Showing results 4876 - 4890 of 4934 products found

  • HTZZ-2A - inding Resistance Ohmmeter

    Company: Wuhan Huatian Electric

    inding Resistance Ohmmeter is an essential test project during transformer transfer, repair and changing tapping switch. Measuring DC resistance of transformer winding, you can check out weld or connection quality of down-lead, the winding inter-turn short circuit or open circuit, and whether tap-changer is well contacted. In the previous it is generally to use QJ44 double bridge to measure DC resistance, but the measuring current for this type of bridge is mA level current. So measurement will take a long time, and accuracy is lower. In order to change the above situation, our company has developed HTZZ-2A DC Resistance Rapid Tester.

  • H730035xx - High Voltage Switching matrix

    Company: 6TL Engineering

    This switching matrix enables the switching between different test poinits, when performing dielectric strenght test and Hipot test. It is featuring High Voltage relays, controlled through CAN bus. The module features one relays normally closed, with a red LED that is indicating its status, that when no power, will keep J2 and J3 input terminals linked through a resistor, to ensure electric discharge of all loads after the test. Conexions are made with special high voltage conectors. Input terminals from Hipot tester are in front of the module, while up to 8 outputs are in the back panel. A 4 wire connector in the back plane, is used for powering up the device and control through CAN bus.

  • Insulation Test Generator

    Company: EMC Partner AG

    Screw connections on top of the generator, enable easy connection to the EUT. The MIG0603 is the ideal voltage insulation tester with a broad application range. The MIG "Modular-Impulse-Generator" is a flexible kit system, ready to quote tailored generators for special test applications. The MIG is a further innovative solution of EMC PARTNER AG to cover customers requests. The basic units are discharge modules (patent pending) which can be configured in serial or parallel, to offer an optimum solution for the customer need. The use of one type of discharge module guarantees a high reliability and a high qualit . Requires TC-MIG24 or CN-MIG24.

  • MD 5075x - Insulation Resistance Measurement

    Company: Scope T&M Pvt Ltd

    The digital insulation tester model MD-5075x is Megabras'' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TW, with 4 pre-selected test voltages, 500 V - 1 kV - 2.5 kV - 5 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.

  • DSX CableAnalyzer™ Series - Copper Test Solution

    Company: Fluke Networks

    he DSX CableAnalyzer Series copper test solution enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you’ll be. Unfortunately, there are a lot of things that slow the process down – setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand.

  • MOIST-41 - Moisture analyzer

    Company: MRC Ltd

    Max Sample 18 samples (Inherent moisture)9 samples (total mo moisture)Sample Weight (0.9-1.1)g for moisture content on airdried basis; (10-12)g for total moistureFurnace Temperature 105C t0 110CTemp. Control Precision 3CAnalysis Time (20-40)minPower Requirement 220V(-15%-10%), 50HzMax Power 1.5kwSize / Net weight 542x506x564mm / 53kgStandard Layout Moisture Tester / Lenovo PC(Desktop) / PrinterISO117722 Solid mineral fuels Hard coal Determination ofmoisture in the general analysis test sample by drying innitrogen ASTM D5142-09 Standard Test Method forProximate Analysis of the Analysis Sample of CoalGB/T212-2008 Standard

  • HTZZ-3A - Winding Resistance Ohmmeter

    Company: Wuhan Huatian Electric

    Winding Resistance Ohmmeter is an essential test project during transformer transfer, repair and changing tapping switch. Measuring DC resistance of transformer winding, you can check out weld or connection quality of down-lead, the winding inter-turn short circuit or open circuit, and whether tap-changer is well contacted. In the previous it is generally to use QJ44 double bridge to measure DC resistance, but the measuring current for this type of bridge is mA level current. So measurement will take a long time, and accuracy is lower. In order to change the above situation, our company has developed HTZZ-3A DC Resistance Rapid Tester.

  • #8029 - 7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit

    Company: Innovative Products

    Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner

  • SS7 - Protocol Simulator using MAPS

    Company: GL Communications

    GL's MAPS™-SS7 is an advanced protocol simulator/tester for SS7 simulation over TDM (E1/T1).MAPS™ can simulate Service Switching Point (SSP) and ISUP signaling specification as defined by the ITU-T standards. The tester supports testing network elements, error tracking, regression testing, conformance testing, load testing/call generation and generation of high volumes of ISUP traffic. MAPS™-SS7 functionality covers the ITU and ANSI variant of SS7 implementing MTP2, MTP3, and ISUP protocols. It is able to run pre-defined test scenarios against ISUP test objects in a controlled & deterministic manner.

  • Inspection System

    Company: Chroma ATE

    Integrated with 2D Geometry, Surface, Micro Crack, Saw mark inspection system and Resistively & Thickness, Lifetime tester by customer defined, Chroma 3710HS is a fully user configuration wafer sorter system with very low breakage rate and high through put. Chroma 3710HS solar wafer inspection system is ideal for PV incoming process. Plus wafer can be sorted by user defined algorithm fully automatically into coin stack or cassette. The unique auto coin stack/cassette exchange feature eliminates system down time when changing full coin stack/cassette to empty coin stack/cassette manually.

  • mOByDic1610 - CANBUS OBD ECU Simlator

    Company: Ozen Elektronik

    The CAN BUS multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates 4 differnt ECUs. reading VIN and suspended DTC is possible . Using 5 potensiometer , 5 live data can be changed and some fixed PID values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. Service 4 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 12 V power supply . More information you can get from the corresponding chipset datasheet.

  • mOByDic1700 - OBD ECU Simlator

    Company: Ozen Elektronik

    The J1939 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates a Truck ECU . Using 5 potensiometer , 5 live data can be changed and some fixed PNG values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. DM11 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 24 V power supply . More information you can get from the corresponding chipset datasheet.

  • mOByDic1310 - VPWM OBD ECU Simlator

    Company: Ozen Elektronik

    The J1850 VPWM multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates 4 differnt ECUs. reading VIN and suspended DTC is possible . Using 5 potensiometer , 5 live data can be changed and some fixed PID values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. Service 4 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 12 V power supply . More information you can get from the corresponding chipset datasheet.

  • mOByDic1010 - OBD ECU Simlatr

    Company: Ozen Elektronik

    The ISO 9141 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates 4 differnt ECUs. reading VIN and suspended DTC is possible . Using 5 potensiometer , 5 live data can be changed and some fixed PID values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. Service 4 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 12 V power supply . More information you can get from the corresponding chipset datasheet.

  • MTS-207 - Rugged Field Test Set

    Company: Marvin Test Solutions

    The MTS-207 is a state-of-the-art portable PXI platform for field testing and data acquisition systems. Its proven architecture has been deployed worldwide on multiple programs including the MTS-206 Maverick Missile system flight line tester, the MTS-209 Common Armament Test Set, the AN/TSM-205B Hellfire System test Set, and many more. It combines the capabilities of the versatile and powerful PXI architecture in a compact, ultra-rugged, flight-line qualified enclosure. The MTS-207 is ideal for test and data acquisition applications requiring operation under harsh environmental conditions including flight-line, back-shop, or airborne applications.

Products

Applications

Manufacturers