Showing results: 4426 - 4440 of 5357 items found.
-
DCHT -
Lectrosonics, Inc.
The DCHT portable digital stereo transmitter is designed for use in film and TV production as both a wireless audio link from a bag or cart system to cameras and as a portable IFB transmitter paired with the Duet digital wireless M2R receiver packs. The DCHT accepts two channels of mic or line level analog signals or an AES digital signal from a mixer and transmits to the receiver or receivers in a purely digital format. The digital architecture of the new DCHT is a third-generation design with specially developed, high-efficiency circuitry for extended operating time on two AA batteries.
-
MFCh -
Holding Informtest
*Frequency reproduction accuracy ± 2 x 10 -9 *Output frequency 1 Hz - 10 MHz *Output pulse signal 1 kHz The MFC is designed to generate high-frequency pulse signals with a frequency of 1 kHz and a frequency in the range from 1 Hz to 10 MHz along two output lines. The MFC is designed to operate in measuring systems based on the VXIbus trunk. In the MFC, a rubidium frequency standard is used as a reference frequency source. Time to reach the mode when the power source of the rubidium standard is turned on, no more than 10 min
-
PCIE-5565PIORC -
Abaco Systems Inc
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
MX1 -
Manncorp
Manncorp’s new MX1 is a high-performance x-ray inspection system designed for real time imaging of multilayer PCBs and dense metal BGAs, μBGAs, and chip scale packages. Its high voltage (80kV), computer-controlled x-ray tube and 35 μm focal spot provide the power necessary for detection of a variety of defects including bridging, voids, and missing balls. The MX1’s standard camera features continuous zoom magnification from 4X to 50X and variable angle viewing up to 45°, and an upgrade to the x-ray tube can boost magnification to 225X.
-
4900 -
BPM Microsystems
The 4900 is powered by the newest BPM 9th generation technology, which delivers the fastest programming speeds in the industry for MCU’s, eMMC HS400, NAND, NOR and Serial Flash devices. BPM 9th generation technology produces 200 MHz signals, allowing each byte of data to transfer in up to 2.5 ns. Up to 9 times faster than competing programmers. 3D Vision option inspects BGA, CSP, QFP, TSOP, SOIC and J-Lead devices for coplanarity, bent lead, pitch, width, diameter, standoff and XY errors.
-
ADLINK Technology Inc.
The Automation Product Software SDK (APS SDK) is an all-in-one solution with an optimized uniform interface to access all supported ADLINK machine automation products. The APS SDK features rich, powerful application-oriented motion functions that co-work with components such as system platform management, field bus communications, general digital input/output, general analog input/output and support for various counters/timers. With ADLINK machine automation series products that support APS SDK, machine makers can build and deploy applications easily and quickly with a universal tool, saving on TCO and enabling faster time to market.
-
NI
The Multi-IDE Bundle provides a LabVIEW and C solution to build applications using multiple development environments. The bundle includes LabVIEW Professional Development System, LabWindows/CVI Full Development System, and Measurement Studio Enterprise Edition. LabVIEW NXG 1.0 the next generation of LabVIEW is included with your purchase of the Multi-IDE Bundle. It minimizes time to measurement with your data acquisition devices and benchtop instruments with engineering workflows for acquiring and visualizing data sets - programming optional. When needed, you can transition to a development approach to customize your test and measurement system.
-
COMBI521EV -
HT Italia Srl
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
TPD Workstation -
Hiden Analytical Ltd.
The Hiden TPD Workstation is a complete experimental system for UHV temperature programmed desorption (TPD) studies. The triple filter mass analyser is configured with a cooled shroud giving the analyser optimum sensitivity with minimum background contributions to desorption products from the sample. A fast sample load lock with sample transfer mechanism is included to provide for rapid sample change. The TPD Workstation features a multiport UHV chamber with heated sample stage coupled to a high precision triple filter analyser with digital pulse ion counting detector for ultimate sensitivity and time resolution.
-
OptoScope SC-20 systems -
Optronis GmbH
The SC-20 streak camera system is characterized by its large detection area of 35 mm x 4 mm and a large usable screen diagonal of 40 mm. Signals are mapped onto the fiber optic input window and measured without the need for optical reduction. In the simplest case, the entrance optics consists of a slit mask that lies directly on the entrance window. In addition, a flexible extension with a shutter, a lens mount or an adjustable slot with coupling optics is possible. The time resolution in the sub-nanosecond range qualifies the camera for many applications in detonics and plasma physics.
-
SparkFun Electronics
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
2000-R -
Bowmonk Ltd.
The Bowmonk 2000-R is our next generation electronic brake meter, featuring a built-in printer, keyboard, GPS receiver, and coming soon built-in Wi-Fi for automatic uploading of brake test results. Significant processing power and on-board storage enables the Bowmonk 2000-R to be customised for various applications. The Bowmonk 2000-R also supports an optional pedal force transducer to measure the force applied to the vehicle's footbrake during braking. Using the pedal force transducer will also identify any "braking delay" - the time between depressing the brake pedal and the brakes being applied.
-
9330 -
Interface Inc.
The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.
-
Um -
Nanometer Technologies
● Test 12 or 24 fiber MT Connectors● Find Endface defects fast● 800x Magnification●Numbered Dial Indicator to quickly identify which fiber you're onThe Um MT Inspection Scope accurately shows defects in your MT 12 or 24 fiber connectors. Quickly view each fiber to save time and money. Our unique Fiber Dial shows which fiber you are inspecting. No more getting lost!The Um MT is compatible with our Eagle Inspect Software. Create reports with images for your MT connectors.
-
Innova-IRIS -
Bruker Optics
This provides researchers a perfect combination of chemical or crystallographic information at high spatial and spectral resolution with the most advanced atomic force microscopy characterization. The Innova-IRIS can be integrated with your choice of a leading Raman system to provide the best opaque sample TERS investigations available today. However you tailor your system, your application will benefit from Bruker exclusive, high-contrast IRIS TERS probes and the best tip preservation and lowest drift, guaranteeing that alignment is preserved even over the optical integration times necessary to interrogate weak Raman scatterers.
