Showing results: 2551 - 2565 of 8504 items found.
-
PXIe-3985 -
ADLINK Technology Inc.
The ADLINK PXIe-3985 PXI Express embedded controller, based on the fourth generation Intel® Core™ i7 processor is specifically designed for hybrid PXI Express-based testing systems, delivering maximum computing power for a wide variety of testing and measurement applications.
-
Interpower Corp.
A SafeBloc is an accessory device, which can be used with other test equipment, as an adapter, to connect and test power cords and wiring harnesses for production testing purposes, prior to installation into equipment. Such testing would include Hipot and continuity testing of the power cord or wiring harness. The SafeBloc allows the bare wires of a power cord or wiring harness to be connected to the test equipment via clips inside the enclosure. Power can only flow through the device once it is closed and the test sequence is then started, ensuring that the test operator will not get shocked during the testing procedure. Power cord manufacturers and CEMs manufacturing custom wiring harnesses would be typical users of such a device.
-
WECO 9000 -
Radian Research, Inc.
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
SKZ111 -
SKZ Industrial Co., Ltd
High-frequency paper moisture meter is the high-performance and digital meter for testing moisture, which is firstly introduced to China from foreign countries. The meter uses high-frequency principle. It integrates sensor and mainframe with figure display and has six stalls to test the moisture of various papers, cardboard, corrugated paper and carton. The meter has many advantages, such as large testing range, high accuracy, and small dimension, light and portable for spot testing. It is the ideal instrument in the production process.
-
MD-1750 Series -
Mustang Dynamometer
The MD-1750 has the largest set of rollers in the industry at 50-inches. The 1750 Series is designed for customers whose horsepower testing requirements and drag racing slick tires require a larger, tire-friendly roller configurations. The MD-1750 is available with a wide 96-inch outer track for testing large Diesel Trucks. When coupled with the SE or DE eddy current option, the MD-1750 is capable of properly loading and testing very large diesel trucks without worrying about tire slippage.
-
Shijiazhuang Zhongshi Testing Machine Co., Ltd.
The instrument is used for testing the main material of Polyethylene blown covering film and ethylene-vinyl acetate copolymer(EVA),the average content of Vinyl Acetate(VA)is not less than 4% of the anti-dripping progerty blown covering film within add-type. This instrument is mainly testing the first dripping beginning time and the anti-dripping failure time of the film. It is the ideal testing equipment for science research department, universities, commodity inspection, laboratory, graduate school and quality supervision departments
-
8874 -
Instron
The 8874 is a bi-axial tabletop servohydraulic testing system providing a combined axial and torsion dynamic actuator in the upper crosshead. With a precision aligned twin-column frame and a lower t-slot table, the 8874 meets the challenging demands of a varied range of both static and dynamic testing requirements.
-
NovoTest
The testing with mechanical tensile adhesion tester AC-4624 is performed in the following way. On the testing cover is glued dolly and after that, it is pulled-off with the spring-system of the device. The force which is applied for pulling-off the glued dolly, is displayed in numerical value by the indicator on scale of the device. This value – is the value of adhesion.
-
Process Instruments Inc.
Meeting Water Safety regulations and standards has become a primary concern for all industries. Most municipal and state regulators demand that Backflow Prevention Testing be carried out no less than once per year and that testing devices be calibrated and if required, certified regularly.
-
Apica Inc
Enterprise-class testing and monitoring platform for websites, applications and APIs. Internationally distributed load testing and monitoring agents can regularly and programmatically check your targeted websites. web applications, API services, authentication services, certificates, DNS services, and more for performance and service-level compliance.
-
WT2080-OK -
Lisun Electronics Inc.
WT2080-OK LED Power Driver on line Tester is according to GB/T 24825-2009 and IEC 62384: 2006. It suitable for LED Driver production line testing quick test (0.1s finish the testing). The WT2080-OK can test 1pc LED Driver at one time in the production line.
-
Qinhuangdao Boostsolar Photovoltaic Equipment Co., Ltd
-Double power transmission is controlled separately, the transmission is stable, and the synchronous transmission is realized.-Docking with the assembly line, automatic transmission and positioning, automatic testing of components through probes, and complete automatic testing of components.-It can be used with international famous brand testers such as HAIM and SPIRE.
-
Vidac Solutions
Appliance motors are always evolving and the final testing of those motors gets more complicated every year. We build fully automated testers for domestic or offshore manufacturing facilities that can perform any amount of motor testing that you require with limited interaction by the operator.
-
KV Hipot Power Test Equipment Co.,Ltd
High Voltage testing is usually performed to qualify the device to operate safely during rated electrical conditions, a way to check the effectiveness of its insulation. The objective sought during the high voltage testing will determine the type and amount of voltage applied and the acceptable current flow.
-
SG-P01T -
Jinge Testing Machine Co.,Ltd
The tester is used for cloth,paper,paints, plywood,leather,tile,glass,rubber etc.The testing method is executed to make specimen abraded by a pair of grinding wheels under the specified load.The weight of abrasion loss is the difference of weight for specimens before and after testing.