Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing results: 4936 - 4950 of 4962 items found.

  • SparkFun GPS Breakout

    NEO-M9N, Chip Antenna (Qwiic) - SparkFun Electronics

    The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations witn ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

  • SparkFun GPS Breakout

    NEO-M9N, U.FL (Qwiic) - SparkFun Electronics

    The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

  • SparkFun GPS Breakout

    NEO-M9N, SMA (Qwiic) - SparkFun Electronics

    The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

  • LED Driver Aging Rack

    LEDRACK-100W192P - Lisun Electronics Inc.

    • Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)

  • Radiator Flow Test Machine

    8601 - Hydraulic Technology, Inc.

    The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.

  • Function Generators

    Shanghai MCP Corp

    Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad

  • Motor & Drive Troubleshooting Kit

    Extech MG302-MTK - Extech Instruments Corporation

    The Extech MG302-MTK Motor and Drive Troubleshooting Kit includes three compact tools for troubleshooting three phase motors and drives. The first tool in the kit is the MG302, a 13 Function Wireless True RMS Multimeter/Insulation Tester featuring 125 V, 250 V, 500 V, and 1000 V test voltages. It also features insulation resistance from 0.001 MOhm to 4000 MOhm, auto discharge of capacitive voltage, a lock power on function for hands free operation, data hold, min/max, relative mode, auto power off and more at a CAT IV 600 V safety rating. The second tool is the 480403 Motor Rotation and Three Phase Tester that features a double molded, durable housing and CAT III 600 V safety rating. The third tool in this kit is the MA435T 400 A True RMS AC/DC Clamp Meter with a built in non-contact voltage detector, 10 functions and a CAT III 600 V safety rating.

  • Handheld Audio Analyzer

    PAA3X - Phonic Corporation

    The PAA3X is a highly accurate handheld audio analyzer that gives sound engineers a rich array of sound analysis tools. The system features both 61-band and 31-band real time spectrum analysis, RT60 reverb time measurement, SPL and line meter, internal signal generator, EQ setting program, microphone calibration and speaker phase checking abilities. All functions and menus can be accessed through a central jog dial, leaving your other hand free to adjust audio settings. The large color LCD screen has an adjustable brightness to help you see in a dark or well-lit environments alike. The PAA3X also features a "screen capture" function allowing users to save images of the screen to an SD card in BMP format for later reference. The detachable precision microphone can be placed remotely via the included 5-meter extension cable, offering flexible on-site operation management. With all this plus a built-in rechargeable lithium-ion battery, the PAA3X is a must-have multifunctional tool for all serious audio engineers.

  • LED Power Driver ATS

    8491 - Chroma ATE Inc.

    1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series

  • Environmental (Radiation) Monitoring System

    Hawk® EMS - International Medcom

    The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.

  • Digital RF Power &VSWR Measurement System

    PowerMaster II - Array Solutions

    Thank you for purchasing the Array Solutions PowerMaster II RFPower/VSWR Indicator. The PowerMaster II represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster II also features the ability to be monitored and controlled from a PC using the software downloadable from our website, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster II firmware updates will be posted for download from the Array Solutions website as they become available. This means that the user can take full advantageof features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates

  • Digital RF Power &V.S.W.R. Indicator

    PowerMaster Series - Array Solutions

    Thank you very much for purchasing the Array Solutions PowerMaster Series RF Power/VSWR Indicator. The PowerMaster represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster also features the ability to be monitored and controlled from a PC via the bundled software, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster firmware updates will be made available for download from the Array Solutions website as they becomeavailable. This means that the user can take full advantage of features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates.

  • Proactive Downstream Spectrum Analysis

    SpectraVizion - ZCorum

    SpectraVizion is an innovative, software-based diagnostics tool that leverages new advancements in remote spectrum capture, allowing cable operators to address downstream spectrum impairments proactively, before subscribers call in with service complaints. “Troubleshooting downstream spectrum issues has always been a reactive process for cable operators,” said Arthur Skinner, Vice President of Worldwide Sales for ZCorum. “Often they’re not aware they have an issue until a customer calls, and that’s when they then send a technician to the home with a hand-held meter to start a search for the problem.” SpectraVizion takes the guesswork out of problem identification and location by presenting on a simple dashboard a list of devices that are experiencing common downstream issues like Standing Waves, FM Noise, Suck-outs, Roll-off and Tilt. The tool leverages the spectrum data available from cable modems and set-top boxes that support full band capture, and advanced detection algorithms automatically identify devices experiencing downstream impairments. The operator can click on any device in the list to view a capture of the full spectrum from that day, or up to 30 days in the past.

  • Thermocouple Vacuum Gauge for High Vacuum

    DV-5 Series - Teledyne Hastings Instruments

    ​Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-5 series thermocouple vacuum gauge tube/sensor can be paired with a variety of meters or controllers in the DV series to provide reliable, cost effective measurements in a variety of applications. The robust, easy to install gauge system translates a thermoelectric voltage to a vacuum pressure based on the density of the gas. The thermocouple gauge tube/sensor, DV-5, is fully compensated for temperature and rate of temperature change with no suspended weld to an external heater.The gauges are calibrated for nitrogen or air, but conversion factors for other gases are available from the factory. The thermocouple gauge or controller does not require recalibration when thermocouple gauge tubes are replaced further decreasing process down time. However, our DB-18 reference tube is available to confirm meter/controller performance. Installation accessories are also available from the factory to support your installation needs. One less thing to worry about, when performance matters!

  • Vacuum Sensor, Thermocouple Vacuum Gauge for High Vacuum

    DV-5 Series - Teledyne Hastings Instruments

    ​Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-5 series thermocouple vacuum gauge tube/sensor can be paired with a variety of meters or controllers in the DV series to provide reliable, cost effective measurements in a variety of applications. The robust, easy to install gauge system translates a thermoelectric voltage to a vacuum pressure based on the density of the gas. The thermocouple gauge tube/sensor, DV-5, is fully compensated for temperature and rate of temperature change with no suspended weld to an external heater.The gauges are calibrated for nitrogen or air, but conversion factors for other gases are available from the factory. The thermocouple gauge or controller does not require recalibration when thermocouple gauge tubes are replaced further decreasing process down time. However, our DB-18 reference tube is available to confirm meter/controller performance. Installation accessories are also available from the factory to support your installation needs. One less thing to worry about, when performance matters!

Get Help