Synchro/Resolvers
Compute trigonometric values over 360 degrees of rotation by varying the magnetic couplings between its primary (rotor) and secondary (stators) windings.
See Also: Synchro / Resolver Converters, Angle Position Indicators, Stator, Rotor, Synchros, Resolvers, Synchro / Resolver Simulators
-
product
LVDT I/O Cards
IB
Computer Conversions Corporation
The "IB Series" product line are full size IBM PC/AT+ and ISA 2.01 compatible synchro, resolver, and LVDT I/O cards, and resolver-sensor card sets used as absolute encoder systems.
-
product
LVDT I/O Cards
CPE4000
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
product
6U CPCI Multifunction I/O Board
78C1
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
product
3 Channels, 0.5 VA @ 28 Vrms
DSK
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
24-Channel VME Synchro/LVDT Simulation/Acquisition Module
V545
The V545 is a generalized- DSP-based sinewave processor intended for both simulation and acquisition of LVDTs, RVDTs, synchros, and resolvers. 24 generalized, isolated channels are provided. Each channel can be a signal source or a measurement input. Users can program any desired relationship between input and output channels, allowing simulation and measurement of a wide range of inductive transducers, using internal or external excitation.
-
product
AC Reference Generators
SR21
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
product
DC-Angle to Synchro or Resolver Converters
LDS & LDR
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
product
Angle Indicators
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed multiturn synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
product
Synchro/Resolver
With so-called synchro/resolver cards, rotation angle sensors that work according to the synchro/resolver principle can be measured. Depending on the angle of rotation, these generate a sine and cosine signal, in order to determine the position and direction of rotation.
-
product
Synchro to Digital-Resolver to Digital Converters
SDC40-RDC40
Computer Conversions Corporation
The SDC series are low cost, miniature, continuous tracking, synchro or resolver to digital converters designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input and convert it into 14, 12 or 10 bit natural binary angle data.
-
product
4 Digit Angle Position Indicator (API)
TA-900
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
product
Phase Angle Voltmeter, Industry Standard
2250A
NAI's 2250A Phase Angle Voltmeter is the most accurate and versatile AC measurement tool in the Synchro/Resolver and LVDT/RVDT marketplace. Considered the industry standard and based on the latest DSP and FPGA technologies, the 2250A substantially extends and simplifies the capabilities of the legacy 2250 model.
-
product
Synchro/Resolver Conversion & Simulation PMC boards
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
product
ARINC HSI / ADI Test Fixture
TA-2000
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
product
Synchro to Digital-Resolver to Digital Converters
MSI MRI MX
Computer Conversions Corporation
Computer Conversions MX Series are low cost multiplexed synchro or resolver to digital converter sets designed for Military or Industrial diagnostic and control applicatioms requiring 3-128 axis per control.
-
product
High Accuracy AC Reference Source
515
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
product
Synchro/ARINC 429/Fuel Flow Modules
NAI designs and manufactures a wide variety of self-contained, remotely mountable, Signal Converter Modules:*Synchro/Resolver Booster AmplifiersS*ynchro/Resolver Converters*ARINC 429-to-Synchro Converters*Second Harmonic Fuel Flow ConvertersTheir field-proven designs and carefully selected components assure highly reliable performance. These military grade modules are specifically designed for rugged defense and industrial applications.
-
product
DC to Synchro and DC to Resolver Converters
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
product
AC Reference Generators
SR22
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H
-
product
Embedded Synchro - Resolver -
LVDT I/O Cards
Computer Conversions Corporation
100% Transformer Isolation is offered for all AC I/O, and various Isolated DC converters are available as standard product, eliminating concerns for ground-loops, ground interjected (intermittent and ghostly) field noise, inductive surges, differing potentials, and high voltage field transients from effecting the card itself, the sensitive ISA bus backplane and any other device or system sharing these signals.
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
product
Phase Angle Voltmeter
PAV1010A
Measuring Vrms, inphase, quadrature, freq, ratios and phase angles. Using Discrete Fourier Transform algorithms, the PAV1010A provides capability, performance and versatility not available with traditional PAVs. Targeted at the Synchro/Resolver and LVDT/RVDT marketplace, this instrument makes measurements of Phase Angle, In-Phase, Quadrature (90° component), Fundamental and Total Vrms very straightforward. All these measurements are displayed simultaneously on a bright multifunction display.
-
product
Programmable S/R Standard & Simulator
5300
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.
-
product
SR Series AC Reference Supplies
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 Volt excitation to Synchros or resolvers in military and industrial control applications. They accept +/- 15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6" x 3.1" x 1"H.
-
product
PCI D/S, S/D, I/O & Comm Board
76CS3
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Synchro/Resolver to Linear DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
