Showing results: 166 - 180 of 671 items found.
-
W-IE-NE-R, Plein & Baus GmbH
NIM "Nuclear Instrument Module" is the oldest and simplest nuclear electronics standard. Created in 1969 with AEC report TID20893 (Dec 1969), it defines a powered bin and plug in modules. NIM is the perfect standard for small and flexible setups for high resolution measurements with analogue electronics (amplifier, high resolution analog to digital converter, timing electronics as well as for low / high voltage supplies.
-
CX-8000 -
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
onTAP’s THREE TAP CONNECT JTAG -
Flynn Systems Corp.
Connect the TAP CONNECT JTAG Controller to your application with either the Xilinx ribbon cable, flying leads, or Altera style adaptors. The onTAP TAP CONNECT Controller automatically senses and adjusts to target I/O voltages and interfaces to devices operating at 1.8 to 5.0 VDC for the standard controller, or 0.99 to 3.6 VDC for the low voltage controller, using the VREF voltage from the target chain. If there is no VREF available, you can set the voltage for the target application from the TAP CONNECT Controller. This facilitates easy configuration to many different JTAG ports, which is helpful in design and manufacturing.
-
Gardner Bender
Manual or auto ranging with easy to read digital displays. A test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
F8200 -
Manta Test Systems
Use the F8200 Power System Simulator for testing single-phase conventional schemes, digital protection systems, and more. This four-module F8000-series instrument is available in four standard configurations of HVA Current, HVA Voltage, and Low-Density Logic I/O modules.
-
U270xA -
Keysight Technologies
Roughly the size of a paperback book, these low-cost USB oscilloscopes make it easy to perform essential measurements — waveforms, voltage, current, resistance, and more. Inject standard or arbitrary waveforms into the systems or devices you’re testing with Keysight USB oscilloscopes.
-
KT3201 -
Ketai instrument (kunshan) Ltd.
KT3201 KT3202 KT3203 KT3204 four high-precision multimeters are specially designed for European student watches.It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT3203 is a specially designed AC and DC ammeter .KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
PE-100 -
Pansco, Ltd
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
CSS61000-11 -
Lisun Electronics Inc.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
Algodue elettronica
Additional voltage and current measurement channels in comparison with other standard three-phase devices.Current inputs for CTs or for clamps to grant an accurate current measurement.Continuous monitoring of the power quality and Class A certified measurements for voltage characteristics.Simultaneous recording of events, Min/Avg/Max LOG and energy counters.Several possibilities for instrument data transmission: Ethernet, Modbus TCP, 3G network.User-friendly instrument web interface with multilingual pages.
-
VDS-1120DX -
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
ALT Series -
High Voltage Inc.
HVI produces AC voltage testers that perform boom and liner testing, with models available up to 300 kV AC for boom testing and 10 kVA for liner testing. The ALT Series is designed for AC voltage testing aerial lift devices. The standard models available are rated 120/60 kV AC, 200 kV AC, and 300 kV AC, rated up to 7 kVA.
-
Tektronix, Inc.
Passive voltage probes ship standard with most oscilloscopes and provide a low cost, general purpose probing solution. Generally, these probes lack the performance of an active voltage probe but provide the ruggedness and wide dynamic range suitable for visualizing signals over a broad range of applications. Tektronix has released a new class of passive probes that redefine performance in the passive probe product category.
-
Model PMD-503E -
tecsis LP
Programmable meter display, 7-segment, 0.31", 5 digits, Panel mount, 1/8 DIN standard, larger cutout for optional metal case, for pressure/load sensors, 0.5 to 20 mV/V strain gage, optional voltage DC or AC, Current
-
Model PMD-50E -
tecsis LP
Programmable meter display, 7-segment, 0.56", 5 digits, Panel mount, 1/8 DIN standard, larger cutout for optional metal case, for pressure/load sensors, 0.5 to 20 mV/V strain gage, optional voltage DC or AC, Current