Showing results: 1 - 15 of 24 items found.
-
VDS Series -
Noise Laboratory Co.,Ltd.
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
VDS-2002 -
Noise Laboratory Co.,Ltd.
NoiseKen's new VDS-2002 offers easy and accurate test and following features: Dip, swell, interruption and variation tests up to 16A 240V single-phase AC, interruption test up to 125V DC, preset levels 0%/40%/70%/120%, open and short mode selection for interruption and optional Windows software.
-
Datexel
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
CSS61000-11 -
Lisun Electronics Inc.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
VDS-1120DX -
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
FE-W7 -
Ceibo Inc.
* Emulates Winbond W77xxx or W78xxx Microcontrollers * 125K Code Memory * Real-Time Emulation * Frequency up to fmax at 1.8V to 5.5V * Wide Supply Voltage Support * MS-Windows Debugger For C And Assembler * Emulation Headers for PLCC, QFP and DIP * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Datexel
Datexel has a large range of Signal Conditioners. We manufacture Thermocouple Transmitters, that are either Head Mounted, Din Rail and we even have an OEM version that can fit inside an enclosure smaller than 1" x 1/4". These Temperature Transmitters are PC programmable or DIP Switch programmable. Some are isolated and accept input from various sensors such as RTD's, Thermocouples Voltages, Current, Resistance and Potentiometers. They have current outputs and we even have Temperature converters that have voltage outputs.
-
Frequency Devices Inc.
precision band-pass and band reject (notch) active filters that provide high performance in a compact 32-pin DIP package, with a broad range of fixed center frequencies (fo) from 1 Hz to 100 kHz. Each filter type features a neartheoretical amplitude/phase response along with lowoutput voltage noise enabling these filters to achievea 10,000:1 or better dynamic signal range.
-
cPCI-3548 -
ADLINK Technology Inc.
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
Datexel
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
LS6100 -
Lisun Electronics Inc.
Designed to measure the aging-life and color comparisons of 260pcs DIP LED. • 260 separate constant current supply • Aging functions: constant current, impact pulse, on-off mode • Range of forward voltage(VF): 5.0V • Range of forward current(IF): 1) constant current: 0-100.0mA 2) Impact pulse: 0-200.0mA • Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99% • Range of on-off circle: 0-9999H59M59S • Range of on-off times: 0-9999times • Range of aging time: 0-9999H59M59S
-
RA 19 -
Kepco, Inc.
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
PAS 9716/AO-SMT -
Precision Analog Systems Co.
The PAS 9716/AO provides sixteen channels of sixteen-bit Analog Output. The card can be used in VME systems with A16, A24, or A32 addressing, and data writes of 16 and 32 bits are supported. DIP switches are used to configure the width of the address bus. The data bus width is specified by the instruction. Highspeed voltage output DAC’s, with 6 uSec typical settling times are used on this card .The DAC output signals are available on a 37 pin D connector mounted through the front panel. Two digital output signals are also provided on the output connector.
-
Series C75-2 -
Teledyne Defense Electronics Relays & Coax Switch
Series C75-2 solid-state relays are packaged in a 16-pin DIP, with surface-mount or through-hole mounting available. They utilize a power FET switch that is protected against overload and short-circuit currents. 2S versions provide an open-collector trip status feedback to the relay’s control side. 2SH versions add an internal transient voltage suppressor for inductive loads.MSL 6C75 relays are controlled with 4.5-5.5VdcC = Through-hole mount SC = Surface mountAvailable options include:C75-2 1A, 60Vdc Load; short-circuit protectionSC75-2 1A, 60Vdc Load; short-circuit protection C75-2S 1A, 60Vdc Load; short-circuit protection and trip satusSC75-2S 1A, 60Vdc Load; short-circuit protection and trip status C75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip statusSC75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip status
