Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 3766 - 3780 of 4429 products found

  • Power Calibrator and Protection Relay Test Set

    CP11B - Calmet Ltd.

    Single phase, class 0.02 and 0.05 power quality calibrator up to 120A and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays

  • VALVE & BOX LOCATOR

    7-T - Tinker & Rasor

    Rugged "Cycolac" instrument housing and detection headTelescoping HandleVisual Meter & Battery TesterBuilt-in speaker, signal and battery test meterOne sensitivity control knobBalanced and lightweight Adjustable extensionSet of stereo headphones3 Replaceable "AA" Alkaline batteriesDependable

  • Standard Sad and Dust Test Chamber

    ACE Technology Limited

    This product is applicable for the dust proof and resistant test of various auto components and parts including lamps, meters, electric dust proof sheath, steering sysytem and lock, etc.

  • Substation Maintenance and Commissioning Test Equipment

    T 3000 - ISA Srl

    This primary current injection testing system is designed to perform primary tests requested in substations commissioning. It allows to perform different tests and measurements on current transformers, voltage transformers, power transformers, protection relays, energy meters and transducers.

  • Video Inspection Scope

    BK3000 - Snap-on Inc.

    • Integrated 8.5 mm high-res imager allows for ease of use and ensures the product is always ready to go. Imager is resistant to dust, dirt, and water ingress for 30 minutes at depths of up to 3 meters.

  • Voltage & Continuity Tester

    ET250 - Klein Tools, Inc.

    The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.

  • Pulse - Generator

    PG 01-2000 - Schlöder GmbH

    The test generator PG 01-2000 is suitable for insulation test and testing of the impulse withstand voltage of electrical and electronic electricity meters. The generator produce a standard pulse voltage waveform with 0,1 / 2000 μs.

  • Signal Finder

    SATHERO Technology Co.,Ltd

    Digital satellite finder, Digital satellite meter, HD DVB-S/S2, Demodulation QPSK, 8PSK, Display POWER、C/N、Quality value, Upgrade software & parameters through USB2.0 Port, Easy to read LCD.

  • Soil Thermal Conductivity Portable

    TLS-100 - Thermtest Inc.

    The TLS 100 Meter is a portable tester for the measurement of thermal conductivity and thermal resistivity in accordance with ASTM D5334 - Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure.

  • DC Power Supplies & DC Power Packs

    Haefely Hipotronics

    HAEFELY HIPOTRONICS high power ranges of supplies are either air or oil insulated. There are numerous protection features provided in these power supplies including input and backup breakers, adjustable overload relay (10-110% of rated current), fast overload sensor, zero-start interlock plus provision for external safety interlock, current-limiting resistor in output circuit, output shorting solenoid (and/or stiff resistive bleeders) and fuse or circuit breaker protection of controls. Standard high power supplies are available from 1kW to 50kW and 1kV to 300kV and are furnished with shielded coaxial output cable. Rated current is available from zero to maximum voltage and all power supplies feature solid-state rectifiers, meter calibration, surge/transient protection of meters, relays and voltage regulators. Controls include a meter polarity-reversing switch in addition to input power and overload circuits.

  • Electric Energy Test Equipment

    Kvtester Electronics Technology Co.,Ltd

    Clamp Phase Meter is special designed for voltage, current and phase tests, it is in high-precision, low price, portable hand-held, dual-channel input measuring. It's easy to measure the phase between U-U, I-I and U-I, identify the inductive circuit ,capacitive circuit and the phase sequence of three-phase voltage, detect the wiring group of transformer, test the secondary circuit and bus differential protection system, display the phase relationship among the CT groups of a differential protection system, and check if the wire of electric meter was correctly connected. When testing customers do not need cut off the tested current which input by clamp-current transformer. When measuring the phase between U1 and U2, the two input circuit loop are completely isolated, so the possible misconnection is absolutely avoided, which may result in short circuit and may even burn the meter. The monitor of the device is high-contrast LCD screen, and the character in big size, which helps to obtain the best visual effects.

  • HSI Test Fixture

    TA-552 - Tech-Aid Products

    This test fixture provides the necessary panel controls, switching and cable pin-outs required to test the KPI-552/KPI-553/A series of HSI's as described in their respective maintenance manuals. This fixture will serve as the "Instrument Bench Tester" and does have the required differential resolvers and relay switching. Panel jacks are provided for the Heading, Course, RMI and ADF synchro sources that are external to this fixture. The use of external synchro sources serves to minimize the cost of this panel. Additional items incorporated on the panel are test jacks to monitor the meter drive voltage and current as well as a momentary switch to open the meter drive and this serves to verify sticky meter stops. The fixtures rear panel provides for all power inputs as well as an I/O connector if the shop desires to interface an external synchro panel.

  • Half Wave Rectifier

    HWR-1312B - Applied Precision Ltd.

    Half Wave Rectifier is designed for meter testing according to IEC 62053-21 Appendix A.1 - Half wave rectification (d. c. and even harmonics).The Half Wave Rectifier HWR 1x12B is a single phase (HWR 1112B) and three phase (HWR 1312B) device which acts as an ideal diode with null-voltage switch and negligible power loss. The device enables to test single or three-phase meters up to 120A. It requires division of tested meters into two equal sections. The sections are fed by the opposite half-wave. Due to null-voltage switch principle the symmetry of the load impedance is not critical for exact power split and therefore for the measurement accuracy. The Half Wave Rectifier acts as a linear device and does not affect the current source signal distortion.

  • Turnkey Solution for Unattended Noise Monitoring

    NoiseScout - NTi Audio AG

    NoiseScout provides a comprehensive but easy-to-use 24/7 noise monitoring solution. Noise levels are recorded on-site by the XL2 Sound Level Meter and are available online for monitoring and download. NoiseScout is aimed at both short term noise assessments and long term monitoring applications. During acquisition, automated email alerts allow noise issues to be addressed before a non-compliance condition arises. NoiseScout displays the noise levels measured by the XL2 Sound Level Meter live in your web browser. The measurement data recorded out in the field is presented online in charts and dashboards. Multiple noise level meters can be monitored simultaneously within the map view, thus providing localized geographic visualization for all noise levels at a glance. Identified users can access all their projects, control their monitors or create basic view modes, allowing stakeholders to oversee their noise level data.

  • Dual-Clamp Earth Resistance Tester

    HT25 Series - Wuhan Huatian Electric Power Automation Co., Ltd.

    With the rapid development of China's power industry, electrical equipment preventive experiment is an important part in protecting the safety operation of power system and maintenance. Insulation diagnosis is an important method to detect insulation defects or failure. Pointer insulation resistance tester is the special instrument to measure insulation resistance. JJG662-89 "insulation resistance meter (megger)" approved in May 1990 requires that insulation resistance meter is one of compulsory verification instruments. Nowadays the development trend of electrical equipment (such as transformers, generators, etc.) is that high capacity, high voltage, diversified structure and better seal. So insulation resistance meter (pointer) itself must have the characteristics such as large capacity, strong anti-interference ability, diversified measurement indexes, accurate measurement results, easy and fast measurement process, easy to carry and so on. The instrument produced by our company is equipped with ultra-thin taut suspension meter. It is an ideal tester to measure insulation resistance of these equipments such as transformer, instrument transformer, generator, HV motor, power capacitors, power cables, arrester, etc.

Products

Applications

Manufacturers