Showing results: 331 - 345 of 809 items found.
-
COMSOL, Inc.
The design and modeling of microelectromechanical systems (MEMS) is a unique engineering discipline. At small length scales, the design of resonators, gyroscopes, accelerometers, and actuators must consider the effects of several physical phenomena in their operation. Consequently, COMSOL Multiphysics is ideally suited for MEMS applications. To this end, the MEMS Module provides predefined user interfaces with associated modeling tools, referred to as physics interfaces, for a variety of coupled physics, including electromagnetic-structure, thermal-structure, or fluid-structure interactions. You can include a variety of damping phenomena in your model: thin-film gas damping, anisotropic loss-factors for solid and piezo materials, anchor damping, and thermoelastic damping. For elastic vibrations and waves, perfectly matched layers (PMLs) provide state-of-the-art absorption of outgoing elastic energy.
-
C100SMR-1CW-6A -
Pickering Interfaces Ltd.
This accessory is designed to allow users to directly terminate a cable to the connector. It is difficult to terminate cable to the 100-Pin SCSI Style Micro-D connector because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
C100SMR-1CR-6A -
Pickering Interfaces Ltd.
This accessory is designed to allow users to directly terminate a cable to the connector. It is difficult to terminate cable to the 100-Pin SCSI Style Micro-D connector because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
40-201-004 -
Pickering Interfaces Ltd.
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
40-201-008 -
Pickering Interfaces Ltd.
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
32-76e -
Testing Machines, Inc.
32-76e coefficient of friction/peel tester uses advanced digital force signaling and high-speed data acquisition software to provide unmatched precision and repeatability in COF and peel testing. Improved features include a color touchscreen display and intuitive software user interface for easy navigation and test method storage. Peel testing capabilities include 180° peel and T-peel measurements.
-
GRL-KIT-DI20 -
Granite River Labs Inc.
The GRL Deep Inspection Kit (KIT-DI20) addresses the gap between expensive, challenging-to-use VNAs and simple functional/continuity tests that are not adequate for high speed interfaces. Now, users without years of signal integrity testing expertise can perform professional measurements with high accuracy to 20GHz with easy-to-use equipment.
-
SafeTest 60 -
Seward Medical
The Rigel SafeTest 60 is a robust, reliable and dedicated medical safety analyzer. It is ideal for testing high volumes of medical and laboratory equipment that does not require patient lead testing, such as beds, hoists, infusion pumps, CPAP's and centrifuges etc. With a large colour display and a colour-coded user interface, it's easy to select the required tests with a single key press, whilst a fast step-through of the test routine makes the testing process speedy and dependable
-
VirtualSANTM -
GigaNet Systems Inc.
VirtualSAN is a high-performance Fibre Channel SAN Emulator that replicates real world network effects such as latency and errors on user traffic in a controlled environment. The VirtualSAN emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualSAN emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
BAT -
Square Peg Communications Inc.
While the BNE is tailored to the terminal development process, the BGAN Application Tester (BAT), is tailored towards application developers and provides a graphical user interface designed to simplify BGAN application testing.
-
soapUI Pro -
SmartBear Software
soapUI Pro is built from the ground up with enterprise users in mind. It''s loaded with advanced technologies and features you won''t find in other testing tools. With an easy-to-use graphical interface and enterprise-class features, soapUI allows you to rapidly create and execute automated functional, compliant web services and load tests. In a single test environment, soapUI provides complete test coverage and supports all the standard protocols and technologies.
-
AT-930DG -
Airfield Technology, Inc.
Fully Automatic OperationAll-Weather CapabilityDifferential GPS Position ReferenceHigh Accuracy and Maximum ReliabilityWindows User Interface SoftwareEasy to Operate and Easy to LearnMinimum Maintenance RequirementsModular System ArchitectureLong-Term Supportability
-
A300 -
CAPRES A/S
The microHALL-A300 is a state of the art tool with regard to key production and process parameters such as high rate of throughput, reliable and reproducible measurements, simple and intuitive user interface, low cost of ownership and high machine uptime secured by easy and efficient productive maintenance procedures.
-
Avionics Interface Technologies
To satisfy ARINC 615/615A data loader requirements in system engineering labs, avionics system manufacturing, and maintenance depot applications, AIT provides data loader software that can be used together with AIT’s full line of ARINC 429, ARINC 664, and Ethernet interface modules and integrated into a variety of host desktop PC systems and ATE environments. The F-SIM-LDR-615 software provides ARINC 615-3/4 data loader support and is compatible with all of AIT’s ARINC 429 interface modules. The F-SIM-LDR-615A software application provides ARINC 615A-1 /2/3 data loader support over Ethernet and ARINC 664 networks and is compatible with all of AIT’s ARINC 664/Ethernet interfaces modules. The F-SIM-LDR-615 and F-SIM-LDR-615A software products include both graphical user interface (GUI ) data loader applications and command line data loaders which are scriptable and can be called from shell scripts, batch files, and python for support of automated load operations.
-
Q-NET™ Navigator -
Teledyne Paradise Datacom
Q-NET™ Navigator is a powerful application for controlling all devices in the network that support a web user interface (such as Ethernetswitches, routers, RF equipment and modems). It’s easy-to-navigate site map provides access to any network device with a single mouse click.