Showing results 1486 - 1500 of 5664 products found

  • ST90 - Fiber Continuity Tester

    Company: Elenco Electronics

    Clips conveniently into a shirt pocket. Krypton light is extremely bright, yet much safer than laser sources. Tester acts as inspection back light. Operates on 2 AA batteries (not included).Powerful Krypton light source provides long range over multimode fiber.Soft ferule gripping membrane is designed to protect finished ferrules while firmly securing the connector in the tester body.

  • Ground Resistance Testers

    Company: AEMC Instruments

    Whether you are doing a simplified 2-Point, a more complete 3- or 4-Point Fall-of-Potential test, a soil resistivity test or a touch potential test, AEMC® has the right instrument for you. Our revolutionary clamp-on ground resistance tester will save you both time and money. Whichever AEMC® ground tester you choose, you can count on it to be the highest quality, the most complete package and the simplest to learn to use.

  • Inspector 920 - Electrical / Air / ABS Tester

    Company: Lite-check

    The Advanced ABS diagnostic trailer tester with brake and light testing takes the guesswork out of trailer repairs. LITE-CHECK 3-Step ABS Process will cut ABS troubleshooting time in determining ABS problems. The Inspector 920 includes all of the PLC ABS codes dating from 2001 and with the latest Roll Stability codes eliminating multiple operations and tools in one simple process. The tester automatically identifies the ABS ECU issues and displays the necessary information to make repairs.

  • Motorcycle Battery Testers

    Company: ELAK Private Ltd

    ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery – full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.

  • MB Model - Multi-Operational Surge Tester

    Company: PJ Electronics

    Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.

  • ESPIER2001 - Open / Short Tester

    Company: Tokyo Electronics

    There is a requirement of fast DC test such as open/short of any DUT pins, though complete performance test is not requested. Simplified test before and after burn-in, screening before the final test or before shipment are some of these examples. For this type of application, fast and inexpensive open/short tester is more suitable than the full DC tester that has plentiful test functions.

  • OmniTest Universal Hardness Tester

    Company: Qualitest International

    The OmniTest Universal Hardness Tester is designed to meet the increasing demand of versatility for the laboratory or quality control station. The unique design and advanced features eliminates operator influence during indentation measurement, thus assuring the highest repeatability. The combination of cutting edge technology and ease-of-use make the OmniTest with fully automatic image evaluation the obvious replacements for traditional mat-screen testers.

  • PT-55 - Peel Force Tester

    Company: V-Tek

    V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.

  • 501 - Pencil Hardness Tester

    Company: Elcometer Limited

    The Elcometer 501 Pencil Hardness Tester has been designed to ensure that the cylindrical pencil lead is maintained at a constant angle of 45° and exerts a force of 7.5N (1.68lbF).The pencil lead, prepared beforehand using the special sharpener and abrasive paper, is inserted into the Elcometer 501 hardness tester and pushed over the smooth, flat coated surface.The lowest hardness value of the pencil which marks the coating determines the coating’s hardness rating.

  • NI Series - Pendulum Impact Testers

    Company: NCS Testing Technology

    NI Series Pendulum Impact Testers are used to detect the impact resistance of metal materials under dynamic loads. It can conduct large quantities of metal impact tests continuously, display the impact absorbing energy and pre-elevation rotation angle of the pendulum and print test reports. It is useful not only for manufacturers of metal materials and quality inspection organizations, but also for research institutes for analsysi of new materials. It can use automatic sampling system to greatly improve the test efficiency and reduce the labor intensity of testers.

  • P-GW Functional Tester

    Company: Polaris Networks

    The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.

  • 39004 - SOHOTest-E - Residential Cable Tester

    Company: C2G Lastar

    The SOHOTest-E (Small Office Home Office) tester is an economic solution to test the most commonly used cables in residential wiring, those with f-type and RJ45 connectors. Use this handy tester to determine wiring faults in network, phone and cable TV cables before or after installation in cable installations up to 200 meters (656 feet). Has a compact, lightweight design with a small form factor of 2in x 3in x 1in. Uses a pass/fail coaxial test. Includes a remote unit for single person testing.

  • S-GW Functional Tester

    Company: Polaris Networks

    The LTE SGW Functional Tester provides a wrap-around test solution for the Serving Gateway by emulating all the LTE network elements surrounding the SGW (System Under Test). The S-GW Functional Tester emulates an LTE eNodeB and other Core Network entities such as the MME, P-GW, S-GW, RNC and SGSN. It tests the S1-u, S11, S5/S8 , S12 and S4 interfaces of the S-GW.

  • Shoe Dielectric Resistance Tester

    Company: Qualitest International

    The Shoe Dielectric Resistance Tester is designed to test the dielectric resistance of safety or other ways insulated footwear. The Shoe Dielectric Resistance Tester applies a power (line) frequency voltage between the inner and outer electrodes of the shoe (specimen) being tested, if the test specimen does not fail, the current in mA displayed on the ammeter is the leakage current; the voltage in kV indicated by the voltmeter is the withstanding voltage. It adopts HMI,so operation is smart and visible.

  • Shoes and Wrist Strap Tester

    Company: Eurostat Group

    • Our economical version of a shoes & wrist strap tester for mobile use or wall mounted• Compatible with all types of connection: 7 / 10 mm studs, banana or GSGS plugs (4.5mm studs in option)• Indicates whether resistance is too low or too high (no separate test between shoes and wrist strap)• Works with batteries supplied with the tester• Low battery indicator

Products

Applications

Manufacturers