Showing results: 2116 - 2130 of 2470 items found.
-
Thorlabs, Inc.
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
BKM91 -
Techna-Tool Inc.
Clockwise and/or counter-clockwise rotation of the wand is programmable allowing an optimum adaptation to the machine.The scanning intensity is adjustable in 8 steps. Even rotating drills with small diameters can be checked.The scanning results are display as "OK" or "KO" and signaled by LEDs on the front side of the device.The PROFIBUS is a standard Sub-D 9 pin connection; the USB connection is a USB-mini plug / type B and meets the 2.0 specification.Three digital inputs serve to activate the functions "Teach-in" to learn the position to be scanned, "Start" to initialize the scanning process and "Configurable" for receiving a stop command.Two digital outputs provide the signals for the message "OK" or "KO".The relay contacts are configurable as N/C or N/O connections. They can be set as momentary (valid with start or timed) or latching.Convenient configuration software for programming and setting of tool data is available at no cost.Mini USB for PC connection3 digital control inputs (positive or negative logic) Start and teach signal One configurable input2 relay outputs selectable as N/C or N/O contact Signal all clear message ("OK") Signal error message ("KO") Scanner connection4 LEDs for status display Opening for top hat plug for optional connection to I/O extension module Din rail mounting
-
BKM91PN -
Techna-Tool Inc.
Clockwise and/or counter-clockwise rotation of the wand is programmable allowing an optimum adaptation to the machine.The scanning intensity is adjustable in 8 steps. Even rotating drills with small diameters can be checked.The scanning results are display as "OK" or "KO" and signaled by LEDs on the front side of the device.The PROFIBUS is a standard Sub-D 9 pin connection; the USB connection is a USB-mini plug / type B and meets the 2.0 specification.Three digital inputs serve to activate the functions "Teach-in" to learn the position to be scanned, "Start" to initialize the scanning process and "Configurable" for receiving a stop command.Two digital outputs provide the signals for the message "OK" or "KO".The relay contacts are configurable as N/C or N/O connections. They can be set as momentary (valid with start or timed) or latching.Convenient configuration software for programming and setting of tool data is available at no cost.Mini USB for PC connection3 digital control inputs (positive or negative logic) Start and teach signal One configurable input2 relay outputs selectable as N/C or N/O contact Signal all clear message ("OK") Signal error message ("KO") Scanner connection4 LEDs for status display Opening for top hat plug for optional connection to I/O extension module Din rail mounting
-
EXFO-100 -
Hangzhou Softel Optic Co., Ltd.
* Top user-friendliness: one-button testing, combined with EXFO’s proprietary FTTx software package (macrobend/fault finder, pass/fail indicators)*Multiple options, including power meter, visual fault locator (VFL), fiber inspection probe, printer and IP testing*Fault Finder mode, for quick identification/location of a fiber break*Complete connectivity flexibility: USB stick compatibility and USB cable data download via ActiveSync**Advanced TFT transflective color display, for assured legibility under direct sunlight or in other demanding outside conditions*Handheld, small, lightweight unit: 1 kg (2.2 lb)*Built-in ruggedness for outside-plant usage*Troubleshooting option, enabling in-service, out-of-band network testing *EXFO’s AXS-100 Access OTDR combines the industry’s leading OTDR technology with power meter functiona lities in one powerful handheld unit.Optimized for testing passive optical networks (PON) within FTTx architectures, it offers several wavelength configurations and a wide range of options, for first-class flexibility. Use it at the optical network terminal(ONT), drop terminal or fiber distribution hub (FDH) for FTTH distribution(F2) fiber characterization, troubleshooting and fault locating.
-
CAPA313 -
Axiomtek Co., Ltd.
The CAPA313 is powered by the Intel® Pentium® processor N4200 or Intel® Celeron® processor N3350 (codename: Apollo Lake). This 3.5" embedded board was designed for operational stability in harsh environments with a wide operating temperature range from -20°C to +70°C. It offers a wide range DC input of 12V to 24 for various industrial environments. It also comes with rich I/O connectors, stunning graphical performance and an emphasis on expandability. In addition to one 204-pin DDR3L-1867 SO-DIMM socket supporting system memory up to 8GB, the CAPA313 has one PCI Expess Mini Card slot for 3G/4G, GPS, Wi-Fi and Bluetooth connection. The compact-size embedded board comes with one RS-232/422/485, one RS-232, two USB 2.0, four USB 3.0, eight-channel digital I/O, audio, LVDS, HDMI, VGA (optional) and dual Gigabit LANs with Intel® i211AT Ethernet controller. It also features one SATA-600 socket and one mSATA interface for storage devices. To ensure reliable operation, the 3.5” embedded SBC supports watchdog timer and hardware monitoring features.
-
Extech PQ3350 -
Extech Instruments Corporation
Power measurements and analysis + datalogging of single and 3-phase/3-wire or 3-phase/4-wire systems (up to 52,428 single phase readings or 17,476 3-phase readings). Large backlighting LCD displays up to 35 parameters in one screen. Clamp-on True RMS power measurements with on-screen Harmonics display. Simultaneous display of Harmonics and Waveform. Display of Waveform with Peak Values (1024 samples/period). Analysis of Total Harmonic Distortion (THD-F). Maximum Demand (MDkW, MW, kVA, MVA) with programmable period. Adjustable CT ratio (1 to 600) and VT ratio (1 to 3000). Graphic Phase diagram with 3-Phase system parameters. 3-phase Voltage or Current Unbalanced Ratio (VUR, VIR) and Unbalanced Factor (d0%, d2%). Calculated Unbalanced Current through Neutral Line (In). Capture 28 Transient events (including Dip, Swell and Outage) with programmable threshold (%). Optically isolated USB interface with software to download Waveforms, Power Parameters and Harmonics. Includes 4 voltage leads with alligator clips and retractable plunger clips, 8 AA batteries, universal AC adaptor, software, USB interface cable, and case. Current Probes sold separately.
-
EnTech Taiwan
If you are a hardware developer, using RapidDriver Explorer with just a couple of clicks, you can easily start testing and debugging your USB, ISA, PCI or Parallel Port device. You do not have to perform any additional steps - everything is already done!If you are a software developer, you can write your own application with the help of RapidDriver Developer, TVicHW32 or TVicPort without writing a device driver and being a DDK expert - we have already built-in generic device drivers for you! Our toolkits include many test examples on direct port i/o access, interrupt handling, physical memory access, reading specific hardware registers and USB pipes to help you getting started. We also allow redistribution of drivers and DLL's as part of your software without having to pay royalties.For the software developers, we also offer an option to purchase the drivers and DLL source code. The source code can be directly edited and compiled with MS Visual C/C++ or with the DDK "build" utility.Not sure what product to choose? Compare them by features or contact us.
-
RX200 -
Renesas Electronics Corp.
The RX200 Series offers the best mix of low power consumption and improved performance in the RX Family. It delivers max. of 80MHz CPU operation with 32KB to 1MB of embedded flash memory. RX200 Series offers a wide set of peripherals, including USB, CAN, ADC, advanced security, and IEC60730 appliance safety standard support. The RX200 Series is suitable for industrial equipment, home appliances, office equipment, healthcare products, meters, and so on. Some of the RX200 Series products are tuned for motor control solutions, too.
-
Pickering Interfaces Ltd.
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
RCDAT-30G-30 -
Mini-Circuits
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
Eye Vision Technology GmbH
The ready-to-use systems offer a variety of solutions with smal learning time and just a few clicks of a button in industries such as food and beverages, electronics and in areas such as deep learning, thermography, 2D and 3D image processing. The systems include the EyeVision software solution for free adaptation, as well as the EmSys computer hardware and an industrial camera from one of the supported manufacturers such as Allied Vision Technologies, Basler, Baumer, Teledyne Dalsa, or thermography cameras from Optris or Flir. Both GigE and USB cameras are available for cameras.
-
CPS2000 -
Boonton Electronics
CPS2000 True Average Connected Power Sensors provide USB, LAN and PoE capabilities to enable easy RF power measurement of modulated and CW signals from 50 MHZ to 8 GHz. Compatible with Windows and Linux systems, CPS2000 sensors include all the necessary drivers for programming through SCPI, IVI and LabVIEW. Connectivity and compatibility, combined with 60 dB dynamic range and 100 measurements per second, CPS2000 sensors are the ideal solution for lab, field, production test, ATE remote monitoring and embedded environments.
-
W-IE-NE-R, Plein & Baus GmbH
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which results in 80 up to nearly 500 individually controlled channels per mainframe. Built in a modular way MPOD consists of the mainframe / bin, a front side plug-in controller with Ethernet and USB ports, a fan tray and a power supply which is located in the back.
-
F125 -
Atelier Robin Inc.
The F125 square wave frequency generator replaces our F150/155/105 frequency generators. It is a completely new design with many new features. The main one being that it can run standalone up to 1500 program files copied from a PC or Mac. It is also possible to connect the F125 to a computer via a USB port and control it with the F100 3.0 software for MS-Windows in the same way our F150/155/105 operate from a PC. Program files written for our current F150/155/105 are compatible with the new F125.
-
Maynuo Electronic Co.,Ltd
*Low ripple and low noise*High resolution and accuracy (0.1mV/0.01mA)*Built-in high-accuracy 5 1/2 voltmeter and milliohmmeter*Supporting high-accuracy and dynamic programming output*High-luminance VFD screen with two lines& four channels display*Intellegent fan system fan will be automatically initiated according to the temperature*Supporting remote voltage compensation and multidata storage*Supporting external trigger input and output*Power-on-self-test, software calibration and standard rack mount*Using standard SCPI protocol*Communication mode: RS232/RS485/USB.
