Testers: find the limits of a design.

Showing results 421 - 435 of 4982 products found

  • sonic tester

    PR-82 - Dakota Ultrasonics

    The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.

  • Solderability Tester

    LBT210 - Microtronic GmbH

    Microtronic's LBT-210 solderability tester has software that offers statistical information such as mean value, standard deviation, etc. A camera option offers video of the test cycle and storage in memory with the appropriate test measurements and data. Additionally, it has the feature to test under nitrogen. This function can be switched on in the software. An enclosure that is flooded with nitrogen lowers and rises with the device under test.

  • WRISTAT TESTER

    WT25 - Walter G. LEGGE Co., Inc.

    The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).

  • Multiparameter Testers

    Hanna Instruments, Inc.

    The housing of this tester has been completely sealed against humidity and is designed to float. Electrode replacement with the stainless steel round connector means there are no pins to bend or break during replacement. When the cloth junction becomes clogged and response time is sluggish, simply pull out 3 mm (1/8") to clear the clogging which will improve response time and stability. The exposed stainless steel temperature sensor on these models facilitates faster and more accurate temperature measurement.

  • Rainproof Tester

    TF161 - TESTEX Testing Equipment Systems Ltd.

    Rainproof Tester, to determine the penetration resistance of fabrics or composites at different intensities of water impact. Simulated rain horizontally impacts fabric samples mounted vertically in a stainless steel bath. Samples are backed with a standardized blotting paper, which is weighed before and after each test. The rain is formed by a column of water, which can be adjusted from 600mm to 2400mm.

  • Diode Tester

    FEC CV400 - Frothingham Electronics Corporation

    The CV400 tests silicon Transient Voltage Suppressor (TVS) diodes, uni-polar and bipolar. The waveform used for the main test is the 10/1000µs waveform.The tester can also produce 8/20µs and 6/70µs exponential waveforms, 8.3ms half sine and rectangle pulses.These tests not only prove the ability of the DUT to endure the pulses without failure, but also measure the peak voltage across the device during the pulse.The CV400 can also measure the VZ of the device both before and after the pulse. Limits may be applied to the absolute value of these VZ tests and to the difference between them. If the initial VZ is outside the programmed limits, the part can be rejected and the main pulse not be applied.IR can be measured before and after the main pulse. This test is intended to detect damage due to the main pulse which is too slight to be detected by the main pulse or VZ test.The tester is designed to work with one or two automatic handlers or manual test stations. Bin sort outputs sort the parts into good devices that pass all requirements, several classes of rejects, and those parts which were not completely tested because of some fault condition.

  • Textile Tester

    USTER TESTER 6-C800 - Uster Technologies Ltd.

    The USTER TESTER 6-C800 is ready for the most demanding technical textiles applications. The amazing diversity of technical textiles applications is matched by the wide variety of quality characteristics needed in the raw material used so filament yarn producers know they must work to the most stringent specifications and standards. Quality failings, especially in the critical parameter of yarn evenness, can be expensive, but the USTER TESTER 6-C800 provides fast, accurate testing to the tightest tolerances, protecting filament producers against customer complaints and claims. Raw materials for technical textiles cover a wide range of end-uses and performance requirements. Viscose fibers, for instance, are found in lightweight blouses as well as in wire cording and high-speed car tires. Polyester, common in low-price clothing, is also transformed in special high-tech versions, for sophisticated sportswear and outdoor clothing. Countless other examples of technical applications for filament yarns span sectors such as medical, industrial, transport, engineering and protective clothing. Despite this variety of products, there is one fundamental requirement which is common to all: the absolute need for yarn evenness, measured to close tolerances, to ensure that the functional and aesthetic properties of the finished article achieve the high quality standards that customers demand.

  • Battery Tester

    BAT 110 - Bosch Diagnostics

    he BAT 110 is a rugged battery tester that uses state-of-the-art conductance technology to provide quick and accurate load-free testing of most types of 12V batteries, including AGM, standard, and maintenance-free batteries. In addition to conductance technology, the BAT 110 incorporates a temperature compensation feature to aid in battery tests results that are extremely accurate. Utilizing the test battery for power (no internal batteries to worry about), the BAT 110 can test batteries that are as low as 5.5 volts. As a voltmeter, the BAT 110 has a test range of 5.5V to 19.99V. The battery cold cranking amp test range is from 200 850 CCA.

  • Capacitor Tester

    CapAnalyzer 88A - Electronic Design Specialists

    The CapAnalyzer 88A checks electrolytic capacitors in-circuit for both ESR and DCR with no unsoldering. It is the only capacitor tester that discharges the cap, checks it for low DC Resistance (DCR), reads out high-frequency Equivalent Series Resistance (ESR) and compares your readings to industry standards on the three-color chart right on the front panel. The included one-handed tweezer probe allows testing of both normal and surface-mounted electrolytics and uses coaxial cable instead of normal test-probe wire for stable readings on small capacitors. Now shipping series II, which gets extended battery life.

  • ELT Testers

    BT200 Series - WS Technologies Inc.

    Building on the features of the industry standard BT100, the BT200 offers improved measurement capabilities and in a fully integrated and ruggedized device. The BT200 meets and exceeds the measurement requirements for EPIRBs (IMO MSC/Circ.1039 and 1040) and for ELTs in the USA (FAA Part 91.207), in Canada (CAR 571 Appendix G), and Europe (CAA/EuroCAE requirements).  These Beacon Testers in fact form a cost effective solution by eliminating the need for other costly test equipment.  Don’t risk incomplete testing of your beacons – use the BT200 to test them thoroughly.  In compliance with your Quality Assurance requirements, detailed calibration data is included with each Certificate of Calibration.

  • Ferroelectric Tester

    Premier II - Radiant Technologies, Inc.

    The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.

  • LAN Testers

    Aegis Pty. Ltd.

    Enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.

  • Hydrostatic Testers

    Hydraulic Technology, Inc.

    Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 25 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07.

  • Wetting Tester

    SP-2 - Malcom

    The Malcom SP-2 Wetting Tester helps to test the wettability of solder paste and components while actually simulating the SMT mounting and reflow process. The SP-2 simulates the actual temperature that solder paste undergoes during preheat and reflow, letting you easily identify any deficiencies in flux activity or components wettability. Measurement of the solder paste wettability, components wettability, printed board wettability, wettability on temperature rise, and wettability on preheating time. By actual simulation of the SMT mounting and reflow process with standard variable, it is possible to develope an accurate, repeatable evaluation method to determine a solder paste''''s solderability.

  • TLP Tester

    HED-T5000/ HED-T5000VF - Hanwa Electronic Ind. Co.,Ltd.

    Most advanced test mode for TLP testBoth of NTLP(normal TLP) and VFTLP(Very Fast TLP) type are offered to our customer.Pulse width of normal type TLP is 100ns/200ns, and is 1ns for VFTLP.These are useful to verify ESD withstand voltage in HBM/MM test mode.◆Powerful monitor to support analysisAn oscilloscope included in TLP tester allows to be confirmed an incident wave to device and a reflective wave from device.After the incident and reflective wave automatically saved, display on the exclusive monitor.The exclusive monitor displays the incident and reflective wave with total, in addition, snapback characteristics and leak measurement value from Vf/Im measurement with trace.

Products

Applications

Manufacturers