Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 4606 - 4620 of 4675 products found

  • MM10 - Digital Multimeter Full Function DC and AC Voltage

    Company: Dwyer Instruments

    Our compact, low cost Model MM10 Digital Multimeter is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC and AC voltage to 600V, DC current to 10A and resistance to 20 MO. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. Rotary switch allows you to select from any of the twenty ranges quickly and easily. The 3.5 digit LCD features automatic polarity correction, low battery and overload indication. Rugged, high impact case comes equipped with built-in tilt-stand for versatile, hands-free operation. Overload protected to 600 VAC/600 VDC for voltage ranges and to 500 VAC/500 VDC for resistance, diode and continuity test ranges. Current ranges are protected by 0.5A/250V, replaceable fuse. Multimeter is furnished with 22" test leads, 9V battery and instruction manual.

  • TruVizion - Broadband Diagnostics

    Company: ZCorum

    TruVizion gives you a comprehensive view into the health of your cable or DSL network, including up to 90 days of historical data.PreEqualization Analyzer lets you quickly find upstream impairments like reverse splitters, loose or corroded connectors and bad wiring. Plus, you can be proactive and actually fix those problems before they affect service for your subscribers.RF Inspector is an inexpensive app that can do what a meter can do, except it can do it on a tablet from wherever you happen to have Internet access. That means in the office, at home, or in the field.Upstream Analyzer shows you the RF signals for all ports and modems on your Cisco CMTS without any additional equipment, cabling or connectors, and yes, you can see ingress under the carrier with one click.

  • Color Analyzers

    Company: PCE Instruments

    Our professional colour analysers include the RGB series. With these colour analysers you can read the difference in colour in L d*a*b*, L*C*H* and Delta E*ab according to your requirements.Colour Analyzers for both colour and luminance for measuring surface colours of products.The most popular model of colour meter in our range of products is the PCE-RGB. Aside from being easy to use and economical, our colour analysers are used for determining the location of a colour on the XYZ axis of non-radioactive products. The geometry of the measurement of these colours, with luminosity including a field of measurement of 8mm allow for universal use for all types of materials. The range of applications of colour analysers is extensive and includes industry, agriculture, crafts, commerce, as well as research and development

  • VA8042 - Coating Thickness Guage

    Company: Shanghai Yi Hua V&A

    By electromagnetic method, the meter can measure the coating thickness non-destructively, including paint, spray-plastic, rubber, enamel, or chrome plate, copperizing, aluminium plating on steel, iron, non-austenitic stainless steel. Four digitals LCD display, differentiating upto μm. System calibrating by user-self.Pocket shell, convenient for engineering locale .Thickness unit “μm” or “mil ” optional.Micro-controller controls, high accuracy .Coupling state display.Shut down manually or automatically.Low battery voltage indication.SpecificationsDigital display:4 digitals.Measurement range:0~1200μm.Resolution: 1μm .Accuracy: ±(3%H+2μm).Measurement rate:0.5 second.Display units:μm or mil.Critical thickness of metallic base:1mm.Minimum thickness of metallic base:0.2mm.Minimum curvature radius:protruding 1.5mm, concave 6mm.Probe diameter:13mm.Power supply: AAA 1.5V*3 .

  • KI-TK072A - Complete SM & MM Contractor Certification FiberTester Kit

    Company: Kingfisher International

    Kingfisher International is pleased to announce immediate availability of 5 Wavelength Optical Clean / Inspect / Test Kits, which are the perfect solution for contractors looking to work on multimode and single mode fiber optic systems including an additional test wavelength such as 1625 nm. The KI-TK072A - SM & MM Contractor Kit includes cleaning materials, a high quality x200 microscope, power meter and a 850 / 1300 nm LED & 1310 / 1550 / 1625 nm Laser Light Source, all fitted with interchangeable connectors, and powerful reporting software. The compact molded semi-rigid carry case is comfortable to use, provides good equipment protection, and also allows users to immediately identify if anything has been accidentally left out. It has additional space for an optional VFL and various test accessories.

  • DigiMano BP - Calibration Kit

    Company: Netech

    The DigiMano BP Calibration Kit combines our most popular pressure meter, the DigiMano 200-2000IN, with our patented Syringe Pump, making it an ideal calibrating tool for most blood pressure instruments including Welch Allyn, and Sphymanometer pressure dial gauges. This unique Syringe Pump allows the technician to apply a steady and set pressure to both the Spygmanometer and the Digimano 1000 for easy comparison. A high quality pressure calibration kit, it saves technicians and nurses time when checking and validating the accuracy of the Blood Pressure Machines. It comes complete with Luer-Lok connectors and tubing. Compact and easy to use, the DigiMano BP Kit is designed exclusively for blood pressure gauge calibration checks recommended by most pressure gauge manufacturers.

  • Cable/Circuit/Lighting Arrester Test Device

    Company: Wuhan NANR Electric

    cable fault detector is to cater to industrial-grade power industry solutions and IT era of rapid development, the original cable fault tester limitations, using industrial embedded computer platform systems, network services, USB communication technology systematic, very greatly improve the instrument''s functions and use value and convenient on-site environmental operations. Especially for the growing number of buried cable provides a unique data management software. The entire system meets PRC power industry standard "DL/T849.1 ~ DL/T849.3-2004" special test equipment electrical equipment General technical conditions, the system is tested by the system host and the fault locator and meter three-part cable path for all kinds of power cable fault test, cable path, the depth of buried cables and cable testing archives to find the daily maintenance and management, as well as railways, airports and signal control cables, and streetlights accurate cable fault testing

  • NCVT-3 - Non-Contact Voltage Tester

    Company: Klein Tools

    Provides non-contact detection of AC voltage.Detects 12 – 1000V AC with simultaneous visual and audible voltage indicators.Bright flashlight illuminates work area and may be used independent of voltage detection function.Visual LED bar graph indicates the presence of voltage – the higher the voltage sensed, or the closer to the voltage source, the more LEDs light up.Bar graph visual voltage indicator utilizes up to five vibrant LEDs for easy interpretation/viewing.Audible voltage indicator beeps at a greater frequency the higher the voltage that is sensed, or the closer to the voltage source.“Auto Power-Off” conserves and extends battery life.Screw-thread battery cap with O-ring ensures protection against dust and water ingress.Lightweight, compact tool with pocket clip provides convenient storage and quick access.IP67: Dustproof and waterproof.6.6 feet / 2 meter drop protection.CAT IV safety rating for 1000V.Conforms to CE requirements.

  • SVM2 - Surface DC Voltmeter

    Company: Alpha Lab

    The SVM2 has high sensitivity (resolution), and can detect even a 1 volt charge anywhere within its full range of +29,999 to -29,999 volts. Thus it is easy to measure whether a given process is increasing or decreasing the static electricity present, even if the increase or decrease is by a tiny fraction. The meter reads the actual static signal, but it also captures and stores the highest positive and highest negative signals that were experienced since the last time that the "Reset" button was pressed. These peak + and can be displayed at any later time. The peak function has a "window" time of 0.005 seconds (which is much faster than the display) so even very quick peaks are captured and stored. There is also a user-settable alarm. The alarm will sound if the signal (whether + or -) ever exceeds the value set by the user for at least 0.005 seconds. The alarm can be reset or muted at any time.

  • Stages

    Company: Aerotech

    Aerotech manufactures a large selection of linear, rotary, and lift and Z-axis positioning stages that utilize our own brushless linear direct-drive servomotors, as well as ball-screw models driven with Aerotech brush or brushless rotary motors. Travels for our linear tables range from 25 mm to 1.5 meters. Aerotech''s positioning stages are utilized in high-performance applications in industrial robots, fiberoptics and photonics, vision systems, machine tools, assembly, semiconductor equipment, medical component laser machining, micromachining, electronic manufacturing, and other industrial automation applications. We even offer a complete line of nanopositioning stages that provide nanometer resolution, accuracy, repeatability, and in-position stability with travels from 25 mm to 160 mm. In addition, Aerotech manufactures drives and motion controllers that perfectly complement our positioning stages.

  • BB705 - Tempurature Reference Source

    Company: Omega Engineering

    This BB705 is a blackbody temperature reference source which is adjustable over the range from 100 to 1046°C (212 to 1915°F) and accurate to ±1°C, ±0.25% rdg. It has a built-in digital temperature controller to provide accurate, stable temperatures as well as to provide the temperature readings of the cavity. The heated cavity provides a target of known temperature and emissivity, and virtually any infrared pyrometer with a spot size diameter less than 44.5 mm (0.88") can be calibrated. Calibration setups are easy with the BB705. An independent NIST traceable probe and high accuracy panel meter provide temperature reference information. Both models come standard with an RS-232 computer interface which allows computer control of the setpoints for automatic test applications. A NIST traceable calibration certificate is also provided.

  • ETS-200T / ETS-200T-FT - Test System

    Company: Teradyne

    The ETS-200T / ETS-200T-FT discrete test platform is built on proven ETS technology and provides true index-parallel testing specifically for turret and rotary handlers. These test systems maximize throughput with pattern-based test techniques based on Eagle SmartPin™ technology coupled with the use of dynamic Cbits for enhanced user control. Both the ETS-200T and the ETS-200T/FT provides a complete test solution from wafer sort to final test for MOSFETs, including integrated control and datalogging for UIL, dVSD, Qg and LCR meter. Raptor™ software reduces program generation by providing a graphical user interface that does not require any programming experience combined with a robust set of test libraries and proven test techniques to increase test volumes and reduce cost of test.

  • BLU-FUZE Mortar Series - Telemetry Systems

    Company: Syntronics

    The BLU-Fuze Series In-Flight Telemetry Systems provide an extensive selection of shock hardened sensors to measure in-bore and in-flight performance of mortars and projectiles. All BLU-Fuze configurations include an integrated S-Band telemetry transmitter and antenna which relays the measured data to a ground station. The typical range of the telemetry exceeds 20,000 meters. The BLU-Fuze is conveniently packaged in the NATO standard fuze envelope for either artillery or mortar rounds so that it can add flight instrumentation and telemetry to a wide variety of munitions without any modifications to the munitions themselves. The BLU-Fuze is simple to use. The BLU-Fuze is activated when the battery pack is attached to the fuze body. The BLU-Fuze is then screwed into the fuze well of the mortar to be tested. Once activated, the BLU-Fuze will run for more than 45 minutes, providing ample time to verify the telemetry link, acquire GPS, load, and launch the projectile. Data is stored and transmitted after the round clears the bore beginning 100 msec before detection of the launch event.

  • BLU-FUZE Artillery Series - Telemetry Systems

    Company: Syntronics

    The BLU-Fuze Series In-Flight Telemetry Systems provide an extensive selection of shock hardened sensors to measure in-bore and in-flight performance of mortars and projectiles. All BLU-Fuze configurations include an integrated S-Band telemetry transmitter and antenna which relays the measured data to a ground station. The typical range of the telemetry exceeds 20,000 meters. The BLU-Fuze is conveniently packaged in the NATO standard fuze envelope for either artillery or mortar rounds so that it can add flight instrumentation and telemetry to a wide variety of munitions without any modifications to the munitions themselves. The BLU-Fuze is simple to use. The BLU-Fuze is activated when the battery pack is attached to the fuze body. The BLU-Fuze is then screwed into the fuze well of the projectile to be tested. Once activated, the BLU-Fuze will run for more than 45 minutes, providing ample time to verify the telemetry link, acquire GPS, load, and launch the projectile. Data is stored and transmitted after the round clears the bore beginning 100 msec before detection of the launch event.

  • 3312 - Telecom Transformer Test System

    Company: Chroma ATE

    The 3312 provides 20Hz-1MHz test frequencies. In addition to transformer scanning test function, the 3312 has LCR Meter function. In test items, The 3312 covers most of telecom transformer's low-voltage test parameters which include telecom test parameters as Return Loss (RLOS), Reflected Impedance (Zr), Insertion Loss (ILOS), Frequency response (FR), and Longitudinal Balance (LBAL) etc.; primary test parameters of general transformer as Inductance, Leakage I nduc t anc e, Turns -R a t io, DC re s i s t anc e, Impedance, and Capacitance (between windings) etc.; secondary test parameters of general transformer as Quality Factor and ESR etc.; and pin-shor t test function. High-speed digital sampling measurement technology combined with scanning test fixture (A132501) design, improve low-efficiency telecom transformer inspection to be more accurate and faster.

Products

Applications

Manufacturers