Showing results: 1 - 15 of 498 items found.
-
TOPTEST GmbH
Test stations with USB hardwareHardware control of adapters with USB-I / OFlash and microprocessor programmer
-
6050 -
PRODIGIT Electronics Co, Ltd.
Single Output USB PD USB PD basic version:the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
AUT20135 -
Allion
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
MCCI
MCCI's Test Lab offers quick, cost-effective USB-IF Logo Compliance Testing for low-speed, full-speed and high-speed devices, and for low- and full-speed systems. As a certified logo-test facility, we can save you time, and give you expert advice.
-
AudioConnect -
Listen Inc
AudioConnect is a 2-in, 2-out audio interface specifically designed for audio test and measurement. It offers digital and analog audio in and out, a a 44.1kHz/48kHz sampling rate, USB control, and a power indicator; all other typical soundcard controls that are not used for audio test applications have been eliminated. This makes operation and calibration simple with no room for error.
-
MQP Electronics
The Packet-Master USB-PDA is a USB PD Analyser, for FSK and Baseband variants of Power Delivery.
-
EXC-UNET2/xx -
Excalibur Systems, Inc.
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
S94USBCB -
Keysight Technologies
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
AmpConnect™ ISC -
Listen Inc
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
ASC1553 -
AIM GmbH
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
AudioConnect 4×4 -
Listen Inc
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
UXI-429 -
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
UXI-1553 -
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
3446ACCU -
Keysight Technologies
3446ACCU provides the accessory kit for the 34460A, including the test leads and USB cable.
-
CAMI Research Inc. (CableEye®)
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models. Configuration A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board. Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote.