Filter Results By:
Products
Applications
Manufacturers
-
product
ICE 3000 Series
ICE3001
This subsystem is an agile filter for the SATCOM frequency band, capable of acting as either a receive or a transmit filter. It enables simultaneous operation of multiple transceivers in extreme cosite environments. The ICE3001 provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals for either receive or transmit applications. This filter is a highly integrated design incorporating complete Built-in-Test capability. The design has been qualified for military applications. A dual-mount tray is also available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3001.
-
product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
Variable Attenuator
FTBx-3500
Network equipment manufacturers and transceiver manufacturers know that variable attenuators are essential components of their test systems. They look for performance, user-friendliness, complete control of test parameters and advanced programming capability. EXFO’s FTBx-3500 Variable Attenuator combines innovative design techniques, high-quality components and meticulous calibration procedure. Ideal for bit error rate testing and system verification, the FTBx-3500 is the only variable optical attenuator (VOA) that offers a fully remote user interface (UI) and EXFO Multilink compatibility. It is also the only VOA on the market to offer a benchtop unit, which can be controlled remotely or using a touchscreen.
-
product
Off-Card Adapter,
3910-FOFE
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
product
Very High Density Fiber Tap
Flex Tap VHD
Keysight Network Applications and Security
Flex Tap VHD is a modular, very high density fiber tap available, offering up to 36 taps in a 19 inch 1U space, to reduce IT costs while helping ensure availability of security and business critical applications. Network taps (test access points) are a key part of the access layer of a visibility architecture because they are an unobtrusive way to capture monitoring data. They offer comprehensive traffic visibility for network monitoring and security tools that do not introduce points of failure in the network. Ixia has a large variety of network taps on the market today, offering speeds from 1Gbps to 100Gbps, single and multi-mode, as well as different fiber types and support for Cisco bidirectional (BiDi) transceivers.
-
product
Vector Network Analyzer Extenders
VNAX
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
product
ICE 3000 Series
ICE3006
The ICE3006 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in the cosite environment. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the three-port design (LOS and SATCOM). The ICE3006 incorporates extensive Built-in-Test capability and is qualified for airborne applications. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3006. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
Fiber Optic Talk Set
Fiber optic talk set consists of both the fiber optic light source and transceivers, which carry voice over the spare fiber in both directions. When doing the test work, technicians may need remote location communication during the measurement or splicing work, and sometimes radio-based communications may not be suitable because of environmental conditions such as FCC restrictions, etc. fiber optic talk set will function well in such cases, they could utilize the already installed fiber optic link to carry voice communications.
-
product
PXI Vector Signal Transceiver
The PXI Vector Signal Transceiver (VST) combines the flexibility of a software defined radio architecture and RF instrument class performance. You can use the VST to test a variety of cellular and wireless standards, and you can easily expand the VST's three-slot, 3U PXI Express form factor to support multiple input, multiple output (MIMO) configurations. The VST software is built on LabVIEW FPGA, and features several starting points for your application including application IP, reference designs, examples, and LabVIEW sample projects.
-
product
Fiber Optic Test Solution
Eye-BERT Micro 10G
The Eye-BERT Micro 10G is a low cost, easy to use, all-in-one XFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, diagnostic monitoring, and wavelength tuning (per XFP capability). Additionally, with a click of a button, the Eye-BERT Micro 10G will automatically test an XFP module based on the information it reads from the transceiver and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
Quickly & Accurately Validate Any Pluggable Transceiver from 10M to 100G
iOptics
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
product
Wireless Fiber Inspection Probe - WIS 300
Shanghai Fibretool Technology Co.,Ltd.
WIS 300 wireless fiber inspection scope is a WIFI/USB dual-use portable digital fiber inspector. With automated PASS/FAIL and fast images focus functionality, and easy pairing to Android™ and Apple© iOS devices, It can quickly check various patch cords and transceivers, display the fiber end face in PC/laptop/ OTDR/Smartphone etc..digital devices with the USB cable or WiFi connection. Under WiFi mode, it can automatically get the image checked and analyzed. Test results can do the pass/fail judges with IEC/IPC criteria. Fiber images and results can be saved on PC and mobile devices in jpg/pdf/excel format for file records. It’s super light and handy to take anywhere anytime for field tests, operation inspections, and lab research.
-
product
PXIe-5646, 6 GHz, 200 MHz Bandwidth, RF PXI Vector Signal Transceiver
782952-01
6 GHz, 200 MHz Bandwidth, RF PXI Vector Signal Transceiver—The PXIe‑5646 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5646 features the flexibility of a software defined radio architecture with RF instrument class performance. The additional bandwidth of the PXIe‑5646 enables you to test wireless and cellular standards such as 802.11ac 160 MHz and LTE‑A carrier aggregation while leveraging the latest performance-enhancing processing techniques such as digital predistortion.
-
product
PXIe-6591, 12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument
783638-01
12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument—The PXIe‑6591 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe‑6591 takes advantage of FPGA multigigabit transceivers and up to eight TX and RX lanes. In addition to high-speed serial lanes, the PXIe‑6591 features digital I/O signals that support multiple logic families with per line, per cycle direction control.
-
product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PXIe-4139 , ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit
782856-03
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 40 W of DC power. This module features analog-to-digital converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PXIe-4138, 60 V, 3 A System PXI Source Measure Unit
782856-01
±60 V, 3 A System PXI Source Measure Unit—The PXIe‑4138 system source measure unit (SMU) delivers high power, precision, and speed. It is ideal for a broad range of applications including manufacturing test; board-level test; lab characterization with devices such as integrated circuits (ICs), power management integrated circuits (PMICs), and radio frequency integrated circuits (RFICs); and discrete devices including LEDs and optical transceivers. The PXIe‑4138 features 4-quadrant operation. The PXIe‑4138 is a hardware-timed instrument with a high-speed sequencing engine for synchronizing acquisitions between multiple SMUs. The module supports direct DMA streaming between the host PC and SMU, so you can stream large waveforms and measurement data at the full update rate and sample rate of the instrument.
-
product
PXIe-4136, 200 V, 1 A System PXIe Source Measure Unit
783760-01
±200 V, 1 A System PXI Source Measure Unit—The PXIe‑4136 system source measure unit (SMU) delivers high power, precision, and speed. It is ideal for a broad range of applications including manufacturing test; board-level test; lab characterization with devices such as integrated circuits (ICs), power management integrated circuits (PMICs), and radio frequency integrated circuits (RFICs); and discrete devices including LEDs and optical transceivers. The PXIe‑4136 features 4-quadrant operation. The PXIe‑4136 is a hardware-timed instrument with a high-speed sequencing engine for synchronizing acquisitions between multiple SMUs. The module supports direct DMA streaming between the host PC and SMU, so you can stream large waveforms and measurement data at the full update rate and sample rate of the instrument.
-
product
Patch Panel Automation Switch
Echola's Optical Patch Panel Automation switch allows test engineers/system developers to dynamically reconfigure testbed connections from remote. It reduces test configuration time as they don't need to make any physical fiber connections for each set of tests, so more testing can be performed with fewer resources. It provides all-optical connectivity with zero latency and can be used with any protocols and speed. Unlike O-E-O (optical to electrical to optical conversion) switches you don't need expensive transceivers for each port. The all-optical connectivity also allows systems under test to be tested without introducing another variable (ie, another conversion layer which could introduce significant latency). The patch panel automation switch allows users to configure, control and monitor the device from remote using any standard internet browser, a command line interface (CLI) via Telnet or SSH and SNMP v2c. The event notifications are supported through Syslog. It can be automated using TCL based scripts.
-
product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
product
Muzzle Velocity Radars
MVR Series
The MVR Series of Muzzle-Velocity Radars are Doppler-CW transceivers that measure the velocity of viewed objects such as projectiles. They use phase-locked millimeter-wave transmitter-receivers along with an integrated radome-protected antenna to illuminate objects under investigation. An optical boresighting aid provides alignment assistance for the narrow radiation patterns. Reflected signals from the target are received by the antenna and mixed to produce a video output equal to the Doppler spectrum of the target. A low-noise, variable gain video amplifier can drive a 50-ohm cable up to +1 volt output. The video amplifier has a feed-forward DC offset compensation circuit that extends the Doppler frequency response from under 1 Hz to over 2 MHz. An integrated DMM and LCD display on the front panel monitors various test points within the sensor to verify proper operation. The extremely rugged design allows the MVRs to withstand high acousitic shock environments so they can be located in close proximity to the projectile source.
-
product
PXIe-4135, PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
product
ICE 3000 Series
ICE3009
The ICE3009 subsystem is an agile filter for the VHF-L, VHF-H and UHF frequency bands. It allows operation of a number of transceivers in a cosite environment. The VHF/UHF Filter provides multiple poles of RF selectivity to reduce broadband noise in transmit mode of operation and to reduce interfering signals at the transceiver’s RF input in receive mode at Have Quick II/IIa and SATURN tuning speeds. This design incorporates a flexible control scheme that can be configured at the factory for various radio interfaces (ARC-210, ARC-231, ARINC 429, etc.). The design is highly integrated and includes all filters, amplifiers, power supply, transmit and receive switching (including a bypass mode), and Built-in-Test (BIT). A mounting tray is available as an option for easy incorporation on your platform. This system is qualified for military applications. Cost-effective modifications are available on the ICE3009. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
ICE 3000 Series
ICE3005
The ICE3005 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in a cosite environment and is factory configured for an ARC-210 interface. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the two-port design. The ICE3005 also includes a separate audio processor circuit that mitigates popping and drop-outs in the R/T audio that are common in hopping or blanked waveforms. The ICE3005 incorporates extensive Built-in-Test capability and is qualified for military applications. A mounting tray is available for easy incorporation on your platform. Cost-effective modifications are available on the ICE3005. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.