Showing results 436 - 450 of 5130 products found

  • 6000 Bird Dog Plus - CT Tester

    Company: Spinlab Utility Instrumentation

    This new and exciting true 3 phase Bird Dog Plus enables you to determine the accuracy of any meter in the field--from Form 1 through Form 17. Electronic sensors allow you to automate the test to gain the highest possible accuracy. The process is fast, simple, and much less expensive than a portable test board for the meter test and still perform ratio & burden tests on your CTs (CT Tester).

  • MPO Tester

    Company: Liverage

    The MPO Tester is a very useful tool designed for checking the defects of a MPO arrayed fiber cable or MPO Connector. The MPO emits a visible 650 nm wavelength visible red laser light through fiber optic cables, then if there are breaks or defects in the fiber will refract the light, creating a bright glow around the faulty area. The LD output signal can be all 12 Fibers switched to CW Mode to obtain different visual effects.

  • WFT-20 - Wi-Fi Tester

    Company: ShinewayTech

    WFT-20 is a PDA based Wi-Fi tester for scanning, analyzing and optimizing 2.4/5 GHz WLAN, which operates on IEEE802.11A/B/G/N standards and allows user to evaluate entire network and each channel’s status, detect and monitor AP with MAC address, SSID, data encryption and RSSI signal level information. WFT-20 also provides utility tools like Free Space Loss, AP Detector, Power Meter, Client Finder, Distance Calculation and mW/dBm Conversion.

  • WT25 - WRISTAT TESTER

    Company: Walter G. LEGGE Co

    The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).

  • FEC CV400 - Diode Tester

    Company: Frothingham Electronics

    The CV400 tests silicon Transient Voltage Suppressor (TVS) diodes, uni-polar and bipolar. The waveform used for the main test is the 10/1000µs waveform.The tester can also produce 8/20µs and 6/70µs exponential waveforms, 8.3ms half sine and rectangle pulses.These tests not only prove the ability of the DUT to endure the pulses without failure, but also measure the peak voltage across the device during the pulse.The CV400 can also measure the VZ of the device both before and after the pulse. Limits may be applied to the absolute value of these VZ tests and to the difference between them. If the initial VZ is outside the programmed limits, the part can be rejected and the main pulse not be applied.IR can be measured before and after the main pulse. This test is intended to detect damage due to the main pulse which is too slight to be detected by the main pulse or VZ test.The tester is designed to work with one or two automatic handlers or manual test stations. Bin sort outputs sort the parts into good devices that pass all requirements, several classes of rejects, and those parts which were not completely tested because of some fault condition.

  • ZC-221 - Tan-Delta Tester

    Company: Kvtester Electronics

    Product Features1. adopts converter technique to ensure accurately testing under strong electric field2. micro computer automatically finish the whole test.3. this device also applies to test the tgδ and capacitance of the HV tester of the workshop, laboratory and R&D institution.4. this device can test the grounded or non-grounded HV tester using forward method, it can also test the tgδ and capacitance C1, C2 of the main capacitor of the capacitor voltage transformer.5. built in H. V. step up transformer, and adopts the safety precautions of zero passage closing switch and lightning proof. During the test output voltage of 0.5KV~ 10kV, easy and safe to operate.Technical ParameterHigh voltage output: 0.5~10KVEach files to increase the 500V, a total of twenty files, capacity: 1500VAAccuracytgδ:±(reading*1.0%+0.04%)Cx: ± (reading*1.0%+1PF)Resolving powertg δ: 0.01% Cx:1pFMeasuring range0.1%< tg δ< 100%3PF10KV,Cx≤30000PF5KV, Cx≤60000PF Power supplyAC 220V±10% 50±1HzMeasurement methodPower frequency: 50HzPilot frequency: 45Hz/55Hz Automatic frequency conversionHarmonic adaptation≤ 3%Service condition-15℃-50℃ relative humidity<80%Outline dimension460(L)*345(W)*350(H)Weight35KG

  • USTER TESTER 6-C800 - Textile Tester

    Company: Uster Technologies

    The USTER® TESTER 6-C800 is ready for the most demanding technical textiles applications. The amazing diversity of technical textiles applications is matched by the wide variety of quality characteristics needed in the raw material used – so filament yarn producers know they must work to the most stringent specifications and standards. Quality failings, especially in the critical parameter of yarn evenness, can be expensive, but the USTER® TESTER 6-C800 provides fast, accurate testing to the tightest tolerances, protecting filament producers against customer complaints and claims. Raw materials for technical textiles cover a wide range of end-uses and performance requirements. Viscose fibers, for instance, are found in lightweight blouses as well as in wire cording and high-speed car tires. Polyester, common in low-price clothing, is also transformed in special high-tech versions, for sophisticated sportswear and outdoor clothing. Countless other examples of technical applications for filament yarns span sectors such as medical, industrial, transport, engineering and protective clothing. Despite this variety of products, there is one fundamental requirement which is common to all: the absolute need for yarn evenness, measured to close tolerances, to ensure that the functional and aesthetic properties of the finished article achieve the high quality standards that customers demand.

  • Premier II - Ferroelectric Tester

    Company: Radiant Technologies

    The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.

  • BAT 110 - Battery Tester

    Company: Bosch Diagnostics

    he BAT 110 is a rugged battery tester that uses state-of-the-art conductance technology to provide quick and accurate load-free testing of most types of 12V batteries, including AGM, standard, and maintenance-free batteries. In addition to conductance technology, the BAT 110 incorporates a temperature compensation feature to aid in battery tests results that are extremely accurate. Utilizing the test battery for power (no internal batteries to worry about), the BAT 110 can test batteries that are as low as 5.5 volts. As a voltmeter, the BAT 110 has a test range of 5.5V to 19.99V. The battery cold cranking amp test range is from 200 850 CCA.

  • CapAnalyzer 88A - Capacitor Tester

    Company: Electronic Design

    The CapAnalyzer 88A checks electrolytic capacitors in-circuit for both ESR and DCR with no unsoldering. It is the only capacitor tester that discharges the cap, checks it for low DC Resistance (DCR), reads out high-frequency Equivalent Series Resistance (ESR) and compares your readings to industry standards on the three-color chart right on the front panel. The included one-handed tweezer probe allows testing of both normal and surface-mounted electrolytics and uses coaxial cable instead of normal test-probe wire for stable readings on small capacitors. Now shipping series II, which gets extended battery life.

  • HED-T5000/ HED-T5000VF - TLP Tester

    Company: Hanwa Electronic

    Most advanced test mode for TLP testBoth of NTLP(normal TLP) and VFTLP(Very Fast TLP) type are offered to our customer.Pulse width of normal type TLP is 100ns/200ns, and is 1ns for VFTLP.These are useful to verify ESD withstand voltage in HBM/MM test mode.◆Powerful monitor to support analysisAn oscilloscope included in TLP tester allows to be confirmed an incident wave to device and a reflective wave from device.After the incident and reflective wave automatically saved, display on the exclusive monitor.The exclusive monitor displays the incident and reflective wave with total, in addition, snapback characteristics and leak measurement value from Vf/Im measurement with trace.

  • Outlet Testers

    Company: Gardner Bender

    Circuit Analyzer makes it easy to test GFCI receptacles and determine the appropriate wiring correction needed. This GFCI tester uses advanced circuitry and a patent-pending proprietary design to precisely detect the required low resistance (less than 10ohms) on ground wire and provides a clear and easy-to understand single LED readout indication for Correct wiring or Bad Ground, Open Neutral, HOT/GND Reverse, HOT/NEU Reverse and Open Hot wiring errors without the need to memorize or decipher a dual-indication chart. The Stop Shock II includes a GFCI test function to test outlets wired in parallel to GFCI circuits (bathroom, kitchen and outdoor receptacles require GFCI protection).

  • 19052/19053/19054 - Hipot Tester

    Company: Chroma ATE

    The Chroma Hipot Tester 19050 series provide 3 models for choice. The 19052 for AC/DC/IR Hipot testing and insulation resistance (IR) measurements, the 19053 which combines both AC and DC Hipot tests and IR measurements with 8HV scan channel capability into a single compact unit, and the 19054 which combines both AC and DC Hipot tests and IR measurements with 4HV scan channel capability into a single compact unit. The front panels of the fevers make them easy to operate. Digital display and user friendly control allows test parameters and limits to be set easily without the high voltage activating.

  • Hydrostatic Testers

    Company: Hydraulic Technology

    Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 25 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07.

  • SP-2 - Wetting Tester

    Company: Malcom

    The Malcom SP-2 Wetting Tester helps to test the wettability of solder paste and components while actually simulating the SMT mounting and reflow process. The SP-2 simulates the actual temperature that solder paste undergoes during preheat and reflow, letting you easily identify any deficiencies in flux activity or components wettability. Measurement of the solder paste wettability, components wettability, printed board wettability, wettability on temperature rise, and wettability on preheating time. By actual simulation of the SMT mounting and reflow process with standard variable, it is possible to develope an accurate, repeatable evaluation method to determine a solder paste''''s solderability.

Products

Applications

Manufacturers