Meters: sense and display measures of gas, water, electricity, particles, vibration or light.

Showing results 5296 - 5310 of 5314 products found

  • NSG 4070 Series - EMC Immunity Test System

    Company: Teseq AG

    The NSG 4070 Series is a multifunctional EMC immunity test system. Its large frequency range from 9 kHz to 1 GHz and its modular set-up using internal or external amplifiers enable a large variety of applications including tests according to IEC 61000-4-6, various BCI applications as well as signal generator and power meter for test systems as per IEC 61000-4-3, IEC 61000-4-20, IEC 61000-4-21 and many other applications. The powerful and easy to use firmware makes the NSG 4070 independent from an external PC and control software, however it can also be remote controlled for system operation. A state-of-the-art data transfer of test and measurement data for documentation is provided by USB stick to be plugged into the front panel.

  • 1400 - Miniature EMI/RFI Shielding gasket

    Company: Holland Shielding

    This is a very small EMI/RFI-shielding gasket, used for EMI/RFI shielding on for example on PCB's, smartphones and other applications where little space is available.Miniature EMI/RFI shield (1400 serie Miniature shield)This EMI/RFI gasket can be produced in such small widths that the height exceeds the width. It has a sufficient electromagnetic damping.Application- on PCB's or printed circuit board's- other products where there is very little space available and low compression force is required.- EM, RF, LF, HF, EMI, RFI shieldingThe material is a highly electrically conductive foam with or without a electrically conductive self-adhesive strip at the bottom. The electrically conductive foam can be compressed by even more than 50 % of its original height.The smallest width is 1 mm and the maximum height is 6 mm. Roll length of 1 until 1000 meters. (Depending on width and height of the EMI gasket)

  • K706 - Digital Transceiver

    Company: Innovative Integration

    The K706 Digital Transceiver supports one FMC-1000 plug-in module providing two antenna inputs and four independent channels of DDC, two channels of DUC, and one spectrum analyzer embedded in a Xilinx Kintex-7 FPGA. It supports monitoring and/or recording of wide- or narrow-band spectra or channelized IF band data. The transceiver supports contiguous recording at 160 MByte/s until running out of disk space. Each DDC has its own programmable tuner, programmable lowpass filtering, gain control, and decimation settings, supporting output bandwidth up-to 100 MHz. Data is packetized in VITA-49 format with accurate timestamps, synchronous to an external PPS signal. Each DDC channel can be enabled and disabled on the fly to conserve host computer storage and bandwidth. An embedded power meter monitors the power (dBm) of the ADC inputs, supporting analog gain control of optional, user-supplied external front-end devices.

  • 3312 - Telecom Transformer Test System

    Company: Chroma ATE

    The 3312 provides 20Hz-1MHz test frequencies. In addition to transformer scanning test function, the 3312 has LCR Meter function. In test items, The 3312 covers most of telecom transformer's low-voltage test parameters which include telecom test parameters as Return Loss (RLOS), Reflected Impedance (Zr), Insertion Loss (ILOS), Frequency response (FR), and Longitudinal Balance (LBAL) etc.; primary test parameters of general transformer as Inductance, Leakage I nduc t anc e, Turns -R a t io, DC re s i s t anc e, Impedance, and Capacitance (between windings) etc.; secondary test parameters of general transformer as Quality Factor and ESR etc.; and pin-shor t test function. High-speed digital sampling measurement technology combined with scanning test fixture (A132501) design, improve low-efficiency telecom transformer inspection to be more accurate and faster.

  • M-LINK - Monitors

    Company: Gentec Electro Optics

    The Universal Meter Reads ALL Heads: Power: Thermopiles, Photo Detectors and Pyroelectrics Energy: Thermopiles (in single shot mode), Photo Detectors and PyroelectricsMeasure fJ Energy LevelsThanks to a unique digital method for suppressing the noise on the lower rangesExternal TriggerSynchronize you M-LINK to your pulsed laser or digital chopperDigital (USB) OutputConnect the M-LINK module directly to your PCPowerful LabView Software Features include: Complete instrument controls: Range, Trigger, Wavelength, etc. Live display in J and J/cm2 or W and W/cm2 Full Statistics: Min, Max, Mean, Standard Deviation, RMS Stability , Repetition Rate, etc. Graphic Displays: Strip Chart, Histogram, Tuning Needle and more Data File Collection and Analysis

  • ESP - Dual Camera Borescope

    Company: Autonology Co. Ltd

    Clear viewing on 3.5'' LCD monitor with QVGA resolution. 9mm diameter camera head; 1 meter long soft metal probe with 640 x 480 pixel (VGA) resolution camera. Camera lightingSIX white LED light provide glare-free lighting in any environment. Probe and stainless steel camera head are IP67 water, oil and dust-proof.Powered by 18650 Li-Ion Battery (2600mAh) continuous operation about 7 hours. The scientific button design make it easier during the operating. Specification Insertion Probe Diameter of Camera Head 9 mm. CMOS sensor1/8'' CMOS chip. Camera Resolution640 x480 pixel. Camera LightingMicro LED with intensity adjustment 6 White LED. Lightness manual adjustment wayYes. Field of Viewing angle (FOV)90. Camera Depth of Field 15-100mm . Probe Length1m (39 in.). Probe Material shapable soft metal.

  • Dl1 RS-485 - Data Collection Recorder

    Company: Chang Shuan Electronics

    DL1 is design to communicate through RS485 to read variety of devices (Such asinstrumentation, PLC, A / D conversion card ....) and stored the data collected into a SD card.Data can then be converted to Excel file format on a computer to perform analysis and production of related reports needed by users. This product not only read and record data speed up to 0.1 seconds, and its flexible software setting allows in many ways for easy planning. For multiple projects user, DL1 provide two project planning procedures which stored the data into two separate files. After all setting on software, parameter can be upload/download to DL1 using a USB interface cable. Recording can be start by external DI contact or by meter button. ADPro is the software provided with the hardware for setting parameters and procedures planning through the USB interface cable to the DL1. Today there are lots of field (such as industrial, energy, environment monitoring,commercial information ....),needs record process data, providing DL1 is rather inexpensive solution compare to present industrial recorder. DL1 give a simple, convenient and economical solution for all.

  • Redundant Power Packages

    Company: Acopian Technical

    An Acopian Redundant Power Package is installed by simply connecting the AC input and DC output terminals. All wiring (including isolation diodes, output monitor circuits, switches, meters, adjustments and connectors) has been done for you.Output Redundancy: Each Redundant Power Package contains two identical power supplies with their outputs interconnected through a diode switching arrangement that will detect any fault condition, isolate it from the system output, and pass only the output of the other supply with no interruption of output power during the transition.Input Redundancy: All Acopian Redundant Power Packages may be operated with only one AC power source. However, two isolated sets of AC input connections are provided, so that two independent sources of input power may be used, to obtain the additional protection of input redundancy. A battery- backup power source (UPS) and/or a second power line from the power utility can be used to maintain output power without interruption when your primary source of AC power fails.Applications: Redundant Power Packages should be considered for any equipment where the highest attainable reliability is essential, and an unexpected loss of power would be disastrous. Such applications include communications systems (both voice and data types), computer systems (volatile memory systems in particular), process controls, utility and municipal systems, and security/safety alarm systems.

  • 6041G-HD - SDI video inserter

    Company: Instrumentation Technology

    The Model 6041G-HD is a ruggedized SDI video inserter. When the unit is placed within 100 meters of an SDI video source, the 6041G-HD enables accurate time stamping of each video frame/field. Time stamping prior to any compression and transmission of the SDI stream from a remote source such as a range camera, ensures that time recorded is accurate to within 10 microseconds of the frame or field sync.. Since the unit reclocks the SDI stream, it may also be used as a repeater extending the distance from the SDI video source to the transport insertion equipment (compressor, Ethernet, or other transport means). The unit auto-detects and decodes the imaging format permitting most SDI 480i/p, 720p or 1080i/p NTSC or PAL sources to be connected without having to change system settings. The time message may be inserted into the active video image, with the color (1 of 16) and location selected by the user. When selected, the time is also inserted into the SDI meta-data (vertical ancillary packets) in accordance with MISB STD 0605.3 and NATO STANAG 4609. The time reference is derived from either the internal GPS receiver or an external IRIG B time code source. If the GPS or IRIG lock is lost the unit will automatically continue to run on an internal clock.

  • RF Power Amplifier Automatic Measurement System

    Company: Acery Technologies

    RF power amplifier automatic measurement system consists of a new generation of science and technology is the German spectrum analyzer, RF and microwave signal source, network analyzers, noise figure analyzers, power meters, digital oscilloscopes, high performance DC power supplies, multimeter, low-frequency switching and digital I / O, custom RF and microwave switch matrix and other equipment and related equipment. These high-performance equipment not only provides incentives and analysis for the amplifier under test, but also provides a DC power supply and power amplifier circuit and other peripheral adjustment necessary. Meanwhile, the system sets the test signal conditioning, configuration and calibration test as one of the major parameters which can be accurately amplifier, fast and flexible testing. All equipment is controlled by the core of the test system software can be fully automated production test and manual type of R & D design type tested to meet the testing requirements of different stages. System software includes a convenient test mode conversion, simple and clear path and test switch interface, the main instrument soft front panel measuring device, and a measurement report in line with MS Word and Excel format and other functions.

  • HD-TVI Tester

    Company: Fuzhou Metricu Technology

    IP camera tester with capacitive touch screen, display ONVIF IP camera image, ONVIF PTZ controller, support more than 40 customized IP cameras protocols, support video management software to view IP camera image, built-in WiFi to receive network image and data, FTP Server, Static IP address, DHCP, simultaneously test different segments´ IP cameras, Network bandwidth testing, PoE 24W power supply to IP camera, PoE voltage testing, HDMI signal output, support 1080P, support DC12V 2A power output to camera, USB 5V 2A power output to mobile phone, video level meter, cable tracer to find cable from messy cables, PoE port finder, link monitoring, ip camera´s ping testing, ip address scan, BNC input & output, both IP and analog images could be zoomed in 1-4 times and output, support snapshot, video recording and playback, built in 4G SD card, NTSC/PAL auto-selecting, video signal measurement,analog PTZ control, preset setting, UTP cable testing, PTZ data analyst, RS485 communication address scan, audio input testing and output, Led lamp, 7.4V DC 6600mAh lithium polymer battery, working for 17 hours, HD-TVI camera testing etc.

  • Unisim Compact Solar Simulator - Solar Simulator

    Company: TS Space Systems

    The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.

  • FTE-5000 - Loss Test Set

    Company: Terahertz Technologies

    The FTE-5000 is a full featured ORL Loss Test Set. It has 4” super bright color touch screen display with large easy to read characters. It performs optical return loss measurements to -55db at up to three wavelengths and is an automated loss test set with dual or triple wave Light sources. The power meter uses an InGaAs detector which is calibrated at 850,1300, 1310, 1490, 1550 and 1625nm, with a dynamic range of -77dBm. These units are available in single, dual, triple or quad wavelength configurations and displays measurements up to three wavelengths at one time. In the Autotest mode, the master unit changes wavelengths at a fixed rate and informs the slave unit of the wavelength currently being measured. Use this method to test up to three wavelengths at a time and store the loss measurements for each of the lasers fired during the test. Up to 5000 tests may be stored and recalled via the unit’s USB port. Use TTI’s CertSoft PC application software for downloading stored data and organizing the information or use the Android Bluetooth virtual instrument application for remote operation.

  • TL81A - Deluxe Electronic Test Lead Kit

    Company: Fluke

    The TL81 kit consists of a quadfold nylon pouch containing two each (one black and one red) of the following items: One meter long test lead with a safety shrouded, right angle banana connector on one end and a stainless steel test probe on the other end, rated up to 10A. Silicone-insulated leads have superior flexibility in cold temperatures and resistance to high temperatures. Insulated alligator clip rated up to 5A. Insulated probe tip extender rated up to 3A. Modular test probe with banana connector in the handle, rated up to 10A. Modular hook-style clip test lead with banana connector, rated up to 5A. Modular pinch-style clip test lead with banana connector, rated up to 5A. Modular alligator clip with banana connector, rated up to 5A. Slide-on IC probe tip adapter (rated up to 3A) and test lead couplers. Bare spade lug with banana connector, rated up to 10A. CAT III 300VCompatible with Fluke and other multimeters that accept safety shrouded, standard diameter banana connectors. UL approved.One year warranty.

  • VGM - Vector/Magnitude Gaussmeter

    Company: Alpha Lab

    The Vector Gaussmeter displays the true magnitude of the field at any location as well as the X, Y, Z components of up to 800 gauss. Also separately displays peak values of X, Y, Z, and magnitude. There is a sound alarm that determines the locations where the field magnitude exceeds user-set threshold. Because magnitude is measured, the orientation of the sensor (E-W, N-S, and up-down) is not important; this is unlike a 1-axis gaussmeter. With the VGM the user can set the alarm to 15 gauss (for example) and it will sound (simultaneous with a red light) whenever the field exceeds 15 gauss for at least 5 milliseconds. Using the meter this way, it is easy to make a map of the 15 gauss line (or for whatever threshold is set) around a strong magnet. When using the alarm, of a steel part can be rapidly scanned to show if any areas exceed the set threshold. Then the "peak hold" function can be interrogated, showing the peak values of X, Y, Z (including polarity) and magnitude that occurred during the scan. Peak hold also has a 5 millisecond response time.

Products

Applications

Manufacturers