Filter Results By:

Products

Applications

Manufacturers

Meters

sense and display measures of gas, water, electricity, particles, vibration or light.


Showing results 4411 - 4425 of 4429 products found.

  • Zero Gauss Chamber

    ZGC - Alpha Lab, Inc.

    The model ZGC zero gauss chamber reduces the environmental magnetic field (Earth field) to near zero inside the chamber. Any gaussmeter probe which is less than 9.4 mm or 0.370" diameter can be placed inside. The meter is then "zeroed", which means that it will read zero whenever the probe is subsequently placed in zero field. By using a zero gauss chamber, any offset error is therefore eliminated. The model ZGC is unique in that it contains a degausser (demagnetizer). This is situated between the inner and outer mu-metal shields. When the degauss button is pressed, any accidental magnetization of the chamber, no matter how strong, is erased. Accidental magnetization is a major problem with most zero gauss chambers and it has limited their use. If a magnet comes too close, the chamber will become "permanently" magnetized and will have an internal field that is typically 0.2 to 0.5 gauss. The chamber must then be degaussed because the Earth field is also around 0.5 gauss, so a magnetized zero gauss chamber will not significantly reduce the field.

  • PXI Strain Gauge Simulator Module 4-Channel, 2k

    40-265-304 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 1k

    40-265-204 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 3k

    40-265-102 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 1.5K

    40-265-402 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 3k

    40-265-106 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 350

    40-265-016 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 1.5k

    40-265-404 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 2K

    40-265-302 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 1k

    40-265-206 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 2k

    40-265-306 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 1.5k

    40-265-406 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 3k

    40-265-104 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 350 Ohm

    40-265-012 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • RF Power Amplifier Automatic Measurement System

    Acery Technologies

    RF power amplifier automatic measurement system consists of a new generation of science and technology is the German spectrum analyzer, RF and microwave signal source, network analyzers, noise figure analyzers, power meters, digital oscilloscopes, high performance DC power supplies, multimeter, low-frequency switching and digital I / O, custom RF and microwave switch matrix and other equipment and related equipment. These high-performance equipment not only provides incentives and analysis for the amplifier under test, but also provides a DC power supply and power amplifier circuit and other peripheral adjustment necessary. Meanwhile, the system sets the test signal conditioning, configuration and calibration test as one of the major parameters which can be accurately amplifier, fast and flexible testing. All equipment is controlled by the core of the test system software can be fully automated production test and manual type of R & D design type tested to meet the testing requirements of different stages. System software includes a convenient test mode conversion, simple and clear path and test switch interface, the main instrument soft front panel measuring device, and a measurement report in line with MS Word and Excel format and other functions.