Showing results 4951 - 4965 of 5044 products found

  • MAPS-ISDN - Protocol Emulator

    Company: GL Communications

    GL's MAPS- ISDN is an advanced protocol simulator/tester for ISDN simulation over TDM (T1/E1) and generates high volumes of ISDN traffic. The tester can simulate ISDN signaling as defined by the ITU-T standards. Currently this test tool is used to perform testing using ISDN protocol messages over T1/E1, and offers a complete solution for testing, troubleshooting, and maintenance of devices and networks implementing PRI ISDN. It is useful to test ISDN products designed for either U or S/T interface, including network terminations, Type 1 terminating equipment, and terminal adapters.

  • GSM Abis - Interface Emulator using MAPS

    Company: GL Communications

    GL's GSM Abis Interface Emulator is an advanced protocol simulator/tester for GSM simulation over Abis Interface that can simulate BTSM messages and signaling specification as defined by 3GPP standards. The tester supports testing network elements BTS and BSC, Error tracking, regression testing, conformance testing, load testing/call generation and generation of high volumes of GSM traffic. It is able to run pre-defined test scenarios against GSM Abis interface test objects in a controlled & deterministic manner.

  • SIGTRAN (SS7 over IP) - Emulator using MAPS

    Company: GL Communications

    MAPS™-SIGTRAN is an advanced protocol simulator/tester for SS7 simulation over IP Networks. It can simulate a Signaling Gateway and Softswitch ISUP signaling specification as defined by ITU-T standards. The tester supports testing network elements, error tracking, regression testing, conformance testing, load testing/call generation and generation of high volumes of ISUP traffic. MAPS™-SIGTRAN functionality covers the ITU and ANSI variant of SS7 implementing M3UA, and ISUP protocols. It is able to run pre-defined test scenarios against ISUP test objects in a controlled & deterministic manner.

  • GSM A - Interface Emulator using MAPS

    Company: GL Communications

    GL's GSM A Interface Emulator is an advanced protocol simulator/tester for GSM simulation over A Interface that can simulate BSSMAP and DTAP messages and signaling specification as defined by 3GPP standards. The tester supports testing network elements MSC and BSC, Error tracking, regression testing, conformance testing, load testing/call generation and generation of high volumes of GSM traffic. It is able to run pre-defined test scenarios against GSM A interface test objects in a controlled & deterministic manner.

  • Dimensional Calibration

    Company: Alliance Calibration

    123 BLOCKS ANGLE BLOCKS BALL BAR BORE GAGE CALIPERS CHAMFER GAGES CMM'S COATING THICKNESS GAGES CYLINDER PLUGS DEPTH GAGES GAGE BLOCKS GO-NO-GO GAGES HARDNESS TESTERS HEIGHT GAGES INDICATORS LENGTH STANDARDS LEVELS MICROMETERS OPTICAL COMPARATORS PARALLELS PIN GAGES PROFILOMETERS RADIUS GAGES ROUGHNESS SPLINES THREAD RINGS THREAD PLUGS

  • UDP Test Suite

    Company: InterWorking Labs

    The UDP Test Suite is used by design engineers, quality assurance engineers and testers to find and fix bugs in their UDP implementation. The tests help ensure that the UDP implementation is sufficiently robust so that it is not vulnerable to the wide range of attacks in today's Internet. The tests make use of the Maxwell Pro network emulation environment, so that each test sequence can intelligently impair all aspects of the UDP protocol.

  • TCP Tests

    Company: InterWorking Labs

    The Maxwell Pro TCP Test Suite is used by design engineers, quality assurance engineers and testers to find and fix bugs in their TCP stack or engine. The tests help ensure that the TCP stack is sufficiently robust so that it is not vulnerable to the wide range of attacks in today's Internet. The tests make use of the Maxwell Pro network emulation environment, so that each test sequence can intelligently impair all aspects of the TCP protocol.

  • Ranorex Studio - Automated Testing of Desktop. Web. Mobile

    Company: Ranorex GmbH

    Create, maintain and run automated tests. Find bugs more quickly and make testing more reliable. Automate tests - start functional test automation in teams that include both testers and developers. A GUI test automation framework for testing desktop, web & mobile apps (incl. HTML5, WinForms, WPF, Flash/Flex, SAP, .NET, Java, iOS, Android, Windows Apps).

  • RF Analyzers

    Company: Bird Technologies

    Birds' line of Handheld RF Analyzers are rugged solutions for your field analysis needs. Ranging from the multi-functional SignalHawk Series and Spectrum Analyzers, to the SA Series, 25-6000 MHz Site Analyzers - a user-friendly test solution for installing, maintaining, and troubleshooting your antenna and cable systems, to the AT Series, Antenna Testers which provide a cost-effective, fast, graphical way of determining the quality of mobile and base station antennas.

  • Post Silicon Validation Solutions

    Company: Test Evolution

    Post-silicon validation (PSV) of first silicon tends to be an ad hoc process, stitching together protocol testers from various manufacturers to create test cases and debug issues. While IC’s are getting to market, the process is far from ideal. Leveraging the tools and methodology of pre-silicon verification into post-silicon validation is a key enabler to higher productivity. Test IP-based PSV is a paradigm shift from the way post-silicon validation is currently done. Individual protocol testers, scopes, miscellaneous equipment from various vendors, and on-chip logic are cobbled together in an attempt to create meaningful stimulus, response checking, and debugging.The problems with these ad hoc solutions:Protocol boxes from multiple vendors generally do not work together well. Each has its own driver software, programming model and debugging tools.Tool flows from pre-silicon to post-silicon to production and back are nonexistent. This makes writing tests challenging and thus generally limited in robustness. Also, debugging suspected problems is difficult across more than one interface.

  • Ultra Low Cost PCBA First Article Verification System

    Company: Zero Defects International

    Zero Defects International [ZDI] has announced the introduction of a pilot-run fault detection tester. This test verification system, when utilized on first article printed circuit board assemblies [PCBAs], will find component mounting faults. This will result in smoother and faster subsequent higher volume set-ups. Locating first article faults contributes to overall productivity improvement in the manufacturing line because potential component mounting problems will have been precluded.This test system is available in both manual and in-line configurations and each model is available with two different inspection areas. Features include: offline programming, easy to use software and very swift programming by operators of the equipment. A major benefit associated with the tester is the pricing which is begins at approximately $20,000 for the manual model. Additionally, all models are available for immediate delivery in the ZDI sales coverage region which includes the Northwest USA.Zero Defects International is a manufacturer’s representative organization and also provides PCBA flying-probe test services in Silicon Valley and beyond. The equipment represented by ZDI is primarily for PCBA test and inspection.

  • Revetest Scratch Tester (RST³) - Macro Scratch Testing Instrument

    Company: Anton Paar GmbH

    Based on Anton Paar’s unmatched experience in scratch testing, the Revetest® Scratch Tester RST³ has been developed for evaluating hard coatings with a typical coating thickness of several microns. The RST³ is capable of applying forces in the range 0.5 to 200 N to test the adhesion, cohesion and structural integrity of modern coatings. Such coatings may be organic, inorganic, used for magnetic and decorative applications, including CVD, PECVD, PVD, metallization and passivation layers, or friction and wear protective coatings. The substrates used can be refractive and organic materials, minerals, glasses, semiconductors, alloys and metals. Developed with all-new onboard electronics, the RST³ is more compact and more suited to Quality Control (QC) laboratory environments. The simultaneous release of the latest software (V7.3) allows the user to automatically detect the critical load based on a threshold on all the optional sensors (penetration depth, acoustic emission or friction force). This feature makes the Anton Paar RST3 the first scratch tester with automatic detection of critical loads.

  • SAT-JD200 - DC Ground Fault Locator

    Company: Shaanxi Aitelong

    SAT-JD200 DC Ground Fault Locator is applicable for any voltage in DC system, provided high accuracy clamp, to process multiple signals efficiently and increase detecting range and anti-interference capacity, to display the insulation level of the tested circuit branch in the forms of insulation index and wave, to indicate the relative ground point direction of the testing point. The users can customize an equipment with a proper insulation alarm threshold value within the insulation alarm threshold value limit according to requirement, only need to correspond the clamp meter gear with the measuring range on the tester so as to accomplish the direct ground testing or insulation level analysis.

  • 201 Series - Discrete Semiconductor Test System

    Company: SemiTek International

    The SemiTek 201.net Discrete Semiconductor Test System is PC-based using a CPU-based hardware controller to control the electrical tests it performs. In its sixth generation, the 201.net has served the semiconductor test industry for over twenty-five years in manufacturing and inspection. As a general-purpose tester, the 201.net is ideal for inspection and production applications where precision measurements and versatility are required. Under program control, the 201.net tests a growing number of devices including: * Diodes / Zeners * Bipolar Transistors * Field Effect Transistors * Arrays * MOSFET * MOSFET Depletion * Optocouplers * JFet / JFet NO * Mechanical Relays * Sidac * Triac / SCRs * IGBT

  • LCII - Ferroelectric Test System

    Company: Radiant Technologies

    Precision LC II is an affordable Ferroelectric Tester for research labs. This system offers 5Khz at 9.9V and also comes in a built in 10V, 30V, 100V, and 200V option. This unit can also be expanded to 10kV for bulk ceramic testing. Vision Software is provided with the LCII Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choose from.

Products

Applications

Manufacturers