Showing results: 826 - 840 of 1041 items found.
-
M8K1760Px(S) -
Excalibur Systems, Inc.
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Logic Pirate -
Seeed Technology Inc.
8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files
-
Eltima Software
With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.
-
xiD -
XIMEA GmbH
*Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling
-
WT3000 -
Lisun Electronics Inc.
• It has 8 windows to display each parameter of input and output characteristics • Frequency response for testing input current up to 1MHz, suitable for precise testing of various kind of electronic ballast • WT3000 has expanding analysis for envelope wave. • Symmetry analysis for envelope wave’s crest factor of lamp current • Sampling at ultra-high speed, dynamic analysis single frequency curve, highest sampling frequency is up to 10MHz • Portable with built-in chip micro-processor, particular suitable for development and spot production • RS-232C standard interface can be connected to PC, English version software can run in WinXP or Win7
-
IXI Technology
The IXI Technology Data Display Computer™ (DDC) is a general-purpose computer ideally suited for military, aerospace, or industrial applications. It is a direct replacement for the OJ-454(V)/UYK Data Display Computer and ORTSNET Workstation. It is designed to run the Navy’s ORTS Network Emulation Terminal (ORTSNET) software, providing status, maintenance direction, fault reporting, indication and display, and readiness assessment of the AEGIS Weapon System. While rugged in construction, the DDC makes maximum use of commercial off-the-shelf components so that it can be readily configured for specific applications. It will compute with Windows, Linux, Solaris, and other operating systems.
-
CTS Series 3.2 -
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.
-
VX1725 / VX1725S -
CAEN S.p.A.
The VX1725S family comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1725S is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window).
-
HydroSweep DS -
Teledyne Marine RESON B.V.
The HydroSweep DS is a deep water multiebeam echosounder ideally suited for seabed mapping in deep water up to full ocean depth based on a sonar frequency between 14 kHz to 16 kHz. Beside bathymetric depth information from 10 m to more than 11,000 m, sidescan data and backscatter data for seabed classification are acquired. The HydroSweep DS does not only gather sea floor information, but also uses adaptive bottom tracking windows to identify sonar targets in the water column and can be optionally operated as a parametric sub-bottom profiler without additional transducers and electronics.
-
Extech TH10 -
Extech Instruments Corporation
Featuring a temperature range of -40 to 158°F (-40 to 70°C) with an accuracy of ±1°C/1.8°F, the Extech TH10 captures and stores up to 32,000 temperature readings. Users can select data sampling rates of 2s, 5s, 10s, 30s, 1min, 5min, 10min, 30min, 1hr, 2hr, 3hr, 6hr, 12hr and 24hr. The TH10 also has user-programmable high/low alarm thresholds and status indication via red/yellow and green LEDs. Comes with a 3.6-volt lithium battery, a protective USB cap, a mounting bracket, Windows compatible software for analysis, and user manual.
-
CDQC -
Teledyne Analytical Instruments
Teledyne’s Carbon Dioxide Quality Control (CDQC) system offers an integrated package to continuously monitor impurities in carbon dioxide (CO2). The plug-and-play design allows for the user to select only the gases and features of interest to maximize cost benefit and space.Front door viewing windows allow for view of all analyzer displays, flow and pressure settings. Stainless steel tube fitting connections and NPT or metric electrical ports as required are conveniently located in a central location for ease of access. Sample conditioning, utility gas provisions and integral calibration gas solenoid valves are standard.
-
MESA-7220V2 -
HORIBA, Ltd.
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
CAN-Logger100 -
ICP DAS USA, Inc.
The CAN-Logger100 is a high-performance smart CAN bus data logger with one CAN port that can help collect data and process on a CAN bus network easier and quicker. The powerful CPU of the CAN-Logger devices provide the accurately time-stamp for each CAN message and support storage media like SD card or SDHC type flash to save CAN messages, which helps users easily analyze and diagnose the CAN Bus network. Providing great portability, the CAN-Logger100 is powered by USB interface or M12 connectors of CAN bus interface. The CAN-Logger100 device uses the standard USB HID driver of the Windows system.
-
National Technical Systems
Forced entry testing is conducted on building envelope and system components such as doors, windows, wall panels and escape hatches as an attempt to penetrate or distort an edge in order to disengage a fitting or device from its mountings and allow access. The US Department of State has developed a standard that all building envelope and system components used in both domestic security and overseas facilities are required to achieve. NTS conducts all forced entry test in their DOS approved facility in accordance to the SD-STD-01.01 standard. All testing is witnessed by DOS personnel with NTS providing reports on all tests performed.
-
PCIEC4L-MA4 -
Alta Data Technologies LLC
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
