Showing results 5071 - 5085 of 5130 products found

  • Ohm-Stat Digital Display Megohmmeter

    Company: Static Solutions

    Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester

  • Oil-Tester, PH Meter & Water Quality

    Company: PeakTech Prüf- Und

    To measure the conductivity value (ranging from 0 - 2000 µS) which can therefore judge whether water is pure or not. The conductivity value will become lower if there is much less impurities existed in water (for example, distilled water that its purity is higher than others will get a lower conductivity value of approx. < 10 µS). In industrial sectors, it would be a great help for the quality of the products if using the good water (more pure water) in the process. It may cause several diseases if home drink water existing high conductivity & contain impurities, the (pure water tester) are designed to check the purity of water (water conductivity) also can determine the conduction of the “water filter” easily and rapidly.

  • MD 5075x - Insulation Resistance Measurement

    Company: Scope T&M Pvt Ltd

    The digital insulation tester model MD-5075x is Megabras'' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TW, with 4 pre-selected test voltages, 500 V - 1 kV - 2.5 kV - 5 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.

  • MOIST-41 - Moisture analyzer

    Company: MRC Ltd

    Max Sample 18 samples (Inherent moisture)9 samples (total mo moisture)Sample Weight (0.9-1.1)g for moisture content on airdried basis; (10-12)g for total moistureFurnace Temperature 105C t0 110CTemp. Control Precision 3CAnalysis Time (20-40)minPower Requirement 220V(-15%-10%), 50HzMax Power 1.5kwSize / Net weight 542x506x564mm / 53kgStandard Layout Moisture Tester / Lenovo PC(Desktop) / PrinterISO117722 Solid mineral fuels Hard coal Determination ofmoisture in the general analysis test sample by drying innitrogen ASTM D5142-09 Standard Test Method forProximate Analysis of the Analysis Sample of CoalGB/T212-2008 Standard

  • AKT® - Electron Beam Array Test

    Company: Applied Materials

    The AKT Electron Beam Array Test (EBT) system provides dynamic pixel and TFT characterization and functional tests of flat panel matrix in mass production. With minimal mechanical motion and field proven AKT PECVD systems technology, the AKT EBT TFT array tester realizes high-throughput, high-reliability, low scheduled down time and low running cost. The AKT-15K EBT, AKT-25K EBT and AKT-40K EBT feature fast, large area beam positioning, multi e-beams testing in parallel, high-throughput yields especially with larger size TFT-LCD displays for flat panel television.

  • TB-1200-2 - Alternator Starter Test Bench

    Company: DURST Motor & Electric

    1200 Series Alternator Starter Test Bench: Features a specially designed 4Kw variable speed Durst motor, 5000-0-5000 RPM. Fitted with large easy to read analogue gauges: 3-0-3 Amp Diode tester, 10-0-10 Field Amp meter, 0-40Volt Electronic Regulator meter for 6, 12 & 24 volt units, 10-20-50Volt meter, 50-150-500-1500Amp meter and 6000-0-6000 Tacho meter, 500Amp carbon pile, multi-groove drive pulley, quick clamping alternator brackets, top & side loading starter clamps, slide feed screw for easy belt tensioning. Battery isolation switch

  • HD CCTV BOSS Series - 3.5” Installation & Test Meter for TVI, CVI, AHD & Analog

    Company: SecurityTronix

    The SecurityTronix ST-HDoC is designed for maintenance and installation of HD-CVI, HD-TVI, AHD and analog cameras as well as other security equipment. It’s 3.5” 480 x 320 resolution screen enables it to display images from HD cameras and analog cameras in top quality. The unit supports HD over coax, PTZ, ONVIF PTZ and analog PTZ controls. In addition, the tester is also a great tool for Ethernet networks and cabling systems. It includes the ability to test network cables while verifying the sequence of the individual conductors. The meters portability, user-friendly design and multi-function capability make it an essential tool for installers and technicians, greatly improving work efficiency and simplifying installations and system maintenance.

  • Probe Testing Services

    Company: Hughes Circuits

    We offer assembly testing services which are specially focused on reducing engineering debug efforts on small and medium production runs.Maintaining high product quality while keeping production costs low, together with aggressive schedules and time to market pressures, force manufacturers to choose lean yet effective test and quality assurance strategies for their production processes.Flying probe testers require no test fixtures, have few restrictions on board access, and can test boards with virtually unlimited number of nets, allowing developers to turn test programs around in a short time.

  • TNS-L Series - Spring Torsion Testing Machine

    Company: TIME GROUP

    TNS-S series testing machine is mainly used for testing the torsion angle and torque of various torsion springs, coil springs, elastic components and other friction structures.The tester consists of torsion transducer, photoelectric encoder, measurement amplifying circuit and single chip processor. The torsion angle and torque are digitally displayed.It can pre-set the upper and lower limits of torques for 4 points and automatically check whether the four test points are qualified. Automatically revise the angle displacement of torsion transducer.Functions of peak value holding, overload protection, torque stiffness calculation and data retrieval,

  • Spring Tension-Compression Machine

    Company: TIME GROUP

    The load measurement of this tester is digitally displayed, which avoids the reading error of human eyes. The displacement measurement is indicated by staff gauge and vernier, which gets rid of the displacement caused by the deformation of load cell, and therefore the measured displacement is more accurate. The machine is easy to operate,with high efficiency, high precision and stable performance, etc.Load display mode: Digital display, with indication function at upper & lower Limit.Displacement display mode: Staff gauge & vernier indication, with micro adjusting Function.Loading mode: Manual loading, quick and convenient, displacement control through positioning devices. (Above 5000N, automatically loading).

  • Static Analyzers

    Company: Accord Software &

    The goal is to enforce uniform coding habits among software personnel in the engineering department so that reading, checking and maintaining code written by different people becomes easier. CodeTrax can also be used to identify subtle programming errors. Software developers, testers, reviewers as well as quality personnel can use CodeTrax to ensure compliance with coding standards. The tool automates the code review process and reduces the effort and resources required. CodeTrax allows the user to benchmark the code developed in C against user defined coding standards. This product can be used any time during the project life cycle. However the best use of this product is from the start of the coding phase and while performing static analysis.

  • SM7110 and SM7120 - Super Megohm Meters

    Company: HIOKI E.E.

    Both products are designed for use in evaluating and testing the performance of electronic components used in products such as smartphones and hybrid vehicles. To accommodate vehicle components with increasingly high breakdown voltages, the SM7120 is the first insulation tester in the world to be able to output a measurement voltage of 2000 V (the SM7110 supports measurement voltage output of up to 1000 V). In addition, both products can complete testing twice as quickly as the previous Hioki model while offering dramatically improved measurement reproducibility and noise resistance. As a result, the new instruments promise to significantly improve evaluation and testing productivity.

  • Tensile, Compression and Bending Systems

    Company: MTI Instruments

    These miniature bend, fatigue, strain, and tensile testers are designed for use in Scanning Electron Microscopes (SEMs), and Light Microscopes (LMs). The dual leadscrew design symmetrically loads samples while keeping them centered within the scopes field of view. 100, 1000 and 2000 pound versions are standard with a wide range of sample clamps, bending fixtures (3 and 4 point) and compression anvils. Custom mounting adapters are available for integration into virtually all major microscopy tools. Optional heaters also offered for testing under high temperature conditions.

  • 3710-HS - Solar Wafer Inspection System

    Company: Chroma ATE

    Integrated with 2D Geometry, Surface, Micro Crack, Saw mark inspection system and Resistively & Thickness, Lifetime tester by customer defined, Chroma 3710HS is a fully user configuration wafer sorter system with very low breakage rate and high through put. Chroma 3710HS solar wafer inspection system is ideal for PV incoming process. Plus wafer can be sorted by user defined algorithm fully automatically into coin stack or cassette. The unique auto coin stack/cassette exchange feature eliminates system down time when changing full coin stack/cassette to empty coin stack/cassette manually.

  • Testif-i Land - Test Analysis for Land Seismic Systems

    Company: Verif-i Ltd

    Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.

Products

Applications

Manufacturers