

  • Impulse Tester

    SCR ELEKTRONIKS

    Testing as per IEC 61180, IEC 61008-1, IEC 60335, IEC 60950, IEC 60947The Impulse Voltage Test Equipment is designed to generate voltage impulse of 12kV (as per model) (both pola rities, settable). The wave form generated has a rise time of 1.2 micro second and 50 micro second duration. This test is described in various standards including IEC 61180.

  • Compressor Tester

    M.E.A. Testing Systems Ltd.

    Full load performance from stall up to no-load, without coupling to external load, including: torque, speed, current, auxiliary current, main current, voltage, capacitor voltage,input power, output power, power factor, motor efficiency,direction of rotation.

  • Fan Tester

    M.E.A. Testing Systems Ltd.

    Analysis of real-time behavior of fan systems, including the fan's load curve. Without connecting to any sensor, provides:fan's load curve, input and output performance of the fan's nominal working point, friction and mechanical defect testing.

  • Bearing Testers

    Anderon Meters - M.E.A. Testing Systems Ltd.

    *Measures the anderon value in an assembled bearing.*Detects slight surface irregularities arising from machining imperfections and other factors.*Detects displacement in a radial direction caused by rolling surface irregularities.*Provides the “anderon” value, a numerical expression of the degree of vibration and noise in the bearing, allows quantitative assessment of bearing performance.*Enables the discovery of the causes of vibrations (scratches on the raceways of outer and inner races made during machining, scratches on ball surfaces, contamination by dust particles, etc.).*Enables the sorting of bearings by precision class and more accurate assessment of bearing quality.*Development of high-quality products: aids in the development of high-quality, durable bearings that generate minimal vibration and noise.*Assurance of product quality: allows data to be gathered that can be used for objective assessment of quality, particularly vibration and noise characteristics.*Optimal management of products by quality: High-sensitivity detection of minute but critical variations in product characteristics, allowing to sort bearings accurately by quality for optimal product management.*Improved productivity: allows inspection of bearings before installation in high-precision, high-performance products susceptible to vibration, minimizing defects in assembled products and improving productivity.*Optimal parts control in the open market environment: permits high-accuracy acceptance inspections of delivered parts, allowing to test various samples obtained from both domestic and overseas manufacturers to help secure parts that offer optimal quality.

  • CCTV Tester

    ANA-GCB002E - Shenzhen ANA Electronics Technology Co.Ltd

    3.5-inch TFT-LCD screenVideo testingAudio input testingUPT cable testing12V DC, 0.4A power outputSignal mode: NTSC/PALDisplay: 3.5-inch TFT color LCDImage resolution: 640 x 480 pixelsVideo input x 1 (BNC connector)Audio input x 1 channel audio inputDC power output x 1 maximum electric currency 400mABattery specification: built-in rechargeable lithium battery, 3.7V, 2,000mA/hPower input: 5V DC at 1.0ALight instruction: 2 LED indicator, power indicator (green)/charging indicator (red)