Showing results: 2521 - 2535 of 3668 items found.
-
FE50DTR -
Rohde & Schwarz GmbH & Co. KG
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
AMS -
Rohde & Schwarz GmbH & Co. KG
The R&S®AMS aerial monitoring system is a payload for drones that provides monitoring and analysiscapabilities for transmissions that are difficult to reach by conventional mobile or handheldsolutions. Typical applications include monitoring of microwave links and interference hunting. The R&S®AMS is independent from the used drone and can operate in an interactive mode requiring a pilot and a monitoring technician as well as in an automatic mode performing predefined measurement tasks requiring only a drone pilot.
-
CMW290 -
Rohde & Schwarz GmbH & Co. KG
The R&S®CMW290 is the ideal test solution for the integrated wireless communications modules used in laptops, data cards, wearables and various IoT products. The R&S®CMW290 offers functions tailored to these applications within the R&S®CMW product family. The tester provides network emulation (signaling mode) as well as generator and analyzer functions for the supported cellular and non-cellular standards including GNSS and broadcast technologies.
-
Saturn -
Teradyne, Inc.
The Saturn HD is the industry leader in 3.5” Near-Line Hard Disk Drive (HDD) testing. It provides maximum throughput while minimizing factory floor space and power consumption. The system is designed to perform single insertion of SSW, BDSW and Burn-In as well as drive configuration. Using Saturn HD on the production floor will reduce drive build times, enable greater responsiveness to data center demands and lower test costs per HDD unit.
-
R1L-BR -
TEGAM Inc.
The R1L-B series Ohmmeter/Bonding Tester is a digital microohmmeter designed to measure resistances from 10 to 20 . It is used in applications such as metal bonding, switch, circuit breaker, circuit resistance and other contact and connection resistance tests as well as higher resistance measurements for circuit analysis and resistor testing up to 20 . The instruments utilize the four-terminal, Kelvin technique to eliminate errors caused by the resistance of the leads. Resistance readings are viewed on a 3 1/2 digit display,
-
iWave Systems Technologies
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
781352-01 -
NI
Master/Slave, C Series PROFIBUS Interface Module - The cRIO-PB-MS connects NI programmable automation controllers (PACs) to PROFIBUS industrial networks as powerful masters or slaves. The interface includes the NI‑PROFIBUS for CompactRIO instrument driver for human machine … interface (HMI) and SCADA applications, as well as a graphical networking Configurator software. You can perform PROFIBUS device automated test using these interfaces. The cRIO-PB-MS is compatible with only CompactRIO systems.
-
ZETLAB Company
CPB analysis is used for fractional octave spectral processing of signals coming from the input channels of FFT spectrum analyzers (in real time or recorded time realization view mode), as well as for viewing various spectral characteristics of signals. CPB analysis is used for separating signals into basic constituents in the frequency area in 1/3-, 1/12-, 1/24-octave spectral bands. The software is used for noise spectral analysis within the scope of acoustic and vibrational measurements.
-
DVB-S/S2 -
TestTree
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-S and DVB-S2 signals before uplink and after downlink, through its RF inputs (up to 4 in 1RU), as well as baseband transport before satellite modulator and after IRD, through its ASI and IP inputs.
-
784175-01 -
NI
The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
780985-01 -
NI
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
Staubli Group
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
JY6611S -
Kingrun Instrument Co., Ltd.
JY6611S transformer oil breakdown tester adopts completely new electromagnetic compatibility concept(EMC) which designed to avoid tester crash accident during testing, and also can still work well in high magnetic field.JY6611S also use advanced voltage breakdown control technology which will keep breakdown energy in a very low level, that will avoid pollution to oil sample during testing and make sure the test result are accurate and reliable.
-
M9146A -
Keysight Technologies
The M9146A contains two 1x4 RF switch multiplexers in a single PXI module. It offers 50 Ω inputs with bi-directional switching up to 3 GHz. This module features excellent insertion loss and VSWR for better RF signal integrity as well as outstanding dynamic range for routing RF signals into your measurement equipment. Each path is designed to ensure repeatable RF performance. Connections are made through easy, snap-on SMB connectors.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
