Showing results: 2866 - 2880 of 4968 items found.
-
ESR70 -
Peak Electronic Design Ltd.
The Atlas ESR provides instant measurement of a capacitor's ESR and it's capacitance value. Using the supplied gold plated probes (removable), the Atlas ESR can measure ESR down to a resolution of 0.01 ohms, up to 40 ohms. It can even measure ESR for capacitors that are in-circuit. Measurements are made at the industry standard frequency of 100kHz. Probes are now removable, allowing 2mm compatible probes to be fitted. Audible alerts are produced for various ESR levels allowing you to perform many tests in succession without having to look at the display.
-
85553A -
Keysight Technologies
This cable provides the bias voltages and control signals for operation of the 40 GHz CalPod modules. This cable is supplied with the 85540/41/42A CalPod modules.
-
190656-01 -
NI
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
190656-02 -
NI
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
MW802 -
Milwaukee Instruments
This Milwaukee 3-in-1 combo meter allows you to measure pH, EC (conductivity) and TDS with a single meter and one single probe.
-
72-9180 -
Tenma
The 72-9180 is an AC/DC Clamp Meter Leads, use almost any DMM as a clamp meter for current testing up to 400A and current displays as an easily translated voltage reading.
-
GM8019 + GM83001E -
UC Instruments, Corp.
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
-
763000-01 -
NI
Power Cord, AC, U.S., 120 VAC, 2.3 meters
-
The Swain Meter Company
The SEA CLIP™ by Swain Meter is a high-quality, hydraulically actuated clamp-on DC ammeter for ROV. It is useful for measuring DC currents in subsea cables, cathodic protection systems, and subsea pipes up to 4” in diameter. The SEA CLIP™ can be used with an optional 200-foot cable to a topside meter, or in concert with the Aqua MER™ subsea meter at depths up to 6900 feet of seawater.The Aqua MER™ ROV meter is based on Swain’s proven MER2™ technology, specially adapted to the demanding requirements of the subsea environment and updated to provide RS-485 communication over twisted pair, or fiber optic data transmission protocols.
-
SY8126 -
Hong Kong Songyang Industrial Ltd.
SY8126 single phase Energy Meter Test Equipment is a new generation, high precision, energy meter calibration equipment. It uses the international’s most advanced technology and components available in 90 decade. The equipment works under the control of keyboard or remote computer.
-
SY8320E -
Hong Kong Songyang Industrial Ltd.
Close-link and ordinary calibration both can be used, ordinary calibration can be used to test single/three phase active and reactive energy meter (up to 0.5 class),close-link calibration can be used to test single/three phase active and reactive energy meter (up to 1 class)
-
Loresta AX -
OAI
The Loresta AX Resistivity Meter a handheld unit measures the low resistivity of samples with consistent accuracy. This resistivity meter measures resistivity using a wide variety of probes. The Loresta AX uses a standard RCF that enables the user to input other RCF''s if known.
-
HD2110L -
Delta OHM S.r.L.
HD2110L is an handheld integrating sound level meter performing either spectral or statistical analysis.
-
LAQUAtwin EC-33 -
HORIBA, Ltd.
The only pocket meter that directly measures conductivity and total dissolved solids (TDS) in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.