Filter Results By:
Products
Applications
Manufacturers
-
product
Environmental Test Chambers
ET-Series
Environmental Test Chambers are designed with uncompromised features included in the system to meet your changing application needs of simulation of wide range of temperature, relative humidity etc., conditions without the added cost of expensive add-on’s as options. Available in varied volumes to fit your differing specimen sizes
-
product
In-Process Test OTDR
8000i
The 8000i In-Process Test OTDR is the most recent addition to Photon Kinetics' family of innovative solutions for optical fiber cable testing. The 8000i's "cable test optimization" provides the balance of OTDR dynamic range and dead zone performance that's proven to be most effective for accurate characterization of typical fiber cable lengths. Dynamic range has been maximized to reduce measurement time, while resolution has been tuned to ensure that typical cabled fiber defects are detected. The 8000i delivers this optimized measurement capability at a more economical price than our full featured, final QC 8000 OTDR, which makes it a perfect fit for "in-process" testing on ribbonizing or loose tube production lines.
-
product
PD Test Systems
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
product
Radio / Conformity Tests
The safe and effective use of radio frequencies (HF), referred to in English as radio frequencies (RF), must be checked for every device with integrated radio technology. The legal requirements for radio frequency (HF) tests vary depending on the use of the device (medical devices, automotive and telematics devices, cellular devices, etc.).
-
product
Strain Gauge Test
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
product
Terminals And Test Points
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
product
Antenna Test Facility
Raytheon’s Antenna Test Facility (ATF) provides state-of-the-art measurement capabilities to assist in the development of advanced antenna technologies for a variety of airborne and space applications such as advanced radar and communication systems. The ATF is available for use by Raytheon businesses as well as other companies that design and prototype new and experimental antennas.
-
product
Test Power Rectifiers
Kinetics has designed and manufactured various types of power rectifiers for traction test applications that include both power and electronic loads. Kinetics’ engineers will use our extensive application experience to work with an application’s specifications for the design and manufacture of a testing unit that provides the optimum power system for a customer’s application.
-
product
Flexible Test Connectors
Pin and socket sizes 22, 20, 16, 12 and 8 conform to MIL Spec dimensions. Whenever connector reliability is important, you’ll find NASA-approved FLEXCON test connectors. Applications include electronic, electrical and communications systems, computers, space vehicles, missiles, aircraft and other military equipment.
-
product
Hydrostatic Test Chambers
Test chambers are available to protect personnel during proof or burst testing. A few samples are pictured below. Chambers are manufactured in polished stainless steel with a clear polycarbonate door(s) for visibility during testing. Fluid port(s) are provided inside the enclosure, while all controls remain outside the enclosure for operator safety. In a hurry? Choose from our selection of Quick Ship Test Systems. basic units can ship within 24 hours or less and chamber systems within 2-3 days. we normally stock test chambers with nominal working area dimensions of either 24" wide x 24" deep x 15" high, 36" x 36" x 15", 48" x 24" x 15" or 72" x 24" x 12" with the door opening from the top. specify individual parameters at our customization page. Need a different size or configuration? No problem, simply specify dimensions and features that more accurately meet your particular requirements and we will be pleased to accommodate you. To customize a system to fit your particular application, please visit our customization page or give us a call at (916) 645-3317.
-
product
Automatic Test Equipment
Wewon Environmental Chambers Co, Ltd.
Automated Test Equipment (ATE) adopts PID+PWM principle VRF (Refrigerant flow control) technology to realize low temperature and energy saving operation (servo control technology of refrigerant flow based on thermal condition of electronic expansion valve). Realize the automatic constant temperature of the studio.https://www.wewontech.com/automatic-test-equipment/
-
product
Fiber Test & Measurement
Thorlabs manufactures a range of devices for testing and measuring the performance of optical fiber. Power, spectral signature, polarization, or end face surface geometry can by characterized with out-of-the-box solutions from our catalog. EO modulators, optical switches, and light sources are available to treat light being used on a test bed.
-
product
Modular Test System
DMT
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
product
Other Test Systems
Your business challenges do not fit the typical mold. Your test requirements are different. Ball Systems has more than 50 years of experience in multiple industries that has exposed our team to a wide variety of testing applications. As a result, we’ve likely created a solution for a challenge similar to yours.
-
product
Sine Reduction Test
Sine Reduction Test - Sine Processing With COLA SignalIntegrate and synchronize the data acquisition system seamlessly with your vibration shaker COLA signal and perform a powerful evaluation of structural properties on unlimited channels in real-time. The Dewesoft sine processing solution is easy to set up and will get you measuring right away.
-
product
Flight Test Switches
Curtiss-Wright Defense Solutions
Our compact, deterministic flight test switches have been qualified to reliably deliver high-speed, real-time data with a wide temperature operation ranging from -40 to 85°C. Their rapid boot-up capability minimizes data loss from power outages, while their flexible forwarding and filtering configurations can send what is required to multiple destinations for real-time monitoring, recording, and transmission. Our selection of flight test switches includes support for IEEE-1588 PTP, embedded v1 and v2 Grandmaster support and translation, and GPS and digital IRIG-B input and output. We also offer additional hardware to translate between PCM/CAIS and Ethernet to help protect existing hardware investment and have participated in the TmNS program by developing leading-edge technology for complete network monitoring and control.
-
product
Standard Test Systems
WaveCore™ Products
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
-
product
Cable Test Van
BAUR Transcable 4000/S 70-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
product
Handover Test Systems
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
-
product
Chloride Test System
C-CL-2000
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
product
Memory Burn-In Test
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies.
-
product
Distortion Test Sets
DTS-C
Matrix Test Equipment Incorporated
The Model DTS Distortion Test Sets combine Matrix products with those of other manufacturers. When properly equipped, a Model DTS can measure virtually any parameter important to the CATV industry. Controlled completely through the (GPIB) IEEE-488 bus interface, a Model DTS allows rapid, repetitive, and objective readings in a production-type environment.
-
product
CFML Test Framework
TestBox
TestBox is a next generation testing framework for ColdFusion (CFML) that is based on BDD (Behavior Driven Development) for providing a clean obvious syntax for writing tests. It contains not only a testing framework, runner, assertions and expectations library but also ships with MockBox, A Mocking & Stubbing Framework. It also supports xUnit style of testing and MXUnit compatibilities.
-
product
Leak Test System
NorCom 2020
The NorCom 2020 batch inspects up to 500 devices per cycle for both gross and ultra-fine leaks. The system incorporates a patented full field interferometer that produces reliable, repeatable leak test results. The system eliminates the need for helium mass spectroscopy or krypton testing for fine, and bubble leak testing for gross leaks.
-
product
Cable Test Van
BAUR Transcable 4000/S 110-1
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
product
Video Test Hardware
The first integrated test equipment for testing DP Alt Mode in USB Type-C sinks and sources. UCD-340 features a flexible and robust way of testing video, audio and power delivery functions of USB‑C. The provided software enables user access to the vital parameters and controls needed when evaluating the various functions of the interface.
-
product
Switching Test Set
U3020AS26
The Keysight U3020AS26 is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
product
Triaxial Test Set
Two measuring methods are used for measurement of screening efficiency - Transfer impedance, Screening attenuation. EC (European Cabling) Group of DELTA has during the last years supplied many customers with test fixtures for measurement of transfer impedance. The use of the fixture has now been extended to comprise screening attenuation measurement according to the triaxial method.
-
product
UAT Test Management
User Acceptance Testing is the final stage of the Software Development Life Cycle, which is conducted by the users. User Acceptance Testing is extremely important to determine whether the project is working fine as per the end user's point of view. The UAT test management process has to be done in an organized manner to reap maximum benefits from the process.
-
product
Digital Test Switch
FT-14D
Test switch solution for digital switchgear using current and voltage sensors. With the FT-14D Digital FlexitestTM switches, a new era of protection relay testing can be performed more safely, quickly and easily. The FT-14D switch allows a customer to integrate current and voltage sensors within digital switchgear and protective relays and thereby enable the Industrial Internet of Things.