Showing results 1426 - 1440 of 5094 products found

  • S-GW Functional Tester

    Company: Polaris Networks

    The LTE SGW Functional Tester provides a wrap-around test solution for the Serving Gateway by emulating all the LTE network elements surrounding the SGW (System Under Test). The S-GW Functional Tester emulates an LTE eNodeB and other Core Network entities such as the MME, P-GW, S-GW, RNC and SGSN. It tests the S1-u, S11, S5/S8 , S12 and S4 interfaces of the S-GW.

  • Shoe Dielectric Resistance Tester

    Company: Qualitest International

    The Shoe Dielectric Resistance Tester is designed to test the dielectric resistance of safety or other ways insulated footwear. The Shoe Dielectric Resistance Tester applies a power (line) frequency voltage between the inner and outer electrodes of the shoe (specimen) being tested, if the test specimen does not fail, the current in mA displayed on the ammeter is the leakage current; the voltage in kV indicated by the voltmeter is the withstanding voltage. It adopts HMI,so operation is smart and visible.

  • JHMD-1 - SF6 Density Meter Tester

    Company: Xiamen Jiahua Electrical

    JHMD-1 is a smart tester. By using high accuracy core units, pressure sensor, A/D, D/A transducer, 32 bit ARM MCU and TI company's high speed signal chip, it can automatically calibrate the density relay, measure pressure at signal activity temperature, convert pressure from any temperature to 20 standard pressure, print test data and save for review. It identifies the fault during the test. The whole procedure is under automatically operation, JHMD-1 is a high accurate, high stable, reliable tester.

  • 501 - Pencil Hardness Tester

    Company: Elcometer Limited

    The Elcometer 501 Pencil Hardness Tester has been designed to ensure that the cylindrical pencil lead is maintained at a constant angle of 45° and exerts a force of 7.5N (1.68lbF).The pencil lead, prepared beforehand using the special sharpener and abrasive paper, is inserted into the Elcometer 501 hardness tester and pushed over the smooth, flat coated surface.The lowest hardness value of the pencil which marks the coating determines the coating’s hardness rating.

  • NI Series - Pendulum Impact Testers

    Company: NCS Testing Technology

    NI Series Pendulum Impact Testers are used to detect the impact resistance of metal materials under dynamic loads. It can conduct large quantities of metal impact tests continuously, display the impact absorbing energy and pre-elevation rotation angle of the pendulum and print test reports. It is useful not only for manufacturers of metal materials and quality inspection organizations, but also for research institutes for analsysi of new materials. It can use automatic sampling system to greatly improve the test efficiency and reduce the labor intensity of testers.

  • Portable Hydraulic Testers

    Company: Badger Meter

    Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.

  • P-GW Functional Tester

    Company: Polaris Networks

    The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.

  • Resiliometer - Vertical Rebound Tester

    Company: Qualitest International

    The Vertical Rebound Tester - Resiliometer is used to test the rebound or resilience property of rubber. First of all you need to level the machine and then raise the plunger at given height above the specimen. Now let the plunger to slide freely on its guide rod and then record the average resilience height for the 4th, 5th & 6th impacts. The Vertical Rebound Tester - Resiliometer is basic and conforms to the ASTM D2632 standard.

  • HTRL-V - Transformer Capacity Tester

    Company: Wuhan Huatian Electric

    Transformer Capacity Tester can test the transformer capacity, type, on-load current, on-load loss, short circuit (load) loss, resistance voltage, etc.It is small in volume, light in weight, in high accuracy, with steady property, easy to operation can replace the traditional testers. It is displayed by LCD, operated by menu, with friendly interface, is the first choice for all customers

  • WAN Tester II

    Company: TELINC

    The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.

  • WAN Tester III

    Company: TELINC

    The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.

  • SFB150 - Zinc Oxide Arrester Tester

    Company: Shanghai Launch Electric

    Zinc oxide arrester tester is specifically designed to detect internal electrical defects of power system with 10KV and below using MOA valve clearance indirect contact and to measure leakage current under MOA DC reference voltage (U1mA) and 0.75 U1mA. The instrument integrates high-voltage DC power supply, measurement and control system. All components are concentrated in a single chassis, with small size, light weight. It is a must for power system and zinc oxide arrester tester manufacturer field test.

  • Series - TT02 - Torque Tool Testers

    Company: Qualitest International

    Series TT02 Torque Tool Testers present a simple and accurate solution for testing manual, electric, and pneumatic torque screwdrivers, wrenches, and other tools. These testers are compact and rugged, suitable for production environments. A universal 3/8” square receptacle accepts common bits and attachments. The TT02 captures peak torque in both measurement directions, and also calculates 1st and 2nd peaks, useful for click-type tools.

  • Series TT02 - TORQUE TOOL TESTER

    Company: Mark-10

    Series TT02 Torque Tool Testers present a simple and accurate solution for testing manual, electric, and pneumatic torque screwdrivers, wrenches, and other tools. These testers are compact and rugged, suitable for production environments. A universal 3/8" square receptacle accepts common bits and attachments. The TT02 captures peak torque in both measurement directions, and also calculates 1st and 2nd peaks, useful for click-type tools.

  • OmniTest - Universal Hardness Tester

    Company: Qualitest International

    The OmniTest Universal Hardness Tester is designed to meet the increasing demand of versatility for the laboratory or quality control station. The unique design and advanced features eliminates operator influence during indentation measurement, thus assuring the highest repeatability. The combination of cutting edge technology and ease-of-use make the OmniTest with fully automatic image evaluation the obvious replacements for traditional mat-screen testers.

Products

Applications

Manufacturers