Showing results: 4966 - 4980 of 5196 items found.
-
IQgig-5G -
LitePoint Corporation
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
-
9195 -
TAKK Industries Incorporated
TAKK?s Model 9195 Neon Bar Checker offers a quick and inexpensive means of determining if static eliminator bars are functioning. The conveniently small pen size unit indicates that each bar emitter is performing properly by the activation of a neon light signal. Static eliminator bars may malfunction due to transformer defects, shorts in the system, need to be cleaned, etc. The bar tester may be used with shockless or ?hot? static control equipment.
-
Tester SA9083 -
JSD TestPhone Ltd
The Tester SA9083 is a battery powered, multi-range, analogue portable instrument. It is primarily intended for use by faultsmen for maintenance testing of telecommunication lines and equipment, subscriber installations connected to exchanges where faultsmen do not have access to a test desk, or where the testing equipment at the local exchange is not staffed during normal working hours. It has three input terminals, a range selector switch and a dual purpose push-button reversing switch (B-A changeover/test cell).
-
ValidATE -
SEICA SpA
Designed for electronics needs, keeping into account also the future implementations, the ValidATE system features complete test solutions for Legacy Replacement of systems like GR179X, GR275X, L200, L300, Schlumberger S7XX and other. The open and modular architecture of its hardware and software components makes the Valid technology available also in the solutions Valid MT, to meet the needs of STE system integrators, or to bring new electronics over old testers to replace the outdated.
-
R1L-BR -
TEGAM Inc.
The R1L-B series Ohmmeter/Bonding Tester is a digital microohmmeter designed to measure resistances from 10 to 20 . It is used in applications such as metal bonding, switch, circuit breaker, circuit resistance and other contact and connection resistance tests as well as higher resistance measurements for circuit analysis and resistor testing up to 20 . The instruments utilize the four-terminal, Kelvin technique to eliminate errors caused by the resistance of the leads. Resistance readings are viewed on a 3 1/2 digit display,
-
Mountz Inc.
You can reduce the risk of lost product on the line or failures in the field by using Mountz torque analyzers to ensure consistent quality. We have analyzers designed for the most efficient pass/fail assessments, models that use an internal computer to measure and display results in research and quality management environments, and even ones that connect to external torque sensors. Whatever variety you need, our torque testers are designed to fit into your processes and production environment.
-
TestEdge, Inc.
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
Kaya Instruments
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
BK9013 -
BaKo Co., Ltd
If your company produces millions of D-mics per month, take a look at the BK9013. Based on our BK3012V2 D-Mic Tester, the fully automatic BK9013 is our fastest D-Mic test system. With 4 or 8 couplers, the BK9013 can simultaneously test and sort up to 8 D-Mics into 8 passing grades and 7 different causes of failure in just a few seconds! You can view the results in real time or store them to analyze later.
-
JT 2139 -
JTAG Technologies Inc.
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
I7090 -
Keysight Technologies
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
12-2415 -
Associated Equipment Corp.
*Shown with optional 12-2416 barcode scanner*Graphical Hand-Held Tester with Thermal Printer and USB Port*Tests 12V Flooded, AGM, Gel Cell, & EFB Batteries from 100 to 2000CCA*Graphical/Symbol Based LCD display*Tests 12/24V charging and electrical systems*Stores last 70 test series with or without power*Carrying case, printing software and USB cables included*Built-in thermal printer with thermal paper (611305)*Field-Replaceable Cables (900165)
-
BOTS -
PolarSoft Inc.
BOTS is an easy-to-use BACnet regression testing tool for Windows. BOTS runs under Windows 7/8/10, and Server 2012. It provides a robust set of regression tests based on the 135.1 standard, including BTL additional tests and PolarSoft's own developer-oriented tests. BOTS includes many features tailored to the needs of QA Testers and product developers, at a price that's lower than competing systems that cost more than ten times as much.
-
ETI Precision
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
Power System -
SEICA SpA
The Power System is a test platform conceived to verify and certify the operation of power modules.The complete structure, combining two Multi standard cabinets, is sized to contain all of the resources required for testing: drive/sense modules, power modules and load simulators.In this tester, in addition to strictly perform the requested measurement as per technical specifications, the issues of consumptions and dissipations were taken into account, integrating an Energy Recovery circuit which enables reuse of output energy to supply the system.