Filter Results By:
Products
Applications
Manufacturers
Absorbers
dampen wave reflection.
- Taylor Dynamometer, Inc.
product
Towing Dynamometer
RS-90K
RS-90K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-90K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-90K is designed to maintain 90,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Shock Absorber Tester
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
product
Shock Absorber Filling System
MS200
The system is used for filling mono-tube and twin-tube shock absorbers with gas after repair. MS200 has pressure adjustment function and is used for shock absorbers of power pressure up to 120 bar.
-
product
Shock Absorber Test Rig
Defective shock absorbers impair the car's handling, unevenness on the road starts to be felt more strongly and the stability of the car at a high speed decreases. Check the shock absorbers visually, in motion, under load, and also in the service center on special equipment. In case of visual diagnostics, it is necessary to inspect the shock absorbers carefully, if there are signs of oil leakage on the body, this indicates a breach of the chamber tightness due to wear or damage to the glands and other sealing elements.
-
product
Test Bench for Shock Absorbers
MS1000+
Test bench for diagnosticsof shock absorbers of any type. The equipment conducts quick and accurate testing with an opportunity to checkoperation under different speed. Thesystem fixesperformance parameters under different speed.
-
product
ESD Safe Fume Absorber
ESD safe, carbon-activated fume absorber. Flux creates "pine resin", which creates noxious fumes. These fumes cause headaches and nausea. This unit quickly removes these fumes from the work area and filters them safely. Only this newly developed unit, mounted on its versatile 37" arms, allows easy movement to effectively remove these irritating fumes fast.
-
product
Absorber Lined Shielding Enclosure Measurements
ALSE
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
product
DC Power / Energy Absorber Test System
AMETEK Programmable Power, Inc.
The Energy Absorber Test System includes power supplies and a regenerative energy absorber with a rating of 400VDC at ±150A. The system consists of DC power supplies, an AC distribution and interlock system, an energy absorber chassis and an absorber load resistor chassis. The power sources are equipped with a remote control option allowing control via GPIB or with front panel controls in local mode. The operation of the specific parts of the system is described in the sections below.
-
product
Medium Voltage Iron Core Oil-Immersed Shunt Reactor
Iron core Oil-immersed Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system.
-
product
Diesel Dynamometers
Heavy-duty toroidal water-brake or large eddy-current absorber, S-beam electronic torque transducer, high-flow manual (or optional electronic) engine load control, DYNOmite data-acquisition computer, rigid-frame engine test stand, wall (or stand) mounted control console, absorber to engine-block mounting adapter, heavy-duty input shaft, calibration arm, stainless-braided hoses, and full-function data wiring harness.
-
product
NDT Wedges
Rexolite or perspex wedges incorporate a pyramidal scattering surface with an impedance matched acoustic absorber to minimise internal reflections within the wedge.
-
product
PWC Dynamometers
Mount the DYNOmite absorber (and appropriate pump adapter) in place of the boat's standard nozzle and cone. Each pump adapter (sold separately) incorporates a shaft, driven by the impeller (without impeller removal). A load control valve (fed from your " garden hose) allows you to regulate RPM by varying absorber drag (while holding the throttle open). You can simulate running at any MPH from idle to top end. The DYNOmite's computer captures the engine's RPM from an (integral absorber mounted) magnetic RPM pickup. Torque readings come directly from a full-bridge (temperature- compensated) torque arm. Results are never estimated from vague hydraulic-pump pressures.
-
product
Antenna Test Chamber
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
product
High Frequency Retrofits and Relocations
Our services also include upgrades of existing HF chambers to meet new program requirements, absorber installations, and relocations of chambers from one site to another.
-
product
RF Data, manipulation software
EMiDat
EMiDat is a powerful Windows application allowing the manipulation of calibration data for the assessment of absorber lined screened rooms. Field uniformity can be established giving both graphical and tabular information
-
product
Shore A Type Hardness Tester Rubber Hardness Tester
HS-A
Shenzhen Chuangxin Instruments Co., Ltd.
HS-A is a digital Shore A type hardness tester. It is suitable for plastic (such as film, medical appliance, etc.), synthetic rubber(such as seals, tires, rubber roller, rubber hose/belt, wire and cable, shock absorber, etc.) and other related chemical products.
-
product
Power Detectors
Get accurate measurements with fast response times with our thermopile or pyroelectric power meters. Available with various absorbers, with the highest damage thresholds you can find in their category, our power meters cover a wide range going from the nanowatts to multi-kilowatts.
-
product
Small Engine Dynamometers
Toroidal-flow water-brake absorber (with 5" high-RPM rotor), electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer, AC power supply, stainless-braided hoses, magnetic RPM sensor, data wiring harness, and protective carrying case.
-
product
Antenna Testing Services
Our chamber measures 28' x 14' x 14' with 12" to 36" pyramidal anechoic absorbers and is fully shielded using a dual layer metal enclosure. Our test chamber is designed to for frequencies ranging from .700 to 6.00 GHz.
-
product
Towing Dynamometer
RSL-8K
RSL-8K Towing Dynamometer is designed for testing today’s mid-sized cars and compact SUVs. The RSL-8K is built with an all-aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-8K uses an eddy current absorber for power absorption. The power is provided by batteries and an alternator.
-
product
Towing Dynamometer
RSL-5.4K
RSL-5.4K Towing Dynamometer is designed for testing today’s compact cars. The RSL-5.4K is built with an all aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL 5.4K uses an eddy current absorber for power absorption. The power is provided by batteries and an alternator.
-
product
Anechoic Chamber
EMC-3
A 3 meter test range ensuring fully compliant Emission and Immunity testing. Ferrite and hybrid pyramidal absorbers are combined in a unique pattern within a SmartShield high performance chamber. Operating at a 3m test distance, this chamber is compliant to CISPR-16 with a measurement zone diameter of 1-2 meters.
-
product
Towing Dynamometer
RSL-25K
RSL-25K Towing Dynamometer is designed for testing today’s full-sized cars, SUVs and light trucks. The RSL25K is built with a steel frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-25K uses eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
product
High-Power Detector Laser Power Meters
11PMK-W5
11PMK-W5 power detectors surface absorber stands up to average power densities of 100 kW/cm². That is the best in the world for average power density. 11PMK-W5 high-power detectors come ready to mount on a rod, a bracket and the square case even lets you set them right on the optical table.
-
product
Towing Dynamometer
RSL-10K
RSL-10K Towing Dynamometer is designed for testing today’s full-sized cars, SUVs and light trucks. The RSL-10K is built with an all-aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL 10K uses an eddy current absorber for power absorption. The power is provided by batteries and an alternator.
-
product
Net Radiation Measurement
NR Lite2
The design of the NR Lite2 is unique. The detector is based on a Teflon coated, weather resistant black conical absorber. In contrast to other sensor designs, NR Lite2 requires no fragile plastic domes. This results in a virtually maintenance free design. The vertical stick prevents birds from affecting the output signal.
-
product
Snowmobile Dynamometer
Standard dyno kit includes: 9" toroidal-flow water-brake absorber, electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer with backlit LCD and keypad interface option, AC power supply, stainless-braided hoses, puller bolt, data wiring harness, and protective carrying case.
-
product
Anechoic chambers
The anechoic chambers are built up as a modular construction. Due to individual modules any size of chamber can be manufactured. Big chambers may require an outer supporting structure or alternatively the shielding material can be attached direct to the building. The absorbers are fixed to rails bars or wooden base construction which is inserted into the shielding modules.
-
product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
product
GTEM cells
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
product
Structural Durability Solutions
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.