Applied Test Resources
Applied Test Resources (ATR) was established in 1997, with the primary objective of providing advanced Analog Test software solutions for the semiconductor Industry. As ATR's business developed, we saw an increasing need in the industry for cost effective, user-friendly, specific advanced analog test hardware. ATR then redirected our focus to develop total test solutions at highly competitive prices. Our product to meet the demand for customized test solutions at lower test costs is the MTS-2010 Mixed Signal Test System.
- (610) 488-0802
- sales@atr-inc.org
- 3219 E. Camelback Rd.
Suite 201
Phoenix, AZ 85018
USA
Filter Results By:
Products
Applications
-
product
Floating Power FET moduleAmp Loop
PFM1010
The PFM1010 Module is a precision instrument capable of measuring all common DC parameters in a power MosFet as well as many of the AC parameters. This module uses some very innovative techniques to make it possible to measure parameters like Rdson down into the sub-million-ohm range.
-
product
Four Quadrant Power Source
PM2010
The PM2010 is a four-quadrant power source capable of supplying up to 20 V/10 Amps to a load. The maximum power that may be safely generated is 50 Watts on a continuous basis and 200 Watts peak on a pulsed mode for no more than 100 ms, and a duty cycle of less than 10%
-
product
High Speed Matrix Card
MATX4001
The MATX4001 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 1 Amp and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software
-
product
High Voltage Power Source
PM1000
The PM1000 is a high voltage power source capable of supplying up to 1000 V/20 mA to a load. It is intended for use in measuring leakage and breakdown voltages of devices. There are five voltage ranges and five current ranges.
-
product
High Voltage Power Source
PM2000
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
product
Matrix Card
MATX4010
The MATX4010 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 10 Amps and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software.
-
product
Multiple (8) Four Quadrant High Power Source
PM0830
The PM0830 consists of eight fully independent four-quadrant power sources. Two of the channels are capable of supplying up to 30 V/500 mA each. The remaining six channels are capable of supplying up to 30 V/50 mA each. The PM0830 has a measurement range capable of measuring voltages up to 1000V.
-
product
Multiple (8) Four Quadrant Power Source
PM0820
The PM0820 uses an onboard controller, which relieves the system CPU of performing many functions necessary for the module operation. The result is higher efficiency of the CPU and faster execution of the module commands.
-
product
Multiple (8) High Power Four Quadrant Power Source
PM0825
The PM0825 consists of 8 fully independent four-quadrant power sources capable of supplying up to ±20V. Two of the sources are capable of up to 500mA each, four more are capable of performing at low levels with ranges of 1uA and 100uA; the remaining two are mid range with current ranges of 1mA and 100mA.
-
product
Quad Op-Amp Loop
QOAL400
The QOAL400 module is a precision instrument capable of measuring all common parameters of an Op Amp, including AC as well as DC parameters. The QOAL400 has four completely independent channels, which allow a quad device to be tested in a minimum amount of time. Each channel has a full set of resources to measure all common parameters.
-
product
Solid State Matrix Card
SSM4010
The SSM4010 module is a general purpose-switching matrix, consisting of 40 solid-state switches arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each switch has a maximum ON resistance of 5 Ohms and a minimum OFF resistance of 100 M Ohms.
-
product
Timing Measurement Unit
TMM200
The TMM200 is a resource available for measuring such parameters as propagation delays, rise time, fall time and any other time-related parameter. Because of its wide input levels, the TMM200 is an instrument well suited to test both digital an analog devices.
-
product
16 Bit Digital Card
DB1600
The DB1600 is an inexpensive digital card that provides basic digital control capability without some of the more sophisticated features available on the DRM1650. The DB1600 allows for the control of 16 bits of data. The logic levels may be programmed anywhere within the range of 12 V.
-
product
Mixed Signal Test Systems
MTS1020i
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
Floating 6-Ch Integrated Power Source
PM0650
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
