Showing results: 1126 - 1140 of 1191 items found.
-
Tektronix, Inc.
*5½-digit resolution to 8½-digit resolution DMMs*6ppm basic voltage measurement accuracy on the 8½-digit DMM for calibration laboratories*Fast, 1 Msample/s sampling speed to capture complex, low level current profiles from IoT devices or other wireless devices*Sensitivity of 1 µΩ and 1 pA to test low power devices for research, design, and manufacturing test*A wide range of measurement functions such as DC and AC volts, DC and AC current, two- and four-wire Ohms, continuity, frequency, period, RTD, thermistor, and thermocouple temperatures, diode test, and capacitance*Numerous interface options including LAN/LXI, USB-TMC, GPIB, and RS-232 for data acquisition and automated testing*Intelligence to execute tests and create customized measurements with minimal PC interaction*Measurement expansion up to ten channels
-
Pulse Electronics
Pulse’s External and In-Building antenna solutions are used worldwide, providing organizations and Public Safety entities with the coverage that they rely on every day. In both portable and fixed designs, for a variety of frequencies UHF, VHF, 4G LTE/5G, WiFi 6e, GNSS and more, our External/In-Building antenna products are critical to a network’s functionality. Our V-Thinity and Clarity series antennas offer sleek low profile, aesthetically pleasing designs that can be implemented in a variety of solutions throughout in-building applications. Our portable antennas are designed and tuned specifically to work with your handheld radios and devices of choice. Pulse’s capability to adhere to Passive Intermodulation (PIM) requirements while maintaining carrier grade quality has made us a leader in the In-Building market. You can search through our selection of catalog External/In-Building products using the table below to extend your wireless coverage.
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
AWA-0142 -
Anokiwave Inc.
The AWA-0142 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0135 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0135, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0142 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
AWA-0134 -
Anokiwave Inc.
The AWA-0134 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0134 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
DCR822 -
Lectrosonics, Inc.
The DCR822 compact 2-channel digital receiver with analog and digital audio outputs utilizes the Lectrosonics signature digital architecture with remarkable audio quality and ultra-low latency. The receiver includes an extended operating range rivaling the best analog and Digital Hybrid Wireless® systems with continuously tunable tracking filters covering 470.100 - 614.375 MHz. The innovative Vector Diversity technology raises the bar for digital transmission integrity with two RF front ends per channel, and a unique phase-matching system. The extremely robust RF front ends of the receiver will hold up in severe RF environments and close carrier spacing, whether analog or digital. The DCR822 has a flexible output routing scheme, allowing a variety of applications including Talkback. And, a digital recorder at 24 bits, 48 kHz is included – and records up to 4 audio tracks on a front-mounted microSD card.
-
62000L Series -
Chroma ATE Inc.
The Chroma 62000L Series Programmable DC power supplies have low noise linear performance and fast transient response. The units have many unique functions that are targeted for overall automated test system integration, automotive power electronics MCU/ECU, power semiconductors, wireless communications, etc. The 62000L Series is a high quality yet cost effective programmable DC Source, designed to meet the stringent requirements of the next generation of power electronics. The GPIB and USB control interfaces come standard with the 62000L Series, no additional purchase required. The 62000L Series can be easily remote controlled via either of these two interfaces. The 62000L weighs less than 2.5 kg, and its case measures 214.6W * 88.6H * 280D mm. Its light weight and compact size makes it easy to handle and stack safely.。
-
IFB112 -
Axiomtek Co., Ltd.
The IFB112.supports the low power consumption NXP (Freescale) i.MX6UL ARM® Cortex™-A7 528MHz SoC. The design concept of IFB112 is aiming to meet the demands of mission-critical applications. The gateway controller with IP30-rated aluminum and steel enclosure supports an extended operating temperature ranging from -40°C to 70°C, a wide voltage range of 9V - 48V DC power input with terminal block, and has been designed to withstand vibration up to 5G. For system integrators with wireless communication needs, the IFB112 has one PCI Express Mini Card slot, one SIM card slot, and two internal antennas. It supports one serial port, two LANs and one CANbus port to enable fast and efficient data acquisition and communication. Its digital I/O port provides users with a convenience of digital devices connection.
-
WISER 4000 -
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
iBA -
Kaelus
Passive Intermodulation (PIM) occurs when multiple RF signals encounter defects in materials or workmanship in an RF path. These defects behave like a mixer causing noise to be generated at mathematical combinations of the original carrier frequencies. PIM interference that falls in the receive band of a wireless system elevates the noise floor resulting in high dropped call rates, call blocking, slow data transmission speeds and decreased system capacity.Kaelus is the industry leader in Passive Intermodulation test solutions. Since 1996 Kaelus has supplied RF equipment manufacturers around the world with precision IEC compliant test equipment to perform this critical test. From initial product design through high-volume manufacturing, Kaelus offers a wide range of PIM test solutions that enable equipment manufacturers to quickly and confidently verify the performance of their products.
-
End-of-line Tester UTP 9010 RF -
NOFFZ Computer Technik GmbH
The UTP Series 9010 is a scalable test series available in a variety of feature-rich variants and many designs. The UTP 9010 RF function tester shown here as an example is suitable for tests with a medium number of channels and complexity. It is designed for parallel testing of two or more test items. The measuring instruments used are used alternately for several test items. Due to its compact design and construction as a modular system, this powerful tester can easily be expanded to larger numbers of channels.The integrated HF test chamber UTP 5070 developed by NOFFZ allows an independent shielded test. It can be operated manually or fully automatically by a robot .The basic version of the UTP 9010 series is an ideal system for functional and end-of-line tests and is already preconfigured for this purpose. The RF tester presented in the example is used in particular to test infotainment and eCall modules in the vehicle as well as IoT products with wireless technologies.
-
66319B -
Keysight Technologies
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
KT RFCT 2400 -
Konrad Technologies GmbH
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
Microchip Technology Inc.
To address the needs of the smart energy market, we offer a platform that incorporates application-specific solutions as well as standard microcontroller, microprocessor, security, memory, wireless and power-line connectivity devices. This smart energy portfolio offers you best-in-class feature sets and performance for designing equipment for the smart grid. The smart meter architecture requires different levels of integration depending on system architecture partitioning, project timelines and the level of flexibility needed to address the requirements of different geographies and utility companies. Our platform provides a unique multi-level architecture built around a multi-core solution as illustrated below. A variety of devices can be used as building blocks for your smart meter design. These include metrology sensing (analog-to-digital conversion); metrology digital signal processing; application, communication and security processing as well as connectivity to area networks in homes neighborhoods.
-
Corvalent Corporation
Our line of CorSense™ wireless sensors are capable of monitoring air quality, humidity, barometric pressure, temperature, current, vibration, and more.Built with a rugged case and able to withstand harsh industrial environments, these sensors are all tested to ISO standards. When paired with CorGateway, sensors gather and transmit data securely to a Corvalent CorEdge computer anywhere from 2 to 28 miles away.Extremely energy efficient, CorSense IoT sensors can also run on batteries for up to 2 years.9 different sensor options:-Smart Vibration & Temperature Sensor -CO2, Temperature, Humidity & Particulate Matter Sensor -CO2, Temperature & Humidity Sensor -Temperature, Humidity, Pressure & Air Quality Environmental Sensor -Precision Pressure Bidirectional Differential Sensor -Pressure Bidirectional Differential Sensor -AC Current Monitor -Vibration & Temperature Sensor -Predictive Maintenance Module Sensor
