Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Triple 2 Channel Optic Mux LC
40-855-432
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Current Mirrors
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
product
Automated Laser Beam Quality Measurement System
Beamage-M2
Large Apertures: The only M2 system on the market equipped with a complete set of 50mm optics. Also, the sensor is 11.3 x 11.3 mm. Simple Alignment: Two beam-steering mirrors are included for quick and easy alignment of your laser into the system. The internal mirrors are factory-aligned and the pre-set height also simplifies the alignment.Available Fall '17
-
product
Absolute Position Measurement System
ZPS
ZYGO's ZPS™ system measures absolute position using ultra-compact optical sensors that are easily integrated into high-precision applications such as deformable mirrors and lens positioning.
-
product
Flatness Accessory Kit
55282A
The 55282A Flatness Accessory Kit is composed of an 10759A Footspacing Kit and two 10773A Flatness Mirrors. The footspacing kit provides three precision baseplates, with 50.8 mm (2 in), 101.6 mm (4 in), and 152.4 mm (6 in) pad spacing respectively, that minimize the grid setup and data accumulation time required for plate calibration. The flatness mirrors provide 100 percent reflectance and turn the direction of an incoming laser beam 90 degrees.
-
product
Modular Mounts
M-SWITCH
The M-Switch series of adjustable, modular mounts are designed to redirect a horizontal interferometric set-up to a vertical one. This vertical orientation can help reduce distortion effects commonly found from clamping, and reduce alignment time. There are 4 primary versions of hardware designed to enable testing of mirrors, windows, lenses and lens assemblies. Holding of the part under test can be done with a variable 3 arm mount (for flexibility) or our kinematic mount (for high volume). Reference mirrors can be supplied with a variety of flatness and coating specifications to match your application needs.
-
product
Optomechanical Devices
Optomechanical devices include an optical chopper, scanning galvo mirrors, adaptive optics, a motorized pinhole wheel, a piezo objective scanner, a motorized flip mount, motorized filter wheels, and optical beam shutters.
-
product
PXI Dual 2 Channel (M Mode) SC 50 Cons
40-855-222-M50
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
product
PXI Dual 2 Channel (M Mode) SC 62.5 Cons
40-855-222-M62.5
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
product
Safety Light Curtain Type 4
SF4B Ver.2
Panasonic Industrial Devices Sales Company of America
The SF4B Series offers flexibility and a wide range of accessories such as mounting brackets and extension cables. Cables for Series connection are also available to eliminate dead zones. The SF4B Series can now be equipped with corner mirrors to reduce setup work and wiring.
-
product
Light Sources
Teledyne Princeton Instruments
Variety of different light sources for UV-VIS-IR operation. All sources are supplied complete with housings, integrated refocusing mirrors, power supplies, mounting flanges for IsoPlane, SpectraPro and TriVista entrance slits. Most include cooling fans for stable operation (except TS-425).
-
product
Large Area UV Light Source
Model 30L
The OAI UV Light Source Grande is a large area collimated light source. The device is available with output power up to 10KW. Utilizing collimating mirrors, the UV Light Source Grande is a highly efficient UV light source intended for a variety of larger-scale applications.
-
product
In-Line Spark Tester
ST20610
Connect the tool between the spark plug and the plug wire to provide a quick visual check and diagnosis of the ignition system, including distributor-less ignitions. Plug wire is double-ended with a straight boot and a 90 boot for confined areas. With the engine running, the bulb mirrors the ignition spark.
-
product
Beam Directing and Reflecting Optics
Beam directing and reflecting optics simply reflect, bend or translate the beam, but do not typically modify the polarization, except for polarizing beam splitters. For example, mirrors, cube corners and retroreflectors are attached to objects that move in order to keep the weight down on the moving object (instead of mounting the interferometer on the moving object).
-
product
Fully Reflective Solar Simulators
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
product
Optical Square
10777A
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
product
Reflective Condenser
Reflective condensing system and focusing accessory for coupling light sources to monochromators. It uses two mirrors to focus to the entrance slit. The reflective system eliminates chromatic aberration, provides maximum spectral range, and does not require refocusing. Accessories like light choppers and filter wheels can also fit inside next to the slit. Versions with rotatable mirror available for up to four source direction.
-
product
Network Simulator
SWAT WDS
Alethea Communications Technologies Pvt Ltd
Alethea’s SWAT WDS Network Simulator emulates the whole Customer Premises side with one box generating up to 32 CPEs with 4 ~ 8 ethernet clients behind each CPE. This setup which mirrors actual field deployment allows transmission points to be checked in detail as soon as the access point is setup. The solution gives a calibrated measure of the User Experience expected over the deployed system.
-
product
Turning Mirror
10769A
The 10769A is ideal for use in laser measurement and calibration applications. In the calibration of slant bed lathes, for example, the beam steering mirror deflects the beam from the laser head upward, through the interferometer, along the lathe's cross slide. One or more mirrors can also create a path from a laser head to an interferometer located in an otherwise inaccessible position, as in the case of a milling machine with a table that moves in only one axis.
-
product
Radiation Pressure Series
The Radiation Pressure Series is Scientech’s newest innovation, designed to accurately measure high power levels from lasers that would normally require expensive, large water-cooled calorimeters. These instruments measure the radiation force exerted by the laser beam on a mirror and significantly improve response time, size, and scalability. The mirrors are designed to reflect ≥99.999% of the laser energy and allow continuous measurement. Radiation Pressure Series instruments actually improve in accuracy as laser power increases.
-
product
Optical Communications and Sensing
The Analog Devices optical portfolio covers a range of technologies, such as current mirrors, translinear logarithmic amplifiers, laser diode driver ICs, and optical sensors, to provide designers the tools they need for their optical applications. Our optical portfolio supports GbE optical receivers, Fibre Channel, WDM transponders, telecommunications, and next-generation optical networks.
-
product
Optics
Rising from our Qioptiq® heritage, Excelitas now offers precision optics in most every form and spanning the entire spectrum. You can choose from more than 4,800 off-the-shelf optical products! Our selection includes plano-convex lenses, biconvex lenses, aspheres and achromats with individual coatings, as well as plano optics, mirrors, polarization optics, electro-optics and optical design software and of course our optical assemblies and systems, such as objective lenses, optronics modules, and complex custom sub-assemblies and turn-key systems.
-
product
Chilled Mirror Hygrometers
We are internationally recognized as a leading developer and manufacturer of the high-quality MBW Calibration chilled mirror dew point hygrometers used in a variety of humidity calibration, measurement and gas quality applications. Most notably, our MBW instruments provide the calibration traceability for many laboratories such as humidity instrument manufacturers and National Metrology Institutes. Our MBW chilled dew point mirrors continue to be chosen as transfer standards for inter-laboratory comparisons both regionally and internationally.
-
product
PXI Quad 2x2 Fibre Optic Mux MU
40-860-342
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Dual 2 Channel Fiber MUX ST
40-855-522-M
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 2 Channel Optic Mux FC/PC
40-855-112
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Dual 2 Channel Fibre Optic LC
40-855-422
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 2 x 2 Insert/Bypass Switch FC/APC
40-860-012
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Quad 2 Channel Fibre Optic MU
40-855-342
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 2 Channel Fibre Optic MU
40-855-312
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 2 Channel Fiber MUX SC
40-855-212-M
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
