Filter Results By:
Products
Applications
Manufacturers
-
product
6-12V Circuit Tester
TE6-0704
Hangzhou Tonny Electric & Tools Co., Ltd.
*Do-it-yourself quality*6-12 volt tester*Tests circuits with power on*Reliable and economical*Tests circuits, lights and fuses*Lights for easy visibility.*Durably designed for a long service life *For testing 6-12 volt systems for wire breaks, shorts, fuses, lamps, relays, armatures and more.*Suite able for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.
-
product
Breakout Box
T1000-15
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
Cable Fault Locator
TX4000
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
product
Automated Test Equipment
Viewpoint Systems offers design verification and manufacturing quality inspection systems to help customers reduce human error in repetitive tests, increase testing speeds, and ultimately get products to market faster at a lower cost. Viewpoint Transforms Test from Design to End-of-Line. Our R&D test systems are designed with the flexibility to validate ever-changing prototypes while accelerating your development schedule.
-
product
Drop Tester
KD 688 A
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
product
Bidirectional DC Power Supply
62000D
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
product
Automotive Simulation Software
DYNA4 Framework
TESIS DYNAware Technische Simulation Dynamischer Systeme GmbH
DYNA4 is a modular simulation software for efficient work with simulation models in the automotive development process, e. g. of electronic control units and components. Model-based design, function development. Testing and pre-calibration in SIL and HIL environments. Fail-safe and functional tests, including evaluation of vehicle response and drivability. Advanced powertrain development and energy management. Fuel efficiency simulation for hybrid (HEV), electric (EV) or traditional vehicles.
-
product
CT Tester, Meter Tester, Circuit Analyzer
GOLD MINER IV
Gold Miner is the first device of its type to test the electricity meter using exact, simultaneous measurements made on all primary and all secondary phases of the circuit. Perform in-service meter testing with a combined 3-phase load, or a single-phase load. Gold Miner not only displays the Meter’s accuracy, but also the overall, true accuracy resulting from the CTs + Meter combination for your entire measurement circuit.
-
product
Digital Multimeter
HMC8012
True RMS measurement, AC, AC + DC Simultaneous display of three measurement functions, e.g. DC + AC + statistics Measurement functions: DCV, DCI, ACV, ACI, frequency, resistance (2- and 4-wire), temperature, capacitance, diode and continuity test Mathematic functions: limit testing, minimum, maximum, average, offset, DC power, calculation of dB and dBm Data logging to internal memory or USB stick
-
product
Electro-Optical Test Software
INFRATEST
INFRATEST is a powerful software for testing IR cameras, visible and NIR cameras, ICCDs, goggles and laser rangefi nders. Based on video acquisition modules compatible with a wide range of communication protocols, including LVDS, Camera Link, GigE Vision and all types of analog formats – CCIR, PAL, RS170, NTSC, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices.
-
product
Combilog Antenna
AC-220
The AC-220 Combilog antenna is for EMC emission and immunity up to 2 GHz.. It combines the electrical properties of two antenna (biconical and Log ). It reduces overall testing time by 20 - 30% due to antenna switching. It is Optimized for emission measurements, but can handle up to 500 Watt CW, making it suitable for most immunity measurements . Each antenna is individually calibrated at 10 meters and the data included the purchase price.
-
product
Coefficient of Friction Gauges
M5-2-COF
The M5-2-COF coefficient of friction (COF) gauge is an integral part of a COF testing system, typically including a motorized test stand and COF fixture. With a capacity of 2 lbF [10 N], the gauge can be used to measure friction for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients are displayed on the backlit LCD, and are calculated from a user-programmable sled weight.
-
product
Environmental Test Chambers
TTC/CTC
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
product
Circuit Simulation & PCB Design Software
TINA Design Suite
TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.
-
product
Die Sorter Handler
4605-HTR
4605-HTR is a MAP Sorter which picks up devices from wafer ring and sorts to tape or bin according to the MAP file created by film frame test handler or prober. 4605-HTR is a high speed handling system, available for 12 inches wafer rings. When used in combination with 4170-IH, 4605-HTR much improves efficiency in testing process of leadless devices as a high speed sorting machine.
-
product
D Spectrum Analyzer
TE-3000
Antenna Technology Communications, Inc.
The TE-3000 has set the standard for field testing equipment. Not only it's a comprehensive RF test setbut also a stream analyzer. For your RF needs, it covers all your terrestrial and satellite needs. All modulationtypes analyzed along with their associated measurements. Stream analysis accommodates IP and ASI inputs.You can now test your signal all the way through from RF level to data level!
-
product
EMC Testers
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
product
Connector and Breakout Box
ES4640
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
product
Digital TV signal analyzer
1750QAM
DIGITAL TV SIGNAL ANALYZER 1750QAM? The very excellent signal analyzers of choice for field testing of QAM digital signals on your CABLE-TV SYSTEM.They demodulate and accurately measure the QAM signals carried through the cable system.They provide the measurement power the field technicians need for the latest 64-256QAM digital technologies and are very simple to use, measuring SNR(MER), EVM, Pre-BER, Post-BER, Constellation Diagram.
-
product
Eddy-Current Sensors
Eddy-Current sensors are noncontact devices capable of high-resolution measurement of the position and/or change of position of any conductive target. Eddy-Current sensors are also called inductive sensors, but generally "eddy current" refers to precision displacement instruments (or nondestructive testing probes) and "inductive" refers to inexpensive proximity switches. High resolution and tolerance of dirty environments make eddy-current sensors indispensable in today's modern industrial operations.
-
product
ESD Tester
PurePulse
Grund Technical Solutions, Inc.
PurePulse is a flexible and efficient ESD tester for HBM, TLP, MM and HMM. Its 2-pin style setup reduces tester parasitics, it captures waveform data and can be automated to test thousands of pins without the need for a test fixture. Our PurePulse system was designed from the ground up to be customized to meet your testing needs, take a look at the features below and schedule a demo with us to learn more.
-
product
Extractometer
Dynatest
*Extractometer used to measure and check the strength of fixing parts*Test carried out with a four-arm wheel or (and) the hydraulic pump with crank*Results on a pointer/digital indicator with peak value*Lightweight and easy to handle*Simple and quick setting up*Appropriate for on site testing*Packaged in a transport case (with a set of optional accessories)*Revolution counter for the crank*Delivered with a calibration results and the copy of the calibration report for the reference standard sensor
-
product
New AGM Battery Tester CCA Tester
Hangzhou Xun Anda Electrical Co., Ltd.
1. Quickly test the battery's main specifications: IR, CCA, Voltgage, so that you can judge its life status easily.2. The tool is suitable for 12V single battery or 12V Battery charging system.3. No need to charge of voltage when start the vehicle.4. Adopt conductance method to test: simple of the vehicle5. Printer inside, can print out testing results.7. LCD Screen
-
product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
product
Customer Acceptance Test Panel
TA-65
DGS-65 Customer Acceptance Panel for both testing and trouble- shooting. We have added an option to the panel that allows you to select an analog slaving meter or the LED monitor lights as shown in the maintenance manual Fig. 5-14. The addition of the meter provides the technician with a more visible means to monitor the slaving "trend". The 50 pin DG connector is broken out on the panel to assist in monitoring or isolating unit signals.
-
product
Test Rig for Flashback Arrestors
The WITT test rig allows for the testing of flashback arrestors and check valves on a regular basis.With just one device all performance tests can be carried out: leak-tightness to the atmosphere, test of check valves against reverse gas flow, functionality of the pressure sensitive gas cut-off valve and measurement of the flashback arrestors’ flow capacity.The Test Rig 722 is easy to use, has a robust design and requires no maintenance.
-
product
Portable Converged Networks Test Set
TX Series
The VeEX TX product series offers a complete test solution for Next Generation of Transport, Metro and Carrier Ethernet Testing. Color graphical display assisted with touch panel enables users tapping through the test configuration and accessing complex overhead bits and bytes. Features include APS, TDM, pointer adjustment, pulse mask analysis, G.821/G.826/M.2100, histogram, and overhead access.
-
product
Transport Expert
TX Series
The VeEX® TX product series offers a complete test solution for Next Generation of Transport, Metro and Carrier Ethernet Testing. Color graphical display assisted with touch panel enables users tapping through the test configuration and accessing complex overhead bits and bytes. Features include APS, TDM, pointer adjustment, pulse mask analysis, G.821/G.826/M.2100, histogram, and overhead access.
-
product
Thermal Shock Chamber
ETS-Series
air-to-air and liquid-to-liquid Thermal Shock Chambers from Envisys are available in different volumes to suit the varied testing needs. Horizontal or vertical models consisting of cold and hot zones with product carrier basket of sizes 50, 100, 150, 300, 600 and 900 litres which transfers the specimen under test between cold and hot zones using electro pneumatic / motorized basket movement.
-
product
Impedance Stabilization Network
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.