Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 5281 - 5295 of 5314 products found

  • NSG 4070 Series - EMC Immunity Test System

    Company: Teseq AG

    The NSG 4070 Series is a multifunctional EMC immunity test system. Its large frequency range from 9 kHz to 1 GHz and its modular set-up using internal or external amplifiers enable a large variety of applications including tests according to IEC 61000-4-6, various BCI applications as well as signal generator and power meter for test systems as per IEC 61000-4-3, IEC 61000-4-20, IEC 61000-4-21 and many other applications. The powerful and easy to use firmware makes the NSG 4070 independent from an external PC and control software, however it can also be remote controlled for system operation. A state-of-the-art data transfer of test and measurement data for documentation is provided by USB stick to be plugged into the front panel.

  • K706 - Digital Transceiver

    Company: Innovative Integration

    The K706 Digital Transceiver supports one FMC-1000 plug-in module providing two antenna inputs and four independent channels of DDC, two channels of DUC, and one spectrum analyzer embedded in a Xilinx Kintex-7 FPGA. It supports monitoring and/or recording of wide- or narrow-band spectra or channelized IF band data. The transceiver supports contiguous recording at 160 MByte/s until running out of disk space. Each DDC has its own programmable tuner, programmable lowpass filtering, gain control, and decimation settings, supporting output bandwidth up-to 100 MHz. Data is packetized in VITA-49 format with accurate timestamps, synchronous to an external PPS signal. Each DDC channel can be enabled and disabled on the fly to conserve host computer storage and bandwidth. An embedded power meter monitors the power (dBm) of the ADC inputs, supporting analog gain control of optional, user-supplied external front-end devices.

  • 3312 - Telecom Transformer Test System

    Company: Chroma ATE

    The 3312 provides 20Hz-1MHz test frequencies. In addition to transformer scanning test function, the 3312 has LCR Meter function. In test items, The 3312 covers most of telecom transformer's low-voltage test parameters which include telecom test parameters as Return Loss (RLOS), Reflected Impedance (Zr), Insertion Loss (ILOS), Frequency response (FR), and Longitudinal Balance (LBAL) etc.; primary test parameters of general transformer as Inductance, Leakage I nduc t anc e, Turns -R a t io, DC re s i s t anc e, Impedance, and Capacitance (between windings) etc.; secondary test parameters of general transformer as Quality Factor and ESR etc.; and pin-shor t test function. High-speed digital sampling measurement technology combined with scanning test fixture (A132501) design, improve low-efficiency telecom transformer inspection to be more accurate and faster.

  • KI-TK072A - Complete SM & MM Contractor Certification FiberTester Kit

    Company: Kingfisher International

    Kingfisher International is pleased to announce immediate availability of 5 Wavelength Optical Clean / Inspect / Test Kits, which are the perfect solution for contractors looking to work on multimode and single mode fiber optic systems including an additional test wavelength such as 1625 nm. The KI-TK072A - SM & MM Contractor Kit includes cleaning materials, a high quality x200 microscope, power meter and a 850 / 1300 nm LED & 1310 / 1550 / 1625 nm Laser Light Source, all fitted with interchangeable connectors, and powerful reporting software. The compact molded semi-rigid carry case is comfortable to use, provides good equipment protection, and also allows users to immediately identify if anything has been accidentally left out. It has additional space for an optional VFL and various test accessories.

  • CLEN096 - Oscilloscope

    Company: Nanjing Clean Energy

    CLEN096 has similar structure as CLEN062 but its performance has been significantly improved. Comparing to 062 CLEN 096 bandwidth is 5 times wider (5M vs 1M) and sensitivity is 10 times higher (10mV vs 0.1V). Particularly, its frequency meter has been greatly enhanced. It can measure frequency higher than 20MHz at sensitivity better than 0.2Vpp (062 can only take 5 - 6 MHz signal and requires TTL level). Another big improvement is that CLEN096 is battery-powered. Accepted voltage ranges from 2V to 5V so one regular 3.7V Li-ion or two 1.2V Ni-HM batteries can be used. It also comes with a built-in charger specific for 3.7V li-ion battery. CLEN096 has built-in USB-Uart converter which easy-off firmware upgrade and waveform upload. It can also run on USB power without battery.

  • MS500 Series - Handheld Oscilloscope

    Company: Shenzhen Micsig Instruments

    In handheld oscilloscope market, I am afraid that only Micsig handheld multi-function oscilloscope can be regarded as a true oscilloscope and others can be called scope only.Moreover, it’s function no less than desktop oscilloscope, as it designs lightweight and uses double injection plastic mould making oscilloscope high IP level; Real leather belt design, exclusively detachable battery design & supporting indoor & outdoor display mode make it become your good assistant in field working.Using 5.7 inches 640*480 pixels industry TFT LCD touch screen; Supporting button, touch and scroll wheels operation mode; Integrating scope, meter & recorder in one unit; Up to 190,000wfm/s capture rate & 240Kpts memory depth; Supporting including CAN,LIN,SPI,I2C,UART,1533B and 429 serial bus trigger & decode functions.

  • MS300 Series - Handheld Oscilloscope

    Company: Shenzhen Micsig Instruments

    If you want to buy an isolated handheld oscilloscope with a low budget, MS300 is your best choice absolutely.In handheld oscilloscope market, I am afraid that only Micsig handheld multi-function oscilloscope can be regarded as a true oscilloscope and others can be called scope only.Moreover, it’s function no less than desktop oscilloscope, as it designs lightweight and uses double injection plastic mould making oscilloscope high IP level; Real leather belt design, exclusively detachable battery design & supporting indoor & outdoor display mode make it become your good assistant in field working.Using 5.7 inches 640*480 pixels industry TFT LCD touch screen; Supporting button, touch and scroll wheels operation mode; Integrating scope, meter & recorder in one unit; Up to 50,000wfm/s capture rate & 240Kpts memory depth; Supporting including CAN,LIN,SPI,I2C,UART serial bus trigger & decode functions.

  • Function Generators

    Company: Shanghai MCP

    Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad

  • BB705 - Tempurature Reference Source

    Company: Omega Engineering

    This BB705 is a blackbody temperature reference source which is adjustable over the range from 100 to 1046°C (212 to 1915°F) and accurate to ±1°C, ±0.25% rdg. It has a built-in digital temperature controller to provide accurate, stable temperatures as well as to provide the temperature readings of the cavity. The heated cavity provides a target of known temperature and emissivity, and virtually any infrared pyrometer with a spot size diameter less than 44.5 mm (0.88") can be calibrated. Calibration setups are easy with the BB705. An independent NIST traceable probe and high accuracy panel meter provide temperature reference information. Both models come standard with an RS-232 computer interface which allows computer control of the setpoints for automatic test applications. A NIST traceable calibration certificate is also provided.

  • M-LINK - Monitors

    Company: Gentec Electro Optics

    The Universal Meter Reads ALL Heads: Power: Thermopiles, Photo Detectors and Pyroelectrics Energy: Thermopiles (in single shot mode), Photo Detectors and PyroelectricsMeasure fJ Energy LevelsThanks to a unique digital method for suppressing the noise on the lower rangesExternal TriggerSynchronize you M-LINK to your pulsed laser or digital chopperDigital (USB) OutputConnect the M-LINK module directly to your PCPowerful LabView Software Features include: Complete instrument controls: Range, Trigger, Wavelength, etc. Live display in J and J/cm2 or W and W/cm2 Full Statistics: Min, Max, Mean, Standard Deviation, RMS Stability , Repetition Rate, etc. Graphic Displays: Strip Chart, Histogram, Tuning Needle and more Data File Collection and Analysis

  • 1400 - Miniature EMI/RFI Shielding gasket

    Company: Holland Shielding

    This is a very small EMI/RFI-shielding gasket, used for EMI/RFI shielding on for example on PCB's, smartphones and other applications where little space is available.Miniature EMI/RFI shield (1400 serie Miniature shield)This EMI/RFI gasket can be produced in such small widths that the height exceeds the width. It has a sufficient electromagnetic damping.Application- on PCB's or printed circuit board's- other products where there is very little space available and low compression force is required.- EM, RF, LF, HF, EMI, RFI shieldingThe material is a highly electrically conductive foam with or without a electrically conductive self-adhesive strip at the bottom. The electrically conductive foam can be compressed by even more than 50 % of its original height.The smallest width is 1 mm and the maximum height is 6 mm. Roll length of 1 until 1000 meters. (Depending on width and height of the EMI gasket)

  • ETS-200T / ETS-200T-FT - Test System

    Company: Teradyne

    The ETS-200T / ETS-200T-FT discrete test platform is built on proven ETS technology and provides true index-parallel testing specifically for turret and rotary handlers. These test systems maximize throughput with pattern-based test techniques based on Eagle SmartPin™ technology coupled with the use of dynamic Cbits for enhanced user control. Both the ETS-200T and the ETS-200T/FT provides a complete test solution from wafer sort to final test for MOSFETs, including integrated control and datalogging for UIL, dVSD, Qg and LCR meter. Raptor™ software reduces program generation by providing a graphical user interface that does not require any programming experience combined with a robust set of test libraries and proven test techniques to increase test volumes and reduce cost of test.

  • Grain Tester

    Company: Hong Kong Joint Stars

    1.grain moisture meter,white led side backlight.2.multipoint calibration,display average data,volume weight,moisture and tempgrain moisture metercharacteristic:fast and accurate. have ac and dc power. white led side backlight. multipoint calibration, error correction.calculate average data, test volume weight. automatic weighing and temperature compensating. data output and calibration parameters download update. low energy consumption. auto and manual power-off.technical parameter:measuring object: cereal, mai lei, vegetable seed, soybean, Vegetables seed, corn, feed,flour and so on nonmetallic granulated mattertest accurate: ≤± 0.5repeat accurate: ≤ 0.2test range: 3~35%test time: ≤ 10stemperature compensation: internally installed sensistor automatic compensationuse temperature: 0~40°cnet weight:830gpower resource: 9v dc power or no.5 batterydisplay: backlight lcd

  • MFF-1 - RF Multifrequency Filter

    Company: ROM-Elektronik GmbH

    Since 2003 on the market and more current than ever! For us, it was already clear at this time what importance the service-specific analysis of high-frequency signals has and will have. We are very pleased that this vision has also found its way into the current SBM2008 (standard of construction-based measurement technology). The MultiFrequency filter MFF-1 enables precise measurement of common services - simply by means of a selector switch, without a large investment in a spectrum analyzer and without complicated settings on the device. The filter is simply connected between the measuring antenna and the HF meter - ready. The MFF-1 only allows the frequencies that are selected! There are six switch positions available: base stations D-network and E-network, DECT, base station UMTS, WLAN / Bluetooth, microwave oven and broadband (all frequencies).

  • SVM2 - Surface DC Voltmeter

    Company: Alpha Lab

    The SVM2 has high sensitivity (resolution), and can detect even a 1 volt charge anywhere within its full range of +29,999 to -29,999 volts. Thus it is easy to measure whether a given process is increasing or decreasing the static electricity present, even if the increase or decrease is by a tiny fraction. The meter reads the actual static signal, but it also captures and stores the highest positive and highest negative signals that were experienced since the last time that the "Reset" button was pressed. These peak + and can be displayed at any later time. The peak function has a "window" time of 0.005 seconds (which is much faster than the display) so even very quick peaks are captured and stored. There is also a user-settable alarm. The alarm will sound if the signal (whether + or -) ever exceeds the value set by the user for at least 0.005 seconds. The alarm can be reset or muted at any time.

Products

Applications

Manufacturers