Showing results: 241 - 255 of 596 items found.
-
North Atlantic Industries
The NAI VPX family of power products include a variety of standard features, including continuous Background Built-In-Test (BIT); remote error sensing; and protection against transients, overvoltage, overcurrent, short circuits and over temperature. These intelligent designs also have the flexibility to address special needs. Optional current share is available on main outputs.
-
PC104pPWR12 -
Dynamic Engineering
The PC104pPWR12 power supply provides for the +5, +3.3, +12, minus 12 and minus 5 from a 12V wall mount transformer supply, battery etc. Each rail is fuse protected. The supply uses switching technology to provide high efficiency coupled with low pass filtering to provide low noise and fast response to transient loads
-
ASM_AF | VP 230045 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
ATS310 -
AlazarTech
ATS310 is the best 20 MS/s 12 bit PCI Digitizer available. With its high signal to noise ratio and robust front-end circuitry, ATS310 has become a de-facto standard for motor testing applications. ATS310 has also been used for multi-channel transient recording applications, as it provides one of the lowest cost-per-channel in the industry.
-
Keysight Technologies
Vector signal analyzers combine superheterodyne technology with high speed ADCs and other DSP technologies to provide fast FFT-based, high-resolution in-channel spectrum measurements, demodulation, and advanced time-domain analysis. A vector signal analyzer is especially useful for characterizing complex burst, transient, or modulated signals in aerospace & defense, radar, wireless communications, and avionics.
-
HiRES -
HIGHVOLT Prüftechnik Dresden GmbH
The digital recorders HiRES are used to measure, store, and evaluate signals from up to 64 sources synchronously. Depending on the sensors used voltages, currents, temperatures, mechanical movements and various other signals can be measured. This measurement system features the ability to capture fast transient processes such as those occurring in impulse current tests on electrical devices or during switchgear testing. The system is also capable of measuring semistationary and periodic events such as DC voltage and AC voltage as well as superimposed semistationary, periodic and transient processes.
-
V420 -
Highland Technology, Inc.
The V420 is an 8-channel, isolated, programmable resistance simulator. It uses entirely solid-state simulation to eliminate transient errors associated with relay switching, and provide for monotonic resistance changes. Channels are individually programmable in four resistance ranges, from 5 ohms to 65.5K. Channels can operate from microvolts up to 35V / 50mA. Overload protection and channel error detection are included.
-
MAC-01, -02, -03 -
Compact Power Company
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
28V-SM-CARR-C -
ELMA Electronic, Inc.
The 28VDC carrier card with confirmal coating provides all the connectors necessary for the monitoring and control functions of any Elma systems, and also the power supply filtering required by the noise and transients consistent with MIL-STD-704E.
-
Hangzhou Xihu Electronic Institute
Calibration Device of Transient Earth Voltage PD detector, calibration device of ultrasonic PD detector, calibration device of high frequency PD detector, calibration device of ultra high frequency PD detector.
-
Renesas Electronics Corp.
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Setfos -
FLUXiM
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
TINA-TI -
Texas Instruments
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages and waveforms. TINA''s schematic capture is truly intuitive-a real "quickstart."
-
ASM-BF/2 | VP 230044 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/2 4WD roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-BF/2 4WD is built into the base.
-
44KS3-02 -
North Atlantic Industries
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.