Filter Results By:

Products

Applications

Manufacturers

Meters

sense and display measures of gas, water, electricity, particles, vibration or light.


Showing results 4306 - 4320 of 4373 products found.

  • B2961/62A 6.5 Digit Low Noise Power Source

    Keysight Technologies

    The Keysight B2961A/B2962A 6.5 Digit Low Noise Power Source are a new generation of power supply/sources offering 6.5 digit best-in class-precision, wide bipolar output ranges of 100nV-210A & 10fA-10.5A, and an extremely low noise floor of 10 Vrms and 1nVrms/Hz (at 10 kHz). It also offers innovative features such as graphing capability and arbitrary waveform generation capability (10 mHz-10 kHz), which enable tests and evaluation that conventional power supply/sources cannot do. These features make the B2961A/B2962A ideal companion sources to use with other instruments such as oscilloscopes, network analyzers, spectrum analyzers, frequency counters, digital multi meters, nano-voltmeters, etc. The advanced features of the B2961A/B2962A provide researchers, electronic development engineers and electronic technicians with the tools that they need to meet their most difficult measurement challenges.

  • Battery Charger-Analyzer for small battery systems (up to 10A-Hr)

    24-400xg - JFM Engineering

    The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.

  • AUTOMATIC SAFETY TEST PANEL

    AUTOTEST - 001U - Premier Electrosystems

    Carries out open circuit /short circuit test,HV test, ECR test, Leakage current test and wattage test automatically & sequentially.Digital Indication of all the para meters with accuracy of class 1 or better.User adjustable set value parameters - on front panel controls.Auto/Manual operation.Test ON and test FAIL Indication by means opf individual LEDS.Facilities to bypass any test / tests.Test time continously adjustable between 1 to 10 sec.Facility to abort the test cycle after any test / tests failures.Modular construction for easy serviceability.Easy to operate even by unskilled person.Supplied with an attractive, transperant, rugged acrylic box with built in limit switch to house the appliance under test.An ideal Automatic instrument to carry out Pre Dispatch Safety Tests of industrial / domestic appliances.Designed with relevant ISI drafted specifications.Calibration certificate traceableto international standards meeting ISO9000/ISI requirements.

  • Cable/Circuit/Lighting Arrester Test Device

    Wuhan NANR Electric Co,. Ltd

    cable fault detector is to cater to industrial-grade power industry solutions and IT era of rapid development, the original cable fault tester limitations, using industrial embedded computer platform systems, network services, USB communication technology systematic, very greatly improve the instrument''s functions and use value and convenient on-site environmental operations. Especially for the growing number of buried cable provides a unique data management software. The entire system meets PRC power industry standard "DL/T849.1 ~ DL/T849.3-2004" special test equipment electrical equipment General technical conditions, the system is tested by the system host and the fault locator and meter three-part cable path for all kinds of power cable fault test, cable path, the depth of buried cables and cable testing archives to find the daily maintenance and management, as well as railways, airports and signal control cables, and streetlights accurate cable fault testing

  • PC Controlled Bench Top Power Analyzer

    PA2100 - Powertek LLC

    The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.

  • 6000 Series Digital I/O Modules

    Pacific Instruments, Inc.

    Series 6000 digital I/O modules record signals from frequency counters, flow meters, encoders, discrete transducers, IRIG time, etc. which are often part of the test environment. These digital signals are time aligned and recorded alongside the system’s analog measurements. High density digital inputs provide an opportunity to easily include facility controls like switches, valve positions, relays, lights, etc. along with the test data. Series 6000 digital I/O modules also provide outputs generated by user command or automatically by Sequence, Alarms or DSP. User generated outputs are accomplished in software while sequencers can be programmed prior to a test and initiated by program or hardware control. Alarm conditions preprogrammed on the analog side can automatically generate digital outputs which are typically connected to facility control systems or PLCs. A DSP adds powerful real-time processing and is appropriate for PID control loops, derived parameter calculations and a variety of other real-time operations.

  • 10 MHz to 18 GHz USB Wide Dynamic Range Average Power Sensor

    U2043XA - Keysight Technologies

    Accurately measure any modulated signal with the Keysight Technologies, Inc. U2040 X-Series wide dynamic range power sensors. The USB connectivity models come with world's widest dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U2040 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.

  • 10 MHz to 6 GHz USB Peak and Average Power Sensor

    U2042XA - Keysight Technologies

    Accurately measure any modulated signal with the Keysight Technologies, Inc. U2040 X-Series wide dynamic range power sensors. The USB connectivity models come with world's widest dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U2040 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform complex pulse analysis and standard average power measurement.

  • 10 MHz to 6 GHz USB Wide Dynamic Range Average Power Sensor

    U2041XA - Keysight Technologies

    Accurately measure any modulated signal with the Keysight Technologies, Inc. U2040 X-Series wide dynamic range power sensors. The USB connectivity models come with world's widest dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U2040 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.

  • 16-Bit, 250 kS/s, 16 AI, 2 AO, 24 DIOSinking, Voltage Input/Output Bank Isolation

    PXI-6233 / 779620-01 - National Instruments

    16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6233 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6233 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.

  • Analog Tank Test Kit

    4108 - M. C. Miller Company

    The voltmeter included in the kit, the “Model IA” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers a 0 - 2VDC range with a 10MΩ input impedance and the analog display presents a color divided scale for convenient indication as to whether or not a carbon-steel structure is receiving a suitable level of cathodic protection, with respect to the accepted 0.85V (850mV) threshold value.

  • Polarization Controller

    8169A - Keysight Technologies

    The 8169A Polarization Controller, with single-mode fiber input and output, is used to change light from any polarized or unpolarized light source into any well-defined state of polarization. The design based on bulk-optic zero-order waveplates and a high-performance linear polarizer at the input provides optimum determination and repeatability of polarization states over a wide wavelength range. The 8169A is especially well suited for use together with a tunable laser to make swept-wavelength measurements of the polarization dependence of fiberoptic devices, by setting a set of relatively orthogonal polarization states for Mueller Matrix analysis. These measurements are supported by a Plug&Play driver and coordinated operation of the 8169A with a Keysight tunable laser and power meters can be enhanced with the Photonic Foundations Library software package. The fundamental basis of this flexible instrument also supports many general applications requiring polarization control and analysis.

  • Oscilloscope

    CLEN096 - Nanjing Clean Energy Electronic Technology Co.,Ltd

    CLEN096 has similar structure as CLEN062 but its performance has been significantly improved. Comparing to 062 CLEN 096 bandwidth is 5 times wider (5M vs 1M) and sensitivity is 10 times higher (10mV vs 0.1V). Particularly, its frequency meter has been greatly enhanced. It can measure frequency higher than 20MHz at sensitivity better than 0.2Vpp (062 can only take 5 - 6 MHz signal and requires TTL level). Another big improvement is that CLEN096 is battery-powered. Accepted voltage ranges from 2V to 5V so one regular 3.7V Li-ion or two 1.2V Ni-HM batteries can be used. It also comes with a built-in charger specific for 3.7V li-ion battery. CLEN096 has built-in USB-Uart converter which easy-off firmware upgrade and waveform upload. It can also run on USB power without battery.

  • OTDR

    AQ1000 - Yokogawa Meters & Instruments Corporation

    Yokogawa Meters & Instruments Corporation will add an entry-level model, the AQ1000, to its range of OTDR (Optical Time-Domain Reflectometer) test instruments. The new model will be launched for sale outside Japan on April 13th. The new instrument complements the company’s mid-range AQ1200 Series and the high-end AQ7280 Series, and is specifically designed to increase the productivity of field personnel working on the installation and deployment of optical access networks such as Fiber To The Home (FTTH): the so-called “last mile” to consumers’ premises. The worldwide use of these optical access networks is increasing dramatically as the FTTH network structure is more and more adopted by the telecom operators, and optical fibers replace the copper cables in each household. Consequently, more and more installers will be working on fiber-optic deployment over the last mile. These installers will not need high-end OTDRs capable of measuring over hundreds of kilometers in the core network. Instead, they will need affordable OTDRs equipped with all the features which can make their job easier and faster: instruments like the Yokogawa AQ1000.

  • OTDRs and Fault Locators

    AFL

    AFL optical time domain reflectometers (OTDRs) and fault locators are used to certify new fiber installations and locate faults in deployed fiber optic networks. OTDRs and fault locators are available for both multimode and single-mode networks, including FTTx PONs. OTDRs scan fiber optic networks from one end of the fiber, displaying a trace and reporting detected events such as splices, connectors, micro- or macro-bends and fiber end. Fiber length is reported along with location, loss and reflectance of detected events. Several OTDRs are available with an integrated visual fault locator (VFL), optical light source (OLS), and/or optical power meter (OPM). OTDR results can be saved and uploaded to PC for further analysis and/or archiving.