Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 5266 - 5280 of 5307 products found

  • ZC-203B - Transformer Ratio Tester

    Company: Kvtester Electronics

    Product Features1. Auto test the wire groups.2. Auto change the groups.3. Auto switch the phase sequence.4. Auto change the measurement range.5. Self calibrate the meters.6. Can auto calculate the relative error after input the standard ratio.7. Auto cut off the measured voltage after the test finished.8. Set the data, auto save the test results, can review the historical data.9. Only can enter one ratio value when testing the loading transformer. Technical ParameterEnvironment condition: Temperature: -5 °C~50 °CRelative humidity<95%(25°C)Altitude<2500mmExternal interference: no special strong vibration, no special strong electromagnetic fieldPower supply160VAC-280VAC,45Hz~55HzOutput range20V : Voltage0~20V Current 0~10V50V : Voltage0~ 50V Current0~5AThe ratio test range1~4000 Group test range0~11Angle measurement range0°~ 360° or - 180°~ 180°

  • BLU-FUZE Mortar Series - Telemetry Systems

    Company: Syntronics

    The BLU-Fuze Series In-Flight Telemetry Systems provide an extensive selection of shock hardened sensors to measure in-bore and in-flight performance of mortars and projectiles. All BLU-Fuze configurations include an integrated S-Band telemetry transmitter and antenna which relays the measured data to a ground station. The typical range of the telemetry exceeds 20,000 meters. The BLU-Fuze is conveniently packaged in the NATO standard fuze envelope for either artillery or mortar rounds so that it can add flight instrumentation and telemetry to a wide variety of munitions without any modifications to the munitions themselves. The BLU-Fuze is simple to use. The BLU-Fuze is activated when the battery pack is attached to the fuze body. The BLU-Fuze is then screwed into the fuze well of the mortar to be tested. Once activated, the BLU-Fuze will run for more than 45 minutes, providing ample time to verify the telemetry link, acquire GPS, load, and launch the projectile. Data is stored and transmitted after the round clears the bore beginning 100 msec before detection of the launch event.

  • BLU-FUZE Artillery Series - Telemetry Systems

    Company: Syntronics

    The BLU-Fuze Series In-Flight Telemetry Systems provide an extensive selection of shock hardened sensors to measure in-bore and in-flight performance of mortars and projectiles. All BLU-Fuze configurations include an integrated S-Band telemetry transmitter and antenna which relays the measured data to a ground station. The typical range of the telemetry exceeds 20,000 meters. The BLU-Fuze is conveniently packaged in the NATO standard fuze envelope for either artillery or mortar rounds so that it can add flight instrumentation and telemetry to a wide variety of munitions without any modifications to the munitions themselves. The BLU-Fuze is simple to use. The BLU-Fuze is activated when the battery pack is attached to the fuze body. The BLU-Fuze is then screwed into the fuze well of the projectile to be tested. Once activated, the BLU-Fuze will run for more than 45 minutes, providing ample time to verify the telemetry link, acquire GPS, load, and launch the projectile. Data is stored and transmitted after the round clears the bore beginning 100 msec before detection of the launch event.

  • MS2034A - VNA Master (Vector Network Analyzer)

    Company: Anritsu

    For field engineers and technicians who need all essential RF measurements anytime and anywhere, the MS2034A VNA Masters are the first and only truly portable handhelds with integrated 2-port vector network analyzer from 2 MHz to 4 GHz, spectrum analyzer from 100 kHz to 4 GHz, and power meter capabilities in a single instrument. Ideally suited for aerospace and defense application, the VNA Master offers valuable measurement capabilities that can replace obsolete instruments and improve operator mobility. In this way, field engineers and technicians can more quickly install, deploy, and maintain RF systems in the field. VNA Master is also an excellent solution for low-cost manufacturing and other general purpose applications given the broad frequency coverage, excellent performance, and integrated capabilities.

  • CMA 8800

    Company: Anritsu

    The CMA 8800 offers all the features of a mainframe OTDR in a rugged, economical, field-portable unit. When the CMA 8800 OTDR is configured with one of our many single-, dual-, tri- or quad-wavelength OTDR modules, it becomes the world's fastest OTDR for testing multimode or single-mode fiber. With a test range from 21 dB to 50 dB, you can test longer lengths with less averaging time. Along with dead zones as short as three meters, you can be sure you're getting complete and accurate data for your entire length of fiber. The optional Optical Switch, when used in conjunction with the S 918A bare ribbon fiber adapter, becomes the most efficient method for testing bare ribbon fibers. The built-in printer option allows the user to print the test results right in the field, saving valuable time. In addition, the GPIB Interface lets you conduct tests remotely, using a computer to control the CMA 8800 OTDR.

  • Master Family - Base Station Analyzers

    Company: Anritsu

    The BTS Master Base Station Analyzers are ideal for senior cell site technicians and RF engineers to accurately and quickly test and verify the installation and the commissioning of base stations and cell sites for optimal wireless network performance and for the on-going maintenance and troubleshooting to keep your wireless network infrastructure fine-tuned.The Cell Master from Anritsu is a comprehensive instrument that combines all of the tools required to simplify the job of deploying, maintaining and troubleshooting wireless base stations. A single, lightweight, handheld, battery-operated package, the Cell Master combines the functionality of a cable and antenna analyzer, spectrum analyzer, power meter, transmitter analyzer (CDMA, GSM and iDEN), transmission analyzer for 2-port devices, interference analyzer, GPS Antenna Tester and T1/E1 analyzer. Handheld, low cost, easy to use, field proven, the Cell Master covers it all.

  • Cable/Circuit/Lighting Arrester Test Device

    Company: Wuhan NANR Electric

    cable fault detector is to cater to industrial-grade power industry solutions and IT era of rapid development, the original cable fault tester limitations, using industrial embedded computer platform systems, network services, USB communication technology systematic, very greatly improve the instrument''s functions and use value and convenient on-site environmental operations. Especially for the growing number of buried cable provides a unique data management software. The entire system meets PRC power industry standard "DL/T849.1 ~ DL/T849.3-2004" special test equipment electrical equipment General technical conditions, the system is tested by the system host and the fault locator and meter three-part cable path for all kinds of power cable fault test, cable path, the depth of buried cables and cable testing archives to find the daily maintenance and management, as well as railways, airports and signal control cables, and streetlights accurate cable fault testing

  • CTS-M5 Series - microprocessor based transmitter

    Company: Automation Components

    The CTS-M5 Series has a microprocessor based transmitter. It uses an Electrochemical gas sensor to monitor a variety of gases. The CTS-M5 Series offers great value since it includes many standard features that can only be found as expensive options in other manufacturer's models. A digital display (LCD), push-button programming and on-board meter jacks are all standard. The transmitter provides an analog output of 4-20 mA DC or 2-10 VDC, proportional to the measured gas range, for transmission to the Building Automation System. The CTS-M5 Series offers flexibility and simplicity in one package. The relay setpoints may be seen as increasing or decreasing actuation simply by adjusting the deadband relationship. Set the deactuation point above the actuation setpoint and the CTS-M5 will automatically alarm on decreasing concentrations. Plus, calibration is extremely simple. First, apply the calibration gas and then adjust the potentiometer to the desired reading on the display.

  • NSG 4070 Series - EMC Immunity Test System

    Company: Teseq AG

    The NSG 4070 Series is a multifunctional EMC immunity test system. Its large frequency range from 9 kHz to 1 GHz and its modular set-up using internal or external amplifiers enable a large variety of applications including tests according to IEC 61000-4-6, various BCI applications as well as signal generator and power meter for test systems as per IEC 61000-4-3, IEC 61000-4-20, IEC 61000-4-21 and many other applications. The powerful and easy to use firmware makes the NSG 4070 independent from an external PC and control software, however it can also be remote controlled for system operation. A state-of-the-art data transfer of test and measurement data for documentation is provided by USB stick to be plugged into the front panel.

  • K706 - Digital Transceiver

    Company: Innovative Integration

    The K706 Digital Transceiver supports one FMC-1000 plug-in module providing two antenna inputs and four independent channels of DDC, two channels of DUC, and one spectrum analyzer embedded in a Xilinx Kintex-7 FPGA. It supports monitoring and/or recording of wide- or narrow-band spectra or channelized IF band data. The transceiver supports contiguous recording at 160 MByte/s until running out of disk space. Each DDC has its own programmable tuner, programmable lowpass filtering, gain control, and decimation settings, supporting output bandwidth up-to 100 MHz. Data is packetized in VITA-49 format with accurate timestamps, synchronous to an external PPS signal. Each DDC channel can be enabled and disabled on the fly to conserve host computer storage and bandwidth. An embedded power meter monitors the power (dBm) of the ADC inputs, supporting analog gain control of optional, user-supplied external front-end devices.

  • 3312 - Telecom Transformer Test System

    Company: Chroma ATE

    The 3312 provides 20Hz-1MHz test frequencies. In addition to transformer scanning test function, the 3312 has LCR Meter function. In test items, The 3312 covers most of telecom transformer's low-voltage test parameters which include telecom test parameters as Return Loss (RLOS), Reflected Impedance (Zr), Insertion Loss (ILOS), Frequency response (FR), and Longitudinal Balance (LBAL) etc.; primary test parameters of general transformer as Inductance, Leakage I nduc t anc e, Turns -R a t io, DC re s i s t anc e, Impedance, and Capacitance (between windings) etc.; secondary test parameters of general transformer as Quality Factor and ESR etc.; and pin-shor t test function. High-speed digital sampling measurement technology combined with scanning test fixture (A132501) design, improve low-efficiency telecom transformer inspection to be more accurate and faster.

  • KI-TK072A - Complete SM & MM Contractor Certification FiberTester Kit

    Company: Kingfisher International

    Kingfisher International is pleased to announce immediate availability of 5 Wavelength Optical Clean / Inspect / Test Kits, which are the perfect solution for contractors looking to work on multimode and single mode fiber optic systems including an additional test wavelength such as 1625 nm. The KI-TK072A - SM & MM Contractor Kit includes cleaning materials, a high quality x200 microscope, power meter and a 850 / 1300 nm LED & 1310 / 1550 / 1625 nm Laser Light Source, all fitted with interchangeable connectors, and powerful reporting software. The compact molded semi-rigid carry case is comfortable to use, provides good equipment protection, and also allows users to immediately identify if anything has been accidentally left out. It has additional space for an optional VFL and various test accessories.

  • CLEN096 - Oscilloscope

    Company: Nanjing Clean Energy

    CLEN096 has similar structure as CLEN062 but its performance has been significantly improved. Comparing to 062 CLEN 096 bandwidth is 5 times wider (5M vs 1M) and sensitivity is 10 times higher (10mV vs 0.1V). Particularly, its frequency meter has been greatly enhanced. It can measure frequency higher than 20MHz at sensitivity better than 0.2Vpp (062 can only take 5 - 6 MHz signal and requires TTL level). Another big improvement is that CLEN096 is battery-powered. Accepted voltage ranges from 2V to 5V so one regular 3.7V Li-ion or two 1.2V Ni-HM batteries can be used. It also comes with a built-in charger specific for 3.7V li-ion battery. CLEN096 has built-in USB-Uart converter which easy-off firmware upgrade and waveform upload. It can also run on USB power without battery.

  • MS500 Series - Handheld Oscilloscope

    Company: Shenzhen Micsig Instruments

    In handheld oscilloscope market, I am afraid that only Micsig handheld multi-function oscilloscope can be regarded as a true oscilloscope and others can be called scope only.Moreover, it’s function no less than desktop oscilloscope, as it designs lightweight and uses double injection plastic mould making oscilloscope high IP level; Real leather belt design, exclusively detachable battery design & supporting indoor & outdoor display mode make it become your good assistant in field working.Using 5.7 inches 640*480 pixels industry TFT LCD touch screen; Supporting button, touch and scroll wheels operation mode; Integrating scope, meter & recorder in one unit; Up to 190,000wfm/s capture rate & 240Kpts memory depth; Supporting including CAN,LIN,SPI,I2C,UART,1533B and 429 serial bus trigger & decode functions.

  • MS300 Series - Handheld Oscilloscope

    Company: Shenzhen Micsig Instruments

    If you want to buy an isolated handheld oscilloscope with a low budget, MS300 is your best choice absolutely.In handheld oscilloscope market, I am afraid that only Micsig handheld multi-function oscilloscope can be regarded as a true oscilloscope and others can be called scope only.Moreover, it’s function no less than desktop oscilloscope, as it designs lightweight and uses double injection plastic mould making oscilloscope high IP level; Real leather belt design, exclusively detachable battery design & supporting indoor & outdoor display mode make it become your good assistant in field working.Using 5.7 inches 640*480 pixels industry TFT LCD touch screen; Supporting button, touch and scroll wheels operation mode; Integrating scope, meter & recorder in one unit; Up to 50,000wfm/s capture rate & 240Kpts memory depth; Supporting including CAN,LIN,SPI,I2C,UART serial bus trigger & decode functions.

Products

Applications

Manufacturers