-
product
DC to 120 GHz USB Thermocouple Power Sensor
U8489A
The U8480 Series is the fastest USB thermocouple sensor in the world without compromising the best-in-class linearity of the legacy 8480/N8480 Series thermocouple sensors. The U8489A covers the widest frequency range, DC to 120 GHz.
-
product
Time Domain Analysis
S93010A
The time domain capability allows you to measure the time domain response of a device. The analyzer can transform frequency domain data to the time domain or time domain data to the frequency domain.
-
product
Noise Figure Measurements With Vector Correction
S95029B
The S95029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers by using the Keysight vector-source-correction technique. Using a source-impedance tuner to remove the effects of imperfect system-source match, this technique produces higher accuracy results than Y-factor method and other cold-source implementations--especially for in-fixture, on-wafer, and automated-test environments.
-
product
2-port E-Band VNA Using Streamline 20 GHz and 53 GHz 2-port Network Analyzers
N5253E2
Cost-effective 2-port E-band vector network analyzer (VNA) system configured with two Streamline VNAs and frequency extenders.
-
product
USB Power Sensor, 50 MHz to 24 GHz
U2002H
Measure average power over the frequency range 50 MHz to 24 GHz and power range -50 dBm to +30 dBm.
-
product
Cable Assembly, 3.5 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11500E
The Keysight 11500E is a 61 cm (24 in) 3.5-mm male to 3.5 mm male cable assembly with a frequency range of dc to 26.5 GHz.
-
product
Scalar Mixer/Converter Measurements
S96082A
The S96082A offers the solutions for measuring mixers/frequency converters and amplifier's harmonics using the ENA. The frequency offset mode (FOM) provides the capability to tune the ENA's receivers to different frequencies from the source. This enables measuring amplifier's harmonic responses and mixer/converter's conversion loss.
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-TR1
The HMMC-3128-TR1 is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
InfiniiMax Probe, 1.5 GHz
1130B
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Embedded LO Capability
S95084B
The S95084B software tunes the analyzer’s receivers to the output frequency of the converter under test without the need for access to internal LOs or a common reference signal.
-
product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 2 Prescaler
HMMC-3022
The HMMC-3022 is a DC - 12 GHz divide by two prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
20-50 GHz Doubler
1GC1-8038
The 1GG1-8038 is a passive diode frequency doubler. It is specified to operate with a 2050 GHz output frequency. Conversion efficiency is usually around -12 dB. The device has low 1/2 and 3/2 spurious output, typically 15 dBc or better. The doubler can be biased through onchip resistors to allow operation at low input levels. Up to 22 dBm at the input can be accommodated. Onchip DC blocking capacitors are included at the input and output.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
10 MHz – 18 GHz USB Power Sensor
U2000H
U2000H USB Power Sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -50 dBm to +30 dBm.
-
product
InfiniiMax Probe, 5 GHz
1132B
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
product
Frequency Converter Test Solution Up To 50 GHz
N5245BP
The N5245BP provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter test up to 50 GHz. This bundle product
-
product
Remote High Performance Receiver
E1709A
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-BLK
TheHMMC-3128-BLK is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Cable Assembly, Type-N (m) to Type-N (m), DC to 6.0 GHz
11500B
The Keysight 11500B is a 58 cm (23 in) type-N male to type-N male cable assembly with a frequency range of DC to 6.0 GHz.
-
product
Custom Systems
With our custom VNA your ATE works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
-
product
ATE Connecting Solutions
C.C.P. Contact Probes Co., LTD.
Customized pogo towers with high frequency capability.
-
product
PXIe Microwave Signal Generator, 1 MHz to 44 GHz
M9383A
Modular test solution for design validation that can be efficiently leveraged into manufacturing Flexibility to solve your immediate test needs, but upgradable for what comes next – whether that’s upgrading for frequency coverage, or a rapid shift to high volume production.Pre-5G signal confidence you need with 1% EVM @ 28 GHz, 800 MHz bandwidth
-
product
Frequency Ranges
1398A
The useable frequency range is from 5 Hz to more than 10 times higher than that listed in the table below, e.g. T2.5-1 volt and T5-2 volt can be used beyond 10 MHz.
-
product
RS232 I2C Adapter LowPower
*I2C frequency adjustable up to 100kHz*Maximum power consumption <5mA*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
PXIe Frequency Reference: 10 MHz And 100 MHz
M9300A
The M9300A PXIe frequency reference is a PXIe-compatible, compact, modular instrument that can be used with the Keysight M9301A synthesizer, M9310A source output, and M9311A modulator to create the world’s fastest vector signal generator, the M9381A. Create a CW source, the M9380A, by combining the M9300A with the M9301A and M9310A or use it as the 10-MHz or 100-MHz reference with other PXI solutions. Control the instrument through a soft front panel and programmatic interfaces tuned to your application development environment of choice.
-
product
Line Input Test
Measure the dB level and frequency of the iAudioInterface2 line input or line output (also works with any dock input audio source).