Showing results: 3616 - 3630 of 5310 items found.
-
Frequency Meter -
ZETLAB Company
Frequency Meter is used for measuring the frequency of the signal coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the measured frequency value (frequency of periodic oscillations) and signal cycle time corresponding to the measured frequency. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module, FFT spectrum analyzer or a virtual channel.
-
USB-SA124B -
Signal Hound
The Signal Hound USB-SA124A is a Software Defined Radio (SDR) optimized as a spectrum analyzer. It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists. Using recent innovations in RF technology, the Signal Hound has the sensitivity, accuracy and dynamic range you''d expect in a unit many times its cost.
-
6220 EL -
Standard Electric Works Co., Ltd
● Microprocessor technology ensures high performance accuracy and reliability.● Fully programmable via tactile key pad.● Direct readout of disconnection, time or current.● Voltage measured during test.● Housed in a heavy duty carry case.● Suitable for all industrial, mining and domestic environments.● Display can be customized for special orders.● Indicate voltage and trip Current/Time.● Use binary principle.● True resistor switching.
-
Qualitrol
Multi-functional fault recorder including: -- Disturbance fault record (DFR)- Dynamic disturbance recording (DDR) - Phasor measurement unit (PMU C37-118)- Power Quality (PQ Class A)- Travelling wave fault location (TWS to +/-60m) - Impedance fault location- Protocols (61850, Modbus, DNP3) - Sequence of event recording (SOE)- GPS, IRIG and NTP time sync- iQ+ masterstation software.
-
EPM 9450 -
GE Digital Energy
The EPM 9450 is the entry point for GE's premium 9000 meter series with advanced power quality capability. The unit utilizes ACCU-Measure Technology to provide highly accurate revenue grade readings coupled with advanced data analysis. The unit measures over 15,000 electrical parameters including real time harmonics to the 127th order, voltage surges and sags and a large assortment of advanced monitoring functionality.
-
TS Model -
PJ Electronics, Inc.
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
NI
Oscilloscope Devices are flexible, software‐defined instruments that are versatile enough for both time‐ and frequency‐domain measurements and are offered in industry-standard form factors like PCI and USB. They feature up to eight channels that can sample at speeds up to 2 GS/s. The devices also feature numerous triggering modes, deep onboard memory, and driver software API that includes data streaming and analysis functions.
-
Ansys Corporation
Electromagnetic, Signal Integrity, Thermal and Electro-Mechanical Simulation Solutions. The use of Ansys Electronics solution suite minimizes the testing costs, ensures regulatory compliance, improves reliability and drastically reduces your product development time. All this while helping you build the best-in-class and cutting-edge products. Leverage the simulation capability from Ansys to solve the most critical aspects of your designs
-
4D Technology
PhaseCam dynamic Twyman-Green laser interferometers provide high resolution measurements despite vibration and air turbulence. Dynamic Interferometry® enables PhaseCam laser interferometers to capture full wavefront measurements in as little as 30 microseconds—5000 times faster than conventional phase shifting interferometers. Compact and lightweight, PhaseCams make reconfiguring test setups simple and easy, without vibration isolation.
-
3560 -
Abaco Systems Inc
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
MODEL DPM-3 -
Transducer Techniques, Inc
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
TLP-8010C -
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
ModuLab XM MTS -
Ametek Scientific Instruments
I-V (voltage scans with current measurement - used to characterize electronic and dielectric materials)P-E (polarization / electric field - used to run hysteresis tests to characterize ferroelectric materials) High-speed pulse (used to activate charge carriers in electronic and dielectric materials)Staircase and smooth stepless analog ramp waveformsImpedance, admittance, permittivity / capacitance, electrical modulusC-V capacitance - voltage, Mott-SchottkyAutomatic sequencing of time domain and impedance/capacitance measurements
-
Model 308 -
OAI
Dependable and repeatable, The OAI Model 308 UV Intensity/Power Meter is precise, direct-reading instrument designed to measure UV light intensity. The Model 308 features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port and is available with an optional software package that facilitates instant data logging of intensity mode, time, wave length, serial number and calibration due date.
-
Part No. S20DC30 -
Teledyne Defense Electronics Relays & Coax Switch
Series S20 relays switch medium- to high-power DC loads. These devices feature the latest-generation MOSFET technology as well as an innovative isolated driver to ensure fast power turn on and off. The relays feature triggered control input to avoid linear control risks and fast switching times. The relays also offer an LED for status.Available options include:S20DC30 30A, 0-130 Vdc Load; 4.5-32 Vdc Control
