Showing results: 2386 - 2400 of 5310 items found.
-
6000 X-Series -
Keysight Technologies
1 GHz to 6 GHz, DSO or MSO models See more signal detail with 450,000 wfms/s update rate Isolate signals in seconds with exclusive Zone Touch Triggering Operate hands-free with multi-language voice control Get more functionality with optional integrated digital channels, serial protocol analysis, dual-channel WaveGen and 10-digit counter + 3-digit voltmeter Protect your investment with full upgradability; add options and bandwidth at any time
-
34904A -
Keysight Technologies
The Keysight 34904A module for the 34970A/34972A Data Acquisition/Switch Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your DUT at the same time. Rows or columns may be connected between multiple modules to build 8 x 8, 4 x 16 or larger matrices, with up to 96 crosspoints in a single frame.
-
310104334 -
Virginia Panel Corporation
The 20” G12 Receiver is a slide-mounted receiver. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
MS 1602 -
Meltronics Systemtech
The MIP programmer is used to program, read and erase mission data of Mirage 2000 Aircraft. This system is micro controller based design. This system facilitates to program the four EPROM devices at a time. This system contains four read write slots and one read only slot. Read only slot used to read the device data safely. System also has capability to program the one slot device data to another slot device.
-
Amida Technology, Inc.
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
12-0200 -
Associated Equipment Corp.
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
VectorCAST/C++ -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing C/C++ software components necessary for validating safety- and mission-critical embedded systems.
-
VREMYA-CH JS Company
The trunk amplifier is designed to compensate for attenuation and additional amplification of signals from GPS and GLONASS satellite radio navigation systems as part of synchronization and common time equipment.
-
Ansys Corporation
Ansys embedded software development solutions align the design process according to safety standard objectives, reduce development costs, and accelerate time to certification by a factor of two.
-
PQM-703 -
Sonel S.A.
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
ARC Technology Solutions
ARC has experience with complex, commercially available test executives that are available for high volume production needs. Often times, when you don’t need the horsepower of a full featured executive, you are left with creating a specifically defined test program or crafting your own test sequencer. Rather than go down this path and spending your time on architecture, TestCentre brings a simple, yet elegant solution to this all-common problem. Used in many of ARC’s standard test stations, the robust, sequence based architecture of TestCentre, allows you to focus on the testing task at hand. While having some of the more advanced features found in high-end test executives, TestCentre, when mixed with RF analyzers and PXI based test solutions are a great, low cost solution to help solve your everyday testing requirements. Along with TestCentre and an ARC supplied rack-based test platform, your test challenges can be solved in doing circuit card testing, assembly/module level testing, or depot repair troubleshooting tasks.
-
Pegasus Verification System -
Cadence Design Systems
The Cadence® Pegasus® Verification System is a cloud-ready physical verification signoff solution, which enables engineers to deliver advanced-node integrated circuits (ICs) to market faster. The groundbreaking technology delivers up to 10X improved performance on DRC runs and reduces turnaround time from days to hours. The Pegasus system’s innovative architecture and native cloud processing provides an elastic and flexible computing environment. Customers can now achieve complete full-chip signoff DRC on advanced-node designs in a matter of hours, helping designers deliver products to market faster, or easily run multiple DRC signoff iterations, if needed, at the time of tapeout. The Pegasus system provides a massively parallel architecture. It is the first solution to combine a pipelined infrastructure with stream processing delivering near-linear scalability across 100s of CPUs. The Pegasus system’s gigascale technology enables full-chip signoff DRC in just a few hours versus days. As many designs continue to grow in complexity, the Pegasus system can scale to meet customers’ stringent time-to-market requirements.
-
mks Ophir
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
RKT Series -
MATSUSADA Precision Inc.
RKT series power supply is programmable DC power supply with distinctive turbo function which realises 4-5 times wider coverage of output voltage and current in comparison to conventional DC power supply of equivalent output power.You can apply to wide usage with only one unit but no need to apply power supplies with extra margin for output voltage and current because each unit can output voltage and current flexibly within the range of 400W, 800W and 1600W.
-
TAGARNO A/S
TAGARNO digital microscopes give you unique and easy to use magnification equipment to use in a variety of quality control processes as well as R&D efforts or in your repair and rework in an endless range of segments. The digital microscopy camera technology enables you to see any small object in ultra sharp magnification and to document your work with just a single click. It also allows multiple viewers at the same time and thereby greatly improves collaboration.
