Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 4456 - 4470 of 4475 products found

  • RF Power Amplifier Automatic Measurement System

    Acery Technologies

    RF power amplifier automatic measurement system consists of a new generation of science and technology is the German spectrum analyzer, RF and microwave signal source, network analyzers, noise figure analyzers, power meters, digital oscilloscopes, high performance DC power supplies, multimeter, low-frequency switching and digital I / O, custom RF and microwave switch matrix and other equipment and related equipment. These high-performance equipment not only provides incentives and analysis for the amplifier under test, but also provides a DC power supply and power amplifier circuit and other peripheral adjustment necessary. Meanwhile, the system sets the test signal conditioning, configuration and calibration test as one of the major parameters which can be accurately amplifier, fast and flexible testing. All equipment is controlled by the core of the test system software can be fully automated production test and manual type of R & D design type tested to meet the testing requirements of different stages. System software includes a convenient test mode conversion, simple and clear path and test switch interface, the main instrument soft front panel measuring device, and a measurement report in line with MS Word and Excel format and other functions.

  • SDI video inserter

    6041G-HD - Instrumentation Technology Systems

    The Model 6041G-HD is a ruggedized SDI video inserter. When the unit is placed within 100 meters of an SDI video source, the 6041G-HD enables accurate time stamping of each video frame/field. Time stamping prior to any compression and transmission of the SDI stream from a remote source such as a range camera, ensures that time recorded is accurate to within 10 microseconds of the frame or field sync.. Since the unit reclocks the SDI stream, it may also be used as a repeater extending the distance from the SDI video source to the transport insertion equipment (compressor, Ethernet, or other transport means). The unit auto-detects and decodes the imaging format permitting most SDI 480i/p, 720p or 1080i/p NTSC or PAL sources to be connected without having to change system settings. The time message may be inserted into the active video image, with the color (1 of 16) and location selected by the user. When selected, the time is also inserted into the SDI meta-data (vertical ancillary packets) in accordance with MISB STD 0605.3 and NATO STANAG 4609. The time reference is derived from either the internal GPS receiver or an external IRIG B time code source. If the GPS or IRIG lock is lost the unit will automatically continue to run on an internal clock.

  • Seismic Sensor

    D7S - Omron Electronic Components

    Specifically designed for the growing number of autonomous IoT systems, the Omron D7S provides high precision measurement of spectral intensity, allowing it to reject impulse vibration noise and only respond to genuine seismic activity. Despite its compact size, D7S features its own internal memory and I2C interface, allowing it to be readily integrated into IoT devices. Potential applications include smart electricity and gas meters, wireless sensors, industrial control panels, electricity distribution panels, fire-prevention systems, home appliances such as heaters and gas stoves, chemical plants, expressways, bridges, tunnels, roads and many more. Commenting, Fabrizio Petris, Senior Business Development Manager of Omron Electronic Components Europe said, “Earthquakes are extremely common around the world. On average, 50 earthquakes strike each day, or about 20,000 a year. Many are weak enough to go unnoticed but some are catastrophic. We can’t always predict when a catastrophe will strike. Using the new sensor from Omron, designers can make systems safer and minimise the risk of secondary damage after earthquakes by safely shutting off and stopping hazardous devices. The sensor can also help determine damage by mapping seismic intensity and providing building collapse information.”

  • Proactive Downstream Spectrum Analysis

    SpectraVizion - ZCorum

    SpectraVizion is an innovative, software-based diagnostics tool that leverages new advancements in remote spectrum capture, allowing cable operators to address downstream spectrum impairments proactively, before subscribers call in with service complaints. “Troubleshooting downstream spectrum issues has always been a reactive process for cable operators,” said Arthur Skinner, Vice President of Worldwide Sales for ZCorum. “Often they’re not aware they have an issue until a customer calls, and that’s when they then send a technician to the home with a hand-held meter to start a search for the problem.” SpectraVizion takes the guesswork out of problem identification and location by presenting on a simple dashboard a list of devices that are experiencing common downstream issues like Standing Waves, FM Noise, Suck-outs, Roll-off and Tilt. The tool leverages the spectrum data available from cable modems and set-top boxes that support full band capture, and advanced detection algorithms automatically identify devices experiencing downstream impairments. The operator can click on any device in the list to view a capture of the full spectrum from that day, or up to 30 days in the past.

  • Solar Simulator

    Unisim Compact Solar Simulator - TS Space Systems

    The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.

  • PXI Strain Gauge Simulator Module 4-Channel, 2k

    40-265-304 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 1k

    40-265-204 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 3k

    40-265-102 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 1.5K

    40-265-402 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 3k

    40-265-106 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 350

    40-265-016 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 1.5k

    40-265-404 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 2K

    40-265-302 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 1k

    40-265-206 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 2k

    40-265-306 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

Products

Applications

Manufacturers