Testers: find the limits of a design.

Showing results 1381 - 1395 of 4898 products found

  • Loudspeaker Cable Testers

    EMO E450 - EMO Systems Canford Audio PLC

    The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.

  • Ignition Spark Tester

    50850 - Lisle Corp.

    Quickly Checks Spark at Plug Wire. A handy tool to check ignition spark without removing the spark plug. The tool is specially calibrated to measure ignition voltage. Works on both standard and electronic ignition systems. Easy to use. Simply adjust calibration screw to proper gap size. Attach spark plug wire to end of tester. Clamp tester on engine to ground. Crank engine and check for spark.

  • Multi-Operational Surge Tester

    MB Model - PJ Electronics, Inc.

    Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.

  • Motorcycle Battery Testers

    ELAK Private Ltd.

    ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.

  • Micro Vickers Hardness Tester

    900-392 - Phase II Plus

    The 900-392 Micro Vickers Hardness Tester is engineered to produce a clearer indentation and hence a more precise measurement. By means of a 10 × lens and a 40 × lens the 900-392 vickers hardness tester has a wide measurement field and a broad usage range. Equipped with a digital microscope, it shows the measuring methods, the test force, the indentation length, the hardness value, the dwell time of the test force as well as the number of the measurements, all shown on its LCD screen.

  • Hipot/Ground Bond Tester

    ClareHAL Series - Seaward Group USA

    The ClareHAL hipot / ground bond tester will help you meet your testing and legal obligations, including data capture/logging/archiving. All basic tests, as specified in widely used product and safety standards, are included:Earth/Ground Bond testingDC Insulation TestingAC/DC Flash/Hipot/Dielectric withstand testingFunctional/ Run testingLeakage Current testingThe ClareHAL Tester can be used in three modes automatic, manual and direct PC control via the external communications port.

  • Hipot Testers (AC / DC)

    Haefely Hipotronics

    Our Hipot Testers (AC / DC) are accurate bench top AC and DC test instruments designed to perform insulation tests on all types of electrical system components, assemblies and apparatus. These hipot testers are simple to operate and designed for use by unskilled or semi-skilled personnel in production testing for ac dielectric and dc dielectric tests but only the H306B has the insulation resistance measurement with direct Megohmmeter readings at 500V dc output.

  • Insulation Testers for Telecoms Engineers

    Megger Group Ltd.

    With over twenty 1-kV models to choose from, selecting the proper Megger insulation tester can appear a bewildering task at first. Actually all the process requires is a little organization. All Megger insulation testers perform essentially the same test in fundamentally the same manner - accurately and reliably. Refinements and added features, however, separate one model from another in application and operator appeal.

  • Insulating Oil Tester

    IIJ-II - Chongqing Nakin Electromechanical Co., Ltd

    In the electric power industry, insulating oil is wildly applied in electric equipments. The dielectric strength is a comprehensive index for insulating oil. Series IIJ-II oil tester is special for testing insulating oil’s dielectric strength. IIJ-II Automatic oil tester is designed according to international standard of IEC156. Adopt industrial single chip as controller, apply large integrate circuit, new type I/O interface, LCD displayer, combined with special testing and anti-jamming technologies which greatly improve the tester's performance.

  • Ground Resistance Testers

    AEMC Instruments

    Whether you are doing a simplified 2-Point, a more complete 3- or 4-Point Fall-of-Potential test, a soil resistivity test or a touch potential test, AEMC has the right instrument for you. Our revolutionary clamp-on ground resistance tester will save you both time and money. Whichever AEMC ground tester you choose, you can count on it to be the highest quality, the most complete package and the simplest to learn to use.

  • Gear Teeth Hardness Tester

    PHT-1740 - Phase II Plus

    This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1740 is an economically priced hardness tester that is loaded with the same features found on the base 1700 version. The 1740 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.

  • Peel Force Tester

    PT-55 - V-Tek, Inc.

    V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.

  • Pencil Hardness Tester

    501 - Elcometer Limited

    The Elcometer 501 Pencil Hardness Tester has been designed to ensure that the cylindrical pencil lead is maintained at a constant angle of 45° and exerts a force of 7.5N (1.68lbF).The pencil lead, prepared beforehand using the special sharpener and abrasive paper, is inserted into the Elcometer 501 hardness tester and pushed over the smooth, flat coated surface.The lowest hardness value of the pencil which marks the coating determines the coating’s hardness rating.

  • Pendulum Impact Testers

    NI Series - NCS Testing Technology Co., Ltd.

    NI Series Pendulum Impact Testers are used to detect the impact resistance of metal materials under dynamic loads. It can conduct large quantities of metal impact tests continuously, display the impact absorbing energy and pre-elevation rotation angle of the pendulum and print test reports. It is useful not only for manufacturers of metal materials and quality inspection organizations, but also for research institutes for analsysi of new materials. It can use automatic sampling system to greatly improve the test efficiency and reduce the labor intensity of testers.

  • USB Tester 2.0

    TLS-0050 - FriedCircuits

    The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.

Products

Applications

Manufacturers