Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 1576 - 1590 of 4608 products found.

  • Solar Cell Testers

    Photo Emission Tech., Inc.

    Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.

  • Quad Port Ethernet/IP Tester

    PacketExpert - GL Communications Inc.

    GL's PacketExpert is a portable Quad Port Ethernet Tester (USB based) with 4 Electrical Ethernet Ports (10/100/1000 Mbps) and 2 Optical Ports (1000 Mbps). The portable Ethernet/IP tester connects to Notebook PC through a USB 2.0 interface. Each GigE port provides independent Ethernet/IP testing at wirespeed for applications such as BERT, RFC 2544, and Loopback. It truly takes confusion out of Ethernet testing at all protocol layers - from raw Ethernet frames to IP/UDP packets. It can be used as a general purpose Ethernet performance analysis for 10 Mbps, 100 Mbps and 1 Gbps Ethernet local area networks. Two of the 4 ports have both Electrical and optical interfaces, enabling testing on optical fiber links as well.

  • Tensile Strength Tester

    Atico Export

    Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.

  • Vickers Hardness Tester

    Mitech Co., LTD.

    Digital vickers hardness tester, based on the principle that positive quadrangular pyramid diamond indenter presses the surface of the sample to produce indentation.By measuring the diagonal length of the indentation to achieve the measurement of the hardness of the material can be for small specimens, thin specimens, surface coating, heat treatment of the workpiece surface Vickers hardness test. With stable performance, strong structure, high reliability, simple operation, adopt digital display and high magnification optical measurement system, adjust the cold light source, photoelectric sensing technology and computer-aided means it has a powerful function. It is widely used in the fields of metal processing, electronics industry, mold parts, watch manufacturing, engineering quality inspection and so on. It is an ideal hardness tester for material research and testing.

  • Bit Error Rate Tester

    C-BERT 2860-4 - Munich-Instruments GmbH

    The C-BERT 2860-4 is a new kind of bit error rate tester for 100G Ethernet optical transmitters and TOSA. The new test instrument has four built-in optical to electrical receivers to provide an optical reference receiver functionality in the BERT. The optical receivers have 4th order Bessel-Thomson characteristics to perform a compliance eye mask tests with the fast BERT eye scan mode of the C-BERT. In addition the OMA and the extinction ration are extracted from the four BERT eye scan diagrams and the detector current. The vertical eye width and eye height are measured at a given bit error rate is as well. The C-BERT 2840-4 combines four pattern generators, optical reference receivers and eye mask testers in one compact instrument to eliminate expensive sampling oscilloscopes and to implement a fast and cost efficient transmitter test solution in production and lab.

  • Ultra-Compact Immunity Tester

    AXOS5 - Laplace Instruments Ltd.

    The AXOS5 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS5 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.

  • Ultra-Compact Immunity Tester

    AXOS8 - Laplace Instruments Ltd.

    The AXOS8 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS8 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.

  • Foot & Wristband Tester

    E3 - Elme S.r.l.

    E3 Dual ESD Tester for bands and footwears. E3 has been designed to test the performance of ESD wrist bands and footwears such as shoes or footgrounders. E3 is designed to operate tests in accordance with IEC 61340-5-1:2007 standard.E3 performs test on the ESD wristband and the ESD footwears automatically, with separate test for left and right foot. The operator can easily select the test to perform (band only - shoes only - shoes and bands together). E3 includes a dual large and comfortable foot plate (for left and right foot). E3 shows results as High, Pass, or Low resistance values. A relay output can easily connect to electrical doors opening for access in restricted EPA areas. E3 works with battery or external power supply (220 or 110V). The kit includes the tester, the wall mount yellow panel, the dual foot-plate, all cords and , with SPS version, the power supply.

  • Low Gauge Vacuum Tester

    G4103 - Gunson

    Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)

  • Air Permeability Tester

    TF164B - TESTEX Testing Equipment Systems Ltd.

    Our Air Permeability Tester determines the resistance of fabrics (woven, knitted and non-woven textile materials) to the passage of air (air flow) under constant pre-set air pressure while firmly clamped in the test rig of selected test head/area.The specimen is loaded to the test area of the instrument easily by means of a pneumatic holder. By pressing down the holder to start the test. The air permeability tester is equipped with a vacuum pump to draw air through an automatic interchangeable test head with a circular opening. The pre-selected test pressure is automatically maintained, and after a few seconds the air permeability of the test specimen is digitally displayed in the pre-selected unit of measure on the touch panel after test the holder is released and the vacuum pump is shut off.

  • Ultrasonic Hardness Tester

    Mitech Co., LTD.

    Non-destructive ultrasonic hardness tester, based on the principle of ultrasonic vibration sensor rod, can easily detect a variety of metal materials hardness without damage. Its measurement speed and precision is high and there will be no indentation. It uses advanced sensing system and single chip technology, better than the traditional ultrasonic hardness testers in structure and function. MU200 support value conversion among HRC,HB,HV and others and the multi-point measurement can be averaged. It can also accurately display and print the test results if possible. The product is widely used in hardness testing of finished workpiece, metal foil, metal thin layer (nitriding layer, carburizing layer, electroplating layer, etc.), difficult to move large parts, easy to dismantle the parts and special shape parts.It is one precision testing equipment to improve production pass rate and cost savings .

  • Universal Cable Tester

    PK-888 PANTESTER PRO - Pansco, Ltd

    PANTESTER PRO is an advanced pin to pin tester to identify wiring faults in voice, data network, video/security/media, PC-USB 2.0/3.0. Mini B, Firewire 1394 4/6/9 pins cables and any custom configuration assembly cables with no need for adapters. We’ve made PANTESTER PRO a more cost effective solution, providing an all inclusive device that is capable of a “quick check” test and learning mode for testing large quantity of custom cables and pin to pin mode for checking actual pin configuration of 1-10 pins cables. You can either step through the test cables wiring or have the tester automatically check and display the result on the main unit. Two sets of LED bars for source and test indication. Other features includes pass, fail and low battery indicators.

  • High Voltage Cable Tester

    E5 - Eastern Technology Corporation

    The Model E5 High Voltage Cable Tester tests Hi-Voltage aircraft engine ignition cables quickly and accurately. And it's incredibly easy to use: simply connect the three wires, push the test button and check the test window. That's all there is to it. By simulating the magneto's high output voltage, the E5 instantly identifies both good and defective cables. And it operates on either 12 or 24 volts,D.C.

  • High Voltage Testers

    GLP2 - Whitelegg Machines Ltd

    GLP2-tester series are the result of our experience in manufacturing following “customer based technology“ for more than 20 years. With precise, intelligent test processes the testers set the standard regarding operating ease, modularity, functionality, measurement accuracy and performance.AC tests up to 100 kV. DC tests up to 98 kV. Suitable for production testing of luminaries, white goods, coils etc.

  • Hipot Function Testers

    Compliance West USA, Inc

    Designed to provide a fast, safe and reliable way to verify proper operation of Dielectric Withstand (hipot) and Ground Continuity Testers between calibration cycles. It allows the operator to check the result of the three failure modes encountered in production hipot and ground circuit testing (open ground, high leakage current, and dielectric breakdown) separately or in any combination to verify proper test equipment operation