Showing results 2116 - 2130 of 5075 products found

  • HT2678 - Water-cooled Generator Insulation Tester

    Company: Wuhan Huatian Electric

    If you want to check insulation performance of electrical equipment, the quick and easy method is to measure insulation resistance. HT2678 Water-cooled Generator Insulation Tester, designed by our company, equipped with integrated circuits, is characterized by novel principle, simple operation, high precision, strong shock resistance, good work stability, large output short-circuit current. In the field environment, its strong anti-interference ability can meet the test requirements of power plants. With timing, alarm and data storage functions, the instrument can be easily used to measure insulation resistance, absorptance, polarization index and other parameters.

  • UCI-3000 - Ultrasonic Portable Hardness Tester

    Company: Qualitest International

    Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.

  • MME-UT 20 - Universal Tester with LCR meter

    Company: Minmax Electronics

    MME - UT 20 is the latest Microcontroller based Universal IC tester with LCR Meter from Minmax Electronics. It functionally tests 74 series of TTL ICs 40 & 45 series of CMOS ICs, Analog/Linear ICs op amps, comparators, timers, transistor arrays, ADC, DAC etc., It also tests components like diode, transistors, UJT, FET, SCR, Displays, Regulators (78/79) and DIP relays. It also measures the values of Inductance (L), Capacitance(C) and Resistance(R). MME-UT 20 has Rs232 Serial Interface through which IC test Library could be expanded.

  • MEMS Device-Oriented Testers

    Company: SPEA Italy S.p.A.

    Are your test requirements oriented to defined families of devices, with common characteristics? You do not need to purchase an expensive, general-purpose mixed signal tester: You can rely on SPEA DOT 100, a system designed to answer the test requirements of MEMS and other low-pin-count devices at an incredibly low cost.The DOT 100 is based on a revolutionary per-device architecture: each device under test has a dedicated CPU managing the entire test process, while each card hosts all the resources for the parallel test of 3 devices, in the size of a postcard.

  • DFQ40K - Fuel quantity tester

    Company: Barfield

    The DFQ40K is designed for and is compatible with all aircraft, which have AC capacitance, based Fuel Quantity Indicating Systems including those equipped with transient suppressors.The DFQ40K has the ability to measure the insulation breakdown of tank units, wiring and connectors associated with the system, capacitance of the tank units which measure the level of fuel in the tanks and simulation of capacitances required to test and calibrate the aircraft indicating system. In addition to performing the standard capacitance tests of the Tank(s) and or Compensator, the DFQ40K has an additional troubleshooting mode that will provide the user with a relative indication of a problem associated with the Phase of the return current like that provided by the Barfield 2548H tester.

  • EB 16II - Hot Set Tester

    Company: Qualitest International

    Hot Set Tester - EB 16II is made for hot set testing of cable material according to IEC 811-2-1. To avoid too high temperature loss when inserting and cutting the samples, the samples are introduced through a small opening in the top of the oven. To get a suitable working height and not shake the samples during insertion, the oven is fixed and the sample holder moves up and down by a servo motor driven screw system. The oven has a controlled air exchange rate and low air speed which can be controlled by a flow meter, meeting the requirements for ageing ovens in IEC 811.

  • RK2678XM - Ground Resistance Tester

    Company: Shenzhen Meiruike

    RK2678XM ground resistance tester is used to measure grounding resistance of electrical equipment inside, which reflects the entire electrical equipment exposed to lead (contact) resistance grounding terminal portion of the total electrical equipment between. According to GB , IEC , ISO , BS , UL , JIS and other international and domestic safety standards and design , to meet the clause of Part 1 , GB8898 , GB3883 , GB7251.1-2005 , GB5226.1-2002 other domestic and international safety standards test .Suitable for measuring the resistance of a variety of electrical, electronics, instrumentation, home appliances and other equipment shell grounding wire between its value.

  • BC2000 - Insulation Resistance Tester

    Company: Wuhan Huatian Electric

    BC2000 Insulation Resistance Tester (two gears) adopts embedded industrial single-chip Real Time Operating System, adopts extra-thin tensile-spring header perfect assembled with LCD . It with various output voltage (500V,1000V,2500V,5000V), high capacity, strong anti-interference ability, pointer display synchronously with data , applies to DC and AC, easy to operate, calculates the insulating index ( absorptance, polarization index), results automatically, without power failure, etc. It is the ideal equipment to test large-capacity transformer, mutual inductor, generator, HV electric motor, power capacitor, cable, lightning arrester and so on.

  • Non-Contact Resistance Online Tester

    Company: MEWOI Electronics

    Non-Contact Resistance Online Tester is our company devotes ourselves to Grounding resistance test technical research’s another new high-tech product for more than ten years. Detector adopts weather fastness material manufacture, temperature resistance, cold-resistant, corrosion prevention, fire prevention. Detector’s structure is rigorous and firm, against rain, dustproof, installation and use outdoors. Non-contact measurement, safe and reliable, Ease of installation. Grounding down lead is directly through the detector perforation, Will not affect lightning protection grounding effect and the normal operation of the facilities. Ensure high-accuracy, high stability and high reliability of long time on-line monitoring outdoors, underground mine and indoors.

  • ISL-4800 - Image Sensor Tester

    Company: Jova Solutions

    The Jova Solutions ISL-4800 is the highest performance interface and test solutions available for image sensors, digital cameras and video devices. This single piece of hardware supports nearly every sensor, camera, and video source interface standard in existence. A fully integrated, off-the-shelf, hardware/software tester package, ISL-4800 provides a full range of interfaces, controls, advanced image analysis test routines, evaluation and characterization capabilities in one easy-to-use, inexpensive, small-footprint solution. The ISL-4800 is a powerful, affordable, flexible, and expandable solution that supports future requirements with field upgradable FPGA code and a flexible interface board architecture

  • TH2882A-5 - Impulse Winding Tester

    Company: Tonghui Electronic

    Because of the influence of coil wire material, magnetic material, framework and process craft etc., coil product (such as transformer, motoretc.) can generate debasement of the insulation performance of the coil layer, circle and down-lead. TH2882AS-5 impulse winding tester, adopting high-speed sampling technique to develop, is a new analysis test instrument for insulation performance of coli product.Memorizing sampling waveform of standard coil winding in the instrument inside, when testing, TH2882AS-5 compares standard waveform and tested waveform according to criterion of settings (Area, Differential Area, Corona Discharge, Differential Phase etc. ),

  • MIT2500 - Insulation and Continuity Tester

    Company: Megger Group Ltd

    The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.

  • MultiTest-dV - Motorised Force Testers

    Company: Mecmesin Limited

    The MultiTest-dV range comprises three outstanding value, superior, motorised force testers. Designed for precision-controlled compression and tension testing, the dV’s simple controls, backed by sophisticated electronics, make it the ideal choice for a wide range of routine testing. Its multifunctional control wheel allows precise setting of speed and position, while its coloured LEDs clearly indicate machine status during testing. Test to a target displacement or limit, and using any one of the Mecmesin range of Advanced Force Gauges (AFG), to a load limit or break. For many applications, the MultiTest-dV provides a highly versatile and affordable solution, which will provide consistently reliable performance.

  • K-475DVP - Alternator, Generator and Starter Tester

    Company: KAR Industries

    The K-475DVP has been specially designed to test alternators, generators and starters for light cars to heavy duty trucks. This 7.5 HP Tester has 6 preset loads to test for maximum performance and an electronic variable speed control which allows testing at RPM levels of from 0 to 6000.  The use of digital meters increases accuracy and makes it easy for the operator to read.  During testing the newly added computer to the K-475DVP allows the operator to save the test results and to print them at the end of the trial. These results are easily identified by a computer-generated serial number given to each test.

  • DALT55 & DAS650 - Air Data/Pitot Static testers

    Company: Barfield

    The DALT55 Digital Altimeter and the DAS650 Digital Airspeed indicator were designed to be a direct replacement to the current analog instruments. Being of similar shape and size of existing analog instruments, the new digital version fits all Barfield 1811 series and most other manufacturers of analog pitot-static test sets. Standard analog instruments provided in a Barfield 1811 series or equivalent pitot-static tester are delicate mechanical devices easily damaged or destroyed by inexperienced or distracted technicians. The DALT55 and DAS650 use stateof- the-art transducer technology for pressure measurements making them virtually immune to the frequent and costly repairs generally associated with analog instruments.

Products

Applications

Manufacturers