Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 4336 - 4350 of 4395 products found

  • P4455 Power Monitoring For Dummies - Power Monitor

    Company: P3 International

    Now anyone can cut electricity costs and find out what appliances are worth keeping plugged in. Simply connect an appliance to the meter, and it tells you the monthly cost. The unit measures consumption by the kilowatt hour — the same way as your local utility company.By using this device, you can figure out how efficient each appliance actually is. Now you can decide if it's finally time to get that shiny new refrigerator you've been eyeing or if your old air conditioner is the power hog you thought it was.You can calculate your cumulative electrical expenses and forecast usage by the day, week, month, or even an entire year. Also check the quality of your power by monitoring the voltage. With Power Monitoring For Dummies, you can now know "watts" killing you.

  • Reflectometers

    Company: Luna Technologies

    High resolution OFDR – Resolve individual features with spatial resolution down to 10 microns.High sensitivity – 70 dB of dynamic range and -130 dB sensitivity.Long range – Measure up to 2000 meters in length with a single connection, single scan.Single Connection IL and RL – Measure insertion and return loss in a single scan.Locate loss events – Monitor backscatter levels to isolate losses due to bends, crimps, bad splices, etc.“Look inside” devices – High resolution and sensitivity enable inspection of individual components within a subsystem.Polarization Tracking – Track changes in the state-of-polarization as light propagates through an optical network.Intuitive graphical interface – All key data and graphs in a simple, easy to use interface.Distributed sensing – Use standard optical fiber to monitor the changes in temperature and strain

  • SY017 - Recipe Batch Controller

    Company: Synectic Electronics

    This Multi recipe batching system offers a stand alone complete weighing, monitoring and process control solution, with non-volatile memory storing up to 100 recipes. The SY017 can be fully integrated into a factory network or with a PC give unlimited recipe storage and control. Weight measurement is achieved with an 18bit ADC, and the built-in excitation supply will drive up to four 350Ω load cells. An optional flow meter input is also available. The unit controls the switching of up to 17 valves, motors, pumps or contactors etc. using relays rated at 5A 250V AC or 5A at 30V DC. A 4-20mA output is available as an option for remote indicators or a variety process control applications. speed control of mixers conveyors etc.

  • MFF-1 - RF Multifrequency Filter

    Company: ROM-Elektronik GmbH

    Since 2003 on the market and more current than ever! For us, it was already clear at this time what importance the service-specific analysis of high-frequency signals has and will have. We are very pleased that this vision has also found its way into the current SBM2008 (standard of construction-based measurement technology). The MultiFrequency filter MFF-1 enables precise measurement of common services - simply by means of a selector switch, without a large investment in a spectrum analyzer and without complicated settings on the device. The filter is simply connected between the measuring antenna and the HF meter - ready. The MFF-1 only allows the frequencies that are selected! There are six switch positions available: base stations D-network and E-network, DECT, base station UMTS, WLAN / Bluetooth, microwave oven and broadband (all frequencies).

  • CNG-EbNo - SNR Noise Generator

    Company: Noisecom

    The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signals are used to compare theoretical BER to SNR ratios, found in "waterfall" type graphs, with measured values from the DUT to evaluate different modulation schemes. Users can obtain higher yield through automated testing, plus increased confidence from repeatable, accurate test results. Standard units can be modified for specific customer requirements. Please consult the factory for pricing and availability of these requests.

  • SuperMasterCharger - Intelligent Battery Charger-Analyzer for Large Battery Systems

    Company: JFM Engineering

    The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.

  • SuperMini - Intelligent Battery Charger-Analyzer for Battery Systems

    Company: JFM Engineering

    The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.

  • BD Series - Load Banks

    Company: Manatronics Pty Ltd

    Quality ProductRugged and Reliable DesignVery Cost effectiveMicroprocessor controlled200 Amps at 60V (continuous rating)12kW RatedPortable – very light weight LoadSmall case size with carrying handlesContinuously variable currentConstant Current operation is standardOptions for CP, CR, CV modes.Completely powered from batteries.Two LCD digital panel meters for Voltage and CurrentThermally safeFan fail detect on all fans / Air flow blockage detectorsFused protection optionOvervolt protectionIntelligent Load feature; has built-in LVD to remove load at “End Voltage”Selectable “End Voltage” prevents deep discharge and possible damageAmplified Shunt output is availableRemote enable / disable (suitable for UPS control)An Anderson SB 350A series connector for DC power connection

  • LCR-Reader Probe Shielded Two-Wire Connector

    Company: Siborg Systems

    Siborg''s LCR-Reader Probe Shielded Two-Wire Connector allows to use LCR-Reader as a probe station. It also allows users to measure components that are beyond the tweezers allowable spread. The Connector is fully compatible with other tweezer-like meters in particular all models of Smart Tweezers. The kit comes with 7 different kinds of probes; 2 alligator clips, 1 longer pin-probe, 1 medium pin-probe, 2 multimeter 4 mm jack plugs, 1 spade connector. Each tip screws into the end of the connector cable. The LCR-Reader Probe Connector is simple to install: simply unscrew one of the gold-plated probes from LCR-Reader; place the flat side of the connector cable on the LCR-Reader''s probe arms with the gold flex cable and the connector cable''s flat end with two gold stripes. Return screws to the holes and start measuring.

  • CTS-M5 Series - Microprocessor Based Transmitter

    Company: Automation Components

    The CTS-M5 Series has a microprocessor based transmitter. It uses an Electrochemical gas sensor to monitor a variety of gases. The CTS-M5 Series offers great value since it includes many standard features that can only be found as expensive options in other manufacturer's models. A digital display (LCD), push-button programming and on-board meter jacks are all standard. The transmitter provides an analog output of 4-20 mA DC or 2-10 VDC, proportional to the measured gas range, for transmission to the Building Automation System. The CTS-M5 Series offers flexibility and simplicity in one package. The relay setpoints may be seen as increasing or decreasing actuation simply by adjusting the deadband relationship. Set the deactuation point above the actuation setpoint and the CTS-M5 will automatically alarm on decreasing concentrations. Plus, calibration is extremely simple. First, apply the calibration gas and then adjust the potentiometer to the desired reading on the display.

  • mTFX-C1 - MAP-200 Multiport Tunable Filter Module

    Company: Viavi Solutions

    The mTFX-C1 is a modular Ethernet or GPIB instrument and can be directly managed from your PC-based automation system. It eliminates the need to re-purpose optical network technology or use complex libraries with specialized interface cards. Based on next-generation liquid crystal on silicon (LCOS) technology, the mTFX-C1 is much more than a tunable filter. It combines variable attenuator, switch, power meter, and DWDM multiplexer functions to dramatically simplify photonic testing of coherent interfaces, amplifier, and DWDM systems. Leveraging TrueFlex™ technology, filters are continuously tunable in center wavelength and bandwidth and are not locked to the ITU grid. Multiple parallel wavelength paths can be created without disrupting already established connections—all with sub-GHz resolution. Industry-leading specifications for loss and out-of-band rejection ensure minimal impairments on your test signals.

  • Function Generators

    Company: Shanghai MCP

    Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad

  • AL-57FL - Fused Test Probes with Silicone Test Leads

    Company: Standard Electric

    AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-quality silicone test leads, 1.5 meter long.● Wipe the fused test probes and silicone test leads periodically with a damp cloth and detergent. Do not use abrasives or solvents.● Operating temperature: -20 °C to +50 °C (-5 °F to 120 °F)● One year warranty● Can't be used on current mode with blown fuse.● Rating : EN 61010-031 CAT Ⅲ 1kV 10A / CAT Ⅳ 600V 10A

  • NanoSpec 6500 - Film Thickness

    Company: Toho Technology

    The NanoSpec 6500 utilizes an advanced spectroscopic reflectometer to measure optically transparent films that are used in the manufacture of thin film on glass for displays and other applications. Designed for maximum throughput, reliability and accuracy, the NanoSpec measures all transparent or translucent multi-stack films on virtually any kind of substrate. Capable of handling all sizes from “tablet” size glass to G10 panels almost three (3) meters square, the 6500 is specifically designed for a wide variety of production applications. The rugged system provides precise measurements of single-layer films such as oxide, nitride and photo-resist, as well as the top layer on film stacks of up to 3 layers in the thickness range of 100Å to 35µm and features an optional 0.75µm spot for small areas. Proprietary software enables Multilayer Film Analysis with the ability to select film constants, scan ranges and substrate types, the 6500 is the ideal tool for rapid process control measurements at the production level.

  • PA2100 - PC Controlled Bench Top Power Analyzer

    Company: Powertek

    The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.

Products

Applications

Manufacturers