Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 3541 - 3555 of 4469 products found

  • HIPOTS (High Voltage Testers) / AC Hipots

    5 kV Digital - UDEYRAJ ELECTRICALS PRIVATE LIMITED

    Panel mounted controls & indicators. Variable from zero to 5 kV. Digital kV and leakage mA meter.

  • HIPOTS (High Voltage Testers) / AC Hipots

    5 kV Analog - UDEYRAJ ELECTRICALS PRIVATE LIMITED

    Variable from 0-5 kV. Multi-range kV & mA meters. Zero start interlock protection.

  • Power Sources

    MTE Meter Test Equipment AG

    The SPE System is a three-phase electronic voltage- and current power source used in the testing of electricity meters or other devices.

  • Signal Analyzer

    IT-083 DVB-S/S2 - Planar, llc

    A configuration of IT-08 Multifunction TV Meter designed for adjustment of reception systems of satellite analog and digital (DVB-S and DVB-S2) TV signals.

  • Single mode Fiber Optic Test Set w/FC Interface

    5680-FC - Greenlee Communications

    Includes: Optical power meter, 1310/1550nm Laser source w/FC connector, FC/PC SOC adapter, and carrying case

  • Singlemode Fiber Optic Test Set w/ST Interface

    5680-ST - Greenlee Communications

    Includes: Optical power meter, 1310/1550nm Laser source w/ST connector, ST/PC SOC adapter, and carrying case.

  • LED TEST SET

    PX-D102 - Photonix Technologies, Inc.

    The TECHLITE series of test sets allow fiber technicians to perform precise optical testing in the field. The meters, when operated in absolute power mode, are used to determine the level of optical power being emitted from a transmitter. In relative mode, the meters are used with the included source to perform fiber loss measurements or splice tuning operations. The TECHLITE meter, in relative measurement mode, will store the zero reference reading for all four wavelengths independently in non-volatile memory. This allows all zero references to be taken at one time and also allows the unit to be turned off while moving between locations preservebattery life. The TECHLITE meters utilize a graphic LCD screen to create unusually large and easy to read numbers as graphics to indicate power levels.

  • Pointer Insulation Resistance Tester

    HT2533 - Wuhan Huatian Electric Power Automation Co., Ltd.

    With the rapid development of China's power industry, electrical equipment preventive experiment is an important part in protecting the safety operation of power system and maintenance. Insulation diagnosis is an important method to detect insulation defects or failure. Pointer insulation resistance tester is the special instrument to measure insulation resistance. JJG662-89 "insulation resistance meter (megger)" approved in May 1990 requires that insulation resistance meter is one of compulsory verification instruments. Nowadays the development trend of electrical equipment (such as transformers, generators, etc.) is that high capacity, high voltage, diversified structure and better seal. So insulation resistance meter (pointer) itself must have the characteristics such as large capacity, strong anti-interference ability, diversified measurement indexes, accurate measurement results, easy and fast measurement process, easy to carry and so on. The instrument produced by our company is equipped with ultra-thin taut suspension meter.

  • Surface Resistance Checker

    AS385 - Velleman, nv

    For Surface Resistivity Readings: Place the meter on the surface being tested and press the test button . If the LED showing 10^6. is illuminated, the surface being tested has a surface resistivity of 10^6 ohms per square or less. If the LED labeled insulative, is illuminated, the surface under test has a surface resistivity is greater than 10^12 ohms per square. (Be sure the ground wire is not connected through the ground jack when surface resistivity measurements.) For Resistance to Ground Readings: Place the meter on the surface being tested. Connect the meter to a known ground through the ground jack. When the ground wire is connected through the ground jack, the meter will not measure surface resistivity. Press the center button and the illuminated LED will indicate the resistance 10^5 ohms or less. If the LED shows insulative ,the resistance to ground of the surface under test is greater than 10^12 ohms.

  • Water flow test rig

    SHANGHAI POWOO INDUSTRY

    System features:Manual type Water Meter Test Bench with Scale system It can test according to ISO 4064 or OIML R49 For the same lot of water meters, you need to have parameters setting only for one time.WM5-DN15-DN25 for 1-5 meters in series.Adopt TCS Series Electronic Balance from the largest electronic scale sensors manufacturer in China. The scale has virtues of high precision, high stability, easy operation, convenient information collection etc.It can have pressure testing for water meter.The equipment has water circulated function, and has virtues of low noise, high stability.It can adapt to all kinds of mechanical water meters verification, and is very flexible.The equipment is made of 304 stainless steel and copper.Sufficient spares for wearing parts are (like o washer etc).Low fault rate, convenient repair.With full technical documents.

  • Distribution Amplifier

    PB2X8 - Audio Technologies, Inc.

    The PB2X8 "Press Box" provides two high quality XLR inputs, which can be individually switched or mixed into any of eight isolated line level outputs. Each input may be individually switched for microphone or line levels with phantom power and low cut filters available for the microphone inputs. A calibrated test tone oscillator can be switched in place of either input for system test and level checks.A bargraph LED display meters any of the eight outputs or either input. The meter may be switched for 0VU indication at nominal outputs of +4, +8 or +18dBm with the top position an effective headroom indicator. A headphone output follows the meter selection for audible monitoring.

  • Conductivity / TDS / Salinity

    Sper Scientific

    The amount of mineral and salt impurities in the water is called total dissolved solids (TDS). TDS shows how many units of impurities there are for one million units of water. One way to measure impurities in water is to measure the electric conductivity of water. Absolutely pure water is a poor conductor of electricity. Water shows significant conductivity when dissolved salts are present. Over most ranges, the amount of conductivity is directly proportional to the amount of salts dissolved in the water or Salinity. Four basic styles of Conductivity / TDS / Salinity meters are available for varying applications: Pens, Portable Meters, Data Loggers, and Benchtop meters.

  • True Three-Phase Test Systems

    2350 Series - Radian Research, Inc.

    The Model 2350 sets the benchmark for precision and functionality in today’s meter testing industry. This versatile testboard provides fully ANSI compliant testing using either a single or three-phase voltage and current up to 50 Amps. Three-phase power combined with the file/graph capabilities of Winboard™ software gives you the power to test today’s meters with any combination of voltage phase angles, current imbalances, phase angle imbalances and frequencies in .001Hz steps. With the revolutionary Turbo Test™ option, you can run simultaneous series and element tests and increase the productivity of your meter shop five-fold*.

  • Phase ID Systems

    Bierer & Associates, Inc

    LED Meter Probe allows the user to take Real time Phase Angle readings along with AC nominal voltage readings. A PD800W LED Meter Probe works in conjunction with the Receive Unit to verify phase identification along with the actual phase angle data. This is all done without any calculations or data transfer from the field to a base computer. The meter probe and reference probe or receive unit can operate at 100 feet of separation and up to 300 feet line of sight separation. In the event that this distance would need to be greater, the Receive Unit can be unplugged from the charging cable and taken into the field while operating on it's rechargeable batteries for up to 8 hours at a time.

  • DC Gaussmeter

    GM1-ST - Alpha Lab, Inc.

    The Model 1-ST measures strength and polarity of magnetic fields up to 19,999.9 gauss. The sensor can easily fit in a .060 inch (1.5 mm) gap and is at the end of a 100 cm flexible cable. The sensor end can be bent if required for a variety of situations. Place the sensor on a magnet face to measure the field. With a resolution of 0.1 gauss, it can measure any tiny variation from magnet to magnet or it can detect if a given magnet has lost even a little strength. Bend the sensor in to a "L" to measure inside a DC solenoid tube. The 5 digit display requires neither auto nor manual range change, making it easier to use than older style 3 or 4 digit meters. Turn on the meter and immediately begin reading fields (updates 4 times per second). There is no setup required, making this the fastest, easiest gaussmeter available.

Products

Applications

Manufacturers